Khettawan Preecha, Sasirat Chaideesungnoen, P. Muangjunburee
{"title":"Microstructure and Fatigue Behavior of Cr-Mo Steel Weld Joints with Automatic TIG Welding","authors":"Khettawan Preecha, Sasirat Chaideesungnoen, P. Muangjunburee","doi":"10.12982/cmjs.2024.021","DOIUrl":null,"url":null,"abstract":"This research focused on how filler metal and post-weld heat treatment (PWHT) affected the microstructure and mechanical properties of 2.25Cr-1Mo steel welds, especially the fatigue behavior. Automatic TIG welding was used to fabricate the weld samples, and both AWS A5.28 ER90S-B3 (also known as B3) and AWS A5.14 ERNiCrMo-3 (commonly known as Inconel 625) were used as filler metals. The PWHT was performed at 690°C for one hour. That was the ideal condition for reducing the hardness of the heat affected zone (HAZ). The microstructure of the B3 weld metal and the HAZ was observed to alter from bainite to tempered bainite due to PWHT, resulting in a decrease in hardness (B3 WM: from 299.7 to 243.5 HV0.2 and HAZ: from 294.5 to 234.7 HV0.2). On the other hand, Inconel 625 weld metal showed an austenite microstructure: after PWHT, the formation of gamma prime increased its hardness (from 263.2 to 299.8 HV0.2). According to the tensile test results, the tensile strength of the welded samples was slightly lower than that of the original base metal, such as the UTS of the BM was 633.0 ± 3.0 MPa and that of the B3-PWHT sample was 601.4 ± 2.0 MPa. The effect of PWHT on tensile strength was negligible, but it significantly affected fatigue strength. For both filler metals, PWHT resulted in a decrease in fatigue strength. The fatigue strength of the B3 sample decreased from 290 to 120 MPa, while that of the IN625 sample reduced from 290 to 240 MPa. In comparison between two different materials, the fatigue strength of the Inconel 625 sample was greater than that of the B3 sample. Fatigue fracture surfaces can be classified into three stages: crack initiation, propagation, and fast fracture. The fatigue rupture was mostly initiated at the weld interface. The final fracture revealed a dimple appearance.","PeriodicalId":9884,"journal":{"name":"Chiang Mai Journal of Science","volume":null,"pages":null},"PeriodicalIF":0.6000,"publicationDate":"2024-03-29","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Chiang Mai Journal of Science","FirstCategoryId":"103","ListUrlMain":"https://doi.org/10.12982/cmjs.2024.021","RegionNum":4,"RegionCategory":"综合性期刊","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q3","JCRName":"MULTIDISCIPLINARY SCIENCES","Score":null,"Total":0}
引用次数: 0
Abstract
This research focused on how filler metal and post-weld heat treatment (PWHT) affected the microstructure and mechanical properties of 2.25Cr-1Mo steel welds, especially the fatigue behavior. Automatic TIG welding was used to fabricate the weld samples, and both AWS A5.28 ER90S-B3 (also known as B3) and AWS A5.14 ERNiCrMo-3 (commonly known as Inconel 625) were used as filler metals. The PWHT was performed at 690°C for one hour. That was the ideal condition for reducing the hardness of the heat affected zone (HAZ). The microstructure of the B3 weld metal and the HAZ was observed to alter from bainite to tempered bainite due to PWHT, resulting in a decrease in hardness (B3 WM: from 299.7 to 243.5 HV0.2 and HAZ: from 294.5 to 234.7 HV0.2). On the other hand, Inconel 625 weld metal showed an austenite microstructure: after PWHT, the formation of gamma prime increased its hardness (from 263.2 to 299.8 HV0.2). According to the tensile test results, the tensile strength of the welded samples was slightly lower than that of the original base metal, such as the UTS of the BM was 633.0 ± 3.0 MPa and that of the B3-PWHT sample was 601.4 ± 2.0 MPa. The effect of PWHT on tensile strength was negligible, but it significantly affected fatigue strength. For both filler metals, PWHT resulted in a decrease in fatigue strength. The fatigue strength of the B3 sample decreased from 290 to 120 MPa, while that of the IN625 sample reduced from 290 to 240 MPa. In comparison between two different materials, the fatigue strength of the Inconel 625 sample was greater than that of the B3 sample. Fatigue fracture surfaces can be classified into three stages: crack initiation, propagation, and fast fracture. The fatigue rupture was mostly initiated at the weld interface. The final fracture revealed a dimple appearance.
期刊介绍:
The Chiang Mai Journal of Science is an international English language peer-reviewed journal which is published in open access electronic format 6 times a year in January, March, May, July, September and November by the Faculty of Science, Chiang Mai University. Manuscripts in most areas of science are welcomed except in areas such as agriculture, engineering and medical science which are outside the scope of the Journal. Currently, we focus on manuscripts in biology, chemistry, physics, materials science and environmental science. Papers in mathematics statistics and computer science are also included but should be of an applied nature rather than purely theoretical. Manuscripts describing experiments on humans or animals are required to provide proof that all experiments have been carried out according to the ethical regulations of the respective institutional and/or governmental authorities and this should be clearly stated in the manuscript itself. The Editor reserves the right to reject manuscripts that fail to do so.