A. H. Abdullah, I. Tharazi, F. M. Salleh, N. H. A. Halim, Z. H. Solihin, Afeeqa Puteri Marzuki, K. Abdan
{"title":"Tensile properties and dynamic mechanical analysis of kenaf/epoxy composites","authors":"A. H. Abdullah, I. Tharazi, F. M. Salleh, N. H. A. Halim, Z. H. Solihin, Afeeqa Puteri Marzuki, K. Abdan","doi":"10.15282/jmes.18.1.2024.3.0778","DOIUrl":null,"url":null,"abstract":"Kenaf fibre-reinforced polymer composites could offer low-cost, biodegradable, recyclable, and renewable materials. The hydrophilic kenaf fibres exhibit poor compatibility with the hydrophobic epoxy matrix as compared to their synthetic counterparts and ultimately, this may severely constrain their potential as a green composite material. This work aims to evaluate the tensile properties and dynamic mechanical analysis (DMA) of kenaf fibre composites reinforced with two epoxy systems as matrices, B and M resins. Neat epoxy samples and kenaf-reinforced composites with varying fibre loading, 15% and 45% were fabricated in the study. It was found that the tensile properties of kenaf composites are dependent on the epoxy resin systems and higher with reinforcement content. The tensile strength of M-15% and M-45% are 16.3% and 12.0% stronger than their counterparts. Determination of interfacial shear strength using a modified micromechanical model was employed showing that M-45 has a higher value than B-45%, 107.09 kPa and 90.28 kPa respectively. By DMA, in general, an increase in the storage modulus and peak height in the loss modulus was always higher with kenaf composites that were manufactured with the M resin system. The adhesion factor, A calculated from tan delta curves and cole-cole plot has shown the state of fibre/matrix adhesion level in each epoxy resin system. The SEM analysis indicates the presence of void spaces around fibres and matrix may attributed to the lower compatibility of the B resins system used in kenaf composites fabrication.","PeriodicalId":16166,"journal":{"name":"Journal of Mechanical Engineering and Sciences","volume":null,"pages":null},"PeriodicalIF":1.1000,"publicationDate":"2024-03-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Journal of Mechanical Engineering and Sciences","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.15282/jmes.18.1.2024.3.0778","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q4","JCRName":"ENGINEERING, MECHANICAL","Score":null,"Total":0}
引用次数: 0
Abstract
Kenaf fibre-reinforced polymer composites could offer low-cost, biodegradable, recyclable, and renewable materials. The hydrophilic kenaf fibres exhibit poor compatibility with the hydrophobic epoxy matrix as compared to their synthetic counterparts and ultimately, this may severely constrain their potential as a green composite material. This work aims to evaluate the tensile properties and dynamic mechanical analysis (DMA) of kenaf fibre composites reinforced with two epoxy systems as matrices, B and M resins. Neat epoxy samples and kenaf-reinforced composites with varying fibre loading, 15% and 45% were fabricated in the study. It was found that the tensile properties of kenaf composites are dependent on the epoxy resin systems and higher with reinforcement content. The tensile strength of M-15% and M-45% are 16.3% and 12.0% stronger than their counterparts. Determination of interfacial shear strength using a modified micromechanical model was employed showing that M-45 has a higher value than B-45%, 107.09 kPa and 90.28 kPa respectively. By DMA, in general, an increase in the storage modulus and peak height in the loss modulus was always higher with kenaf composites that were manufactured with the M resin system. The adhesion factor, A calculated from tan delta curves and cole-cole plot has shown the state of fibre/matrix adhesion level in each epoxy resin system. The SEM analysis indicates the presence of void spaces around fibres and matrix may attributed to the lower compatibility of the B resins system used in kenaf composites fabrication.
期刊介绍:
The Journal of Mechanical Engineering & Sciences "JMES" (ISSN (Print): 2289-4659; e-ISSN: 2231-8380) is an open access peer-review journal (Indexed by Emerging Source Citation Index (ESCI), WOS; SCOPUS Index (Elsevier); EBSCOhost; Index Copernicus; Ulrichsweb, DOAJ, Google Scholar) which publishes original and review articles that advance the understanding of both the fundamentals of engineering science and its application to the solution of challenges and problems in mechanical engineering systems, machines and components. It is particularly concerned with the demonstration of engineering science solutions to specific industrial problems. Original contributions providing insight into the use of analytical, computational modeling, structural mechanics, metal forming, behavior and application of advanced materials, impact mechanics, strain localization and other effects of nonlinearity, fluid mechanics, robotics, tribology, thermodynamics, and materials processing generally from the core of the journal contents are encouraged. Only original, innovative and novel papers will be considered for publication in the JMES. The authors are required to confirm that their paper has not been submitted to any other journal in English or any other language. The JMES welcome contributions from all who wishes to report on new developments and latest findings in mechanical engineering.