Flexural Properties of Thin-Walled Specimens with Square Hollow Sections 3D Printed from ABS Reinforced with Aramid Fibers

IF 4 Q2 MATERIALS SCIENCE, MULTIDISCIPLINARY Fibers Pub Date : 2023-09-17 DOI:10.3390/fib11090077
Jerzy Bochnia, Tomasz Kozior, Mateusz Musialek
{"title":"Flexural Properties of Thin-Walled Specimens with Square Hollow Sections 3D Printed from ABS Reinforced with Aramid Fibers","authors":"Jerzy Bochnia, Tomasz Kozior, Mateusz Musialek","doi":"10.3390/fib11090077","DOIUrl":null,"url":null,"abstract":"This article studies the flexural behavior of thin-walled specimens with square hollow sections fabricated using fused deposition modeling (FDM). The specimens were 3D printed from an ABS filament reinforced with aramid fibers. Four wall thicknesses were analyzed. The strength data were collected during three-point flexural tests. There are visible, clear differences in the flexural properties between the X- or Y-oriented specimens and those printed in the Z direction, and they vary up to 70%. It was also found that the flexural strength was dependent on the G-codes controlling the print head’s motion, path, and position. For specimens with a thickness up to 1.4 mm, the infill pattern was linear, whereas 1.8 mm and 2 mm specimens needed a stitch, which had some negative effects on the strength properties.","PeriodicalId":12122,"journal":{"name":"Fibers","volume":"11 1","pages":"0"},"PeriodicalIF":4.0000,"publicationDate":"2023-09-17","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Fibers","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.3390/fib11090077","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q2","JCRName":"MATERIALS SCIENCE, MULTIDISCIPLINARY","Score":null,"Total":0}
引用次数: 0

Abstract

This article studies the flexural behavior of thin-walled specimens with square hollow sections fabricated using fused deposition modeling (FDM). The specimens were 3D printed from an ABS filament reinforced with aramid fibers. Four wall thicknesses were analyzed. The strength data were collected during three-point flexural tests. There are visible, clear differences in the flexural properties between the X- or Y-oriented specimens and those printed in the Z direction, and they vary up to 70%. It was also found that the flexural strength was dependent on the G-codes controlling the print head’s motion, path, and position. For specimens with a thickness up to 1.4 mm, the infill pattern was linear, whereas 1.8 mm and 2 mm specimens needed a stitch, which had some negative effects on the strength properties.
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
用芳纶纤维增强ABS 3D打印方形空心截面薄壁试件的弯曲性能
本文采用熔融沉积模型(FDM)对方形空心截面薄壁试件的受弯性能进行了研究。这些样品是用芳纶纤维增强的ABS长丝3D打印的。分析了四种壁厚。强度数据是在三点弯曲试验中收集的。X或y方向的样品与Z方向的样品在弯曲性能上有明显的差异,差异可达70%。研究还发现,弯曲强度与控制打印头运动、路径和位置的g码有关。对于厚度为1.4 mm的试件,填充模式为线性,而1.8 mm和2 mm的试件需要缝合,这对强度性能有一定的负面影响。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 去求助
来源期刊
Fibers
Fibers Engineering-Civil and Structural Engineering
CiteScore
7.00
自引率
7.70%
发文量
92
审稿时长
11 weeks
期刊介绍: Fibers (ISSN 2079-6439) is a peer-reviewed scientific journal that publishes original articles, critical reviews, research notes and short communications on the materials science and all other empirical and theoretical studies of fibers, providing a forum for integrating fiber research across many disciplines. Our aim is to encourage scientists to publish their experimental and theoretical results in as much detail as possible. There is no restriction on the length of the papers. The full experimental details must be provided so that the results can be reproduced. Electronic files or software regarding the full details of the calculation and experimental procedure, if unable to be published in a normal way, can be deposited as supplementary material. The following topics are relevant and within the scope of this journal: -textile fibers -natural fibers and biological microfibrils -metallic fibers -optic fibers -carbon fibers -silicon carbide fibers -fiberglass -mineral fibers -cellulose fibers -polymer fibers -microfibers, nanofibers and nanotubes -new processing methods for fibers -chemistry of fiber materials -physical properties of fibers -exposure to and toxicology of fibers -biokinetics of fibers -the diversity of fiber origins
期刊最新文献
Raman Spectra of Delignified Plant Fibers: Exploring the Impact of Xylan’s Presence on the Spectral Features of Cellulose Pulp Particle Classification Based on Optical Fiber Analysis and Machine Learning Techniques Mechanical Performance of Cementitious Materials Reinforced with Polyethylene Fibers and Carbon Nanotubes Development of Activated Carbon Textiles Produced from Jute and Cotton Wastes for Electromagnetic Shielding Applications Mechanical Properties of 3D-Printed Carbon Fiber-Reinforced Cement Mortar
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1