Effect of Layer Height on Tenile Strength of Fused Deposited Modeling Printed Carbon Poly-Lactic Acid Part

Sumitkumar Y Patel, Dr. Chaitanya K. Desai
{"title":"Effect of Layer Height on Tenile Strength of Fused Deposited Modeling Printed Carbon Poly-Lactic Acid Part","authors":"Sumitkumar Y Patel, Dr. Chaitanya K. Desai","doi":"10.55041/ijsrem37009","DOIUrl":null,"url":null,"abstract":"Fused deposition modelling (FDM) is an additive manufacturing process that creates objects by depositing successive layers of material. FDM is the most widely used additive manufacturing process because of its ability to create complex geometries. Various FDM process parameter affects the mechanical property of FDM objects. The main objective of this paper to stud the layer height of specimens, one of the important process parameter, build using Carbon poly-lactic acid part(C-PLA) with FDM process. For that Dogbone specimens as per ASTM D638-14 standard prepared using FDM process with three different layer height(h) of 0.12 mm, 0.23 mm and 0.35 mm. Three different sets of specimens with 0 0 ,450 , 900 raster orientation (θ) were printed using FDM process. Then specimens were tested on UTM machine to evaluate ultimate tensile strength for all specimens. Results show that high tensile strength found for lower layer height specimens compare to higher layer height specimens. Keywords: Fused deposition modeling, Tensile strength, Elastic modulus,PLA","PeriodicalId":13661,"journal":{"name":"INTERANTIONAL JOURNAL OF SCIENTIFIC RESEARCH IN ENGINEERING AND MANAGEMENT","volume":"64 4","pages":""},"PeriodicalIF":0.0000,"publicationDate":"2024-08-09","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"INTERANTIONAL JOURNAL OF SCIENTIFIC RESEARCH IN ENGINEERING AND MANAGEMENT","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.55041/ijsrem37009","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
引用次数: 0

Abstract

Fused deposition modelling (FDM) is an additive manufacturing process that creates objects by depositing successive layers of material. FDM is the most widely used additive manufacturing process because of its ability to create complex geometries. Various FDM process parameter affects the mechanical property of FDM objects. The main objective of this paper to stud the layer height of specimens, one of the important process parameter, build using Carbon poly-lactic acid part(C-PLA) with FDM process. For that Dogbone specimens as per ASTM D638-14 standard prepared using FDM process with three different layer height(h) of 0.12 mm, 0.23 mm and 0.35 mm. Three different sets of specimens with 0 0 ,450 , 900 raster orientation (θ) were printed using FDM process. Then specimens were tested on UTM machine to evaluate ultimate tensile strength for all specimens. Results show that high tensile strength found for lower layer height specimens compare to higher layer height specimens. Keywords: Fused deposition modeling, Tensile strength, Elastic modulus,PLA
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
层高对熔融沉积模型打印碳聚乳酸部件韧性强度的影响
熔融沉积建模(FDM)是一种快速成型制造工艺,通过连续沉积材料层来制造物体。FDM 是应用最广泛的快速成型制造工艺,因为它能够制造复杂的几何形状。各种 FDM 工艺参数会影响 FDM 物体的机械性能。本文的主要目的是研究试样的层高,这是使用 FDM 工艺制造碳聚乳酸部件(C-PLA)的重要工艺参数之一。为此,根据 ASTM D638-14 标准,使用 FDM 工艺制备了狗骨试样,试样有三种不同的层高(h),分别为 0.12 毫米、0.23 毫米和 0.35 毫米。使用 FDM 工艺打印了 0 0、450 和 900 光栅方向 (θ) 的三组不同试样。然后在 UTM 机上对试样进行测试,以评估所有试样的极限抗拉强度。结果表明,与层高较高的试样相比,层高较低的试样抗拉强度较高。关键词熔融沉积模型 拉伸强度 弹性模量 聚乳酸
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 去求助
来源期刊
自引率
0.00%
发文量
0
期刊最新文献
Exploring Vulnerabilities and Threats in Large Language Models: Safeguarding Against Exploitation and Misuse Experimental Investigation of Leachate Treatment Using Low-Cost Adsorbents Exploring Vulnerabilities and Threats in Large Language Models: Safeguarding Against Exploitation and Misuse BANK TRANSACTION USING IRIS AND BIOMETRIC Experimental Investigation of Leachate Treatment Using Low-Cost Adsorbents
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1