Estimation of Relative Resource Circulation for Heat Exchangers Using Material Flow Analysis for Air Conditioners

Shoma Fujii, Yuko Oshita, Yasunori Kikuchi, Satoshi Ohara
{"title":"Estimation of Relative Resource Circulation for Heat Exchangers Using Material Flow Analysis for Air Conditioners","authors":"Shoma Fujii, Yuko Oshita, Yasunori Kikuchi, Satoshi Ohara","doi":"10.20965/ijat.2022.p0737","DOIUrl":null,"url":null,"abstract":"The demand for resource circulation of heat exchangers in air conditioners is expected to grow rapidly; however, the market stocking time is relatively long. Therefore, this scenario was used as a case study for sustainable products design. A material flow analysis was conducted to estimate the balance between global relative resource consumption for shipment, waste, and installed stock from publicly available information up to 2050. Based on the projected demand through 2050, the shipment volume for each year was calculated on a cooling capacity basis. From this analysis, the waste volume was calculated. Using the shipment volume on the basis of yearly cooling capacity, the shipment volume on a resource basis was calculated considering the heat transfer coefficient. The balance between the waste volume and the installed stock was estimated. The resource circulation was simulated by defining variables such as the ratio of units that can be converted from waste to shipment and the ratio of heat exchangers using circulated resources in the total number of shipments. The results indicate that the shipment, waste, and installed stock of resources projected for 2050 were greater than those at the 2021 levels by factors of 2.2, 2.8, and 2.9, respectively. In addition, they were greater than those of the 2021 levels in the scenarios by factors of 1.8, 2.2, and 2.8 accounting for the increase of heat transfer coefficient into account, indicating the importance of improvement of heat transfer. The simulation of circulation showed that a fully closed loop in 2050 would be difficult to achieve owing to the shortage of heat exchangers for waste-to-shipment. Sensitivity analysis also indicated that even under conditions where there is no predicted shortage of circulated resources for 2050, achieving the target in a short period of time may cause a rapid increase in demand for circulating resources. This would subsequently, lead to a shortage of supply compared to demand. Thus, it is important to account for these dynamics relating resource circulation and strategy planning during analysis.","PeriodicalId":13583,"journal":{"name":"Int. J. Autom. Technol.","volume":"32 1","pages":"737-746"},"PeriodicalIF":0.0000,"publicationDate":"2022-11-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Int. J. Autom. Technol.","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.20965/ijat.2022.p0737","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
引用次数: 0

Abstract

The demand for resource circulation of heat exchangers in air conditioners is expected to grow rapidly; however, the market stocking time is relatively long. Therefore, this scenario was used as a case study for sustainable products design. A material flow analysis was conducted to estimate the balance between global relative resource consumption for shipment, waste, and installed stock from publicly available information up to 2050. Based on the projected demand through 2050, the shipment volume for each year was calculated on a cooling capacity basis. From this analysis, the waste volume was calculated. Using the shipment volume on the basis of yearly cooling capacity, the shipment volume on a resource basis was calculated considering the heat transfer coefficient. The balance between the waste volume and the installed stock was estimated. The resource circulation was simulated by defining variables such as the ratio of units that can be converted from waste to shipment and the ratio of heat exchangers using circulated resources in the total number of shipments. The results indicate that the shipment, waste, and installed stock of resources projected for 2050 were greater than those at the 2021 levels by factors of 2.2, 2.8, and 2.9, respectively. In addition, they were greater than those of the 2021 levels in the scenarios by factors of 1.8, 2.2, and 2.8 accounting for the increase of heat transfer coefficient into account, indicating the importance of improvement of heat transfer. The simulation of circulation showed that a fully closed loop in 2050 would be difficult to achieve owing to the shortage of heat exchangers for waste-to-shipment. Sensitivity analysis also indicated that even under conditions where there is no predicted shortage of circulated resources for 2050, achieving the target in a short period of time may cause a rapid increase in demand for circulating resources. This would subsequently, lead to a shortage of supply compared to demand. Thus, it is important to account for these dynamics relating resource circulation and strategy planning during analysis.
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
用空调物料流分析估算换热器相对资源循环
空调换热器资源循环需求有望快速增长;但市场备货时间相对较长。因此,这个场景被用作可持续产品设计的案例研究。我们进行了一项物料流分析,以根据公开信息估计到2050年全球运输、废物和已安装库存的相对资源消耗之间的平衡。根据到2050年的预计需求,每年的出货量是以制冷量为基础计算的。根据这一分析,计算了废物量。采用以年制冷量为基础的发货量,考虑换热系数计算资源基础上的发货量。估计了废物量和已安装库存之间的平衡。通过定义变量来模拟资源循环,例如可以从废物转化为运输的单位的比例,以及使用循环资源的热交换器在总运输数量中的比例。结果表明,2050年预计的资源运输量、浪费量和装机存量分别比2021年增加2.2倍、2.8倍和2.9倍。此外,考虑到换热系数的增加,在1.8、2.2和2.8的倍数下,各情景下的换热系数均大于2021年的水平,表明改善换热的重要性。循环模拟表明,由于缺乏用于废物运输的热交换器,2050年将难以实现完全闭环。敏感性分析还表明,即使在2050年循环资源预测不短缺的情况下,在短时间内实现这一目标也可能导致循环资源需求的快速增长。这随后会导致供大于求。因此,在分析过程中考虑这些与资源循环和战略规划有关的动态是很重要的。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 去求助
来源期刊
自引率
0.00%
发文量
0
期刊最新文献
Advantages of Injection Mold with Hybrid Process of Metal Powder Bed Fusion and Subtractive Process Experimental Investigation of Spatter Particle Behavior and Improvement in Build Quality in PBF-LB Process Planning with Removal of Melting Penetration and Temper Colors in 5-Axis Hybrid Additive and Subtractive Manufacturing Technique for Introducing Internal Defects with Arbitrary Sizes and Locations in Metals via Additive Manufacturing and Evaluation of Fatigue Properties Editorial: Recent Trends in Additive Manufacturing
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1