铸造超级双相耐腐蚀钢的热变形建模

IF 0.4 Q4 METALLURGY & METALLURGICAL ENGINEERING Russian Metallurgy (Metally) Pub Date : 2024-03-19 DOI:10.1134/S0036029523120315
S. V. Rushchits, N. A. Shaburova, V. V. Sedukhin, A. M. Akhmed’yanov, S. P. Samoilov, A. N. Anikeev, I. V. Chumanov
{"title":"铸造超级双相耐腐蚀钢的热变形建模","authors":"S. V. Rushchits,&nbsp;N. A. Shaburova,&nbsp;V. V. Sedukhin,&nbsp;A. M. Akhmed’yanov,&nbsp;S. P. Samoilov,&nbsp;A. N. Anikeev,&nbsp;I. V. Chumanov","doi":"10.1134/S0036029523120315","DOIUrl":null,"url":null,"abstract":"<p>The deformation behavior of cast super duplex steel is studied in the temperature range 1100–1250°C and the strain rate range 0.1–10 s<sup>–1</sup>. Hot deformation is performed by uniaxial compression of cylindrical specimens on a Gleeble 3800 simulator of thermomechanical processes. The flow stresses are shown to decrease with increasing temperature and decreasing strain rate in accordance with a change in the Zener–Hollomon parameter of the temperature–rate deformation conditions. The shape of the flow curves indicates that hot deformation is accompanied by intense dynamic softening, as a result of which the flow stresses decrease or remain unchanged after reaching peak values. Under all hot deformation conditions, ferrite acquires a dynamically recrystallized structure. At the lowest deformation temperature (1100°C) and relatively high strain rates (1–10 s<sup>–1</sup>), the mechanism of austenite softening is dynamic recovery. A decrease in the strain rate or an increase in the deformation temperature causes partial dynamic recrystallization of austenite. Under similar deformation conditions, the plastic flow stress of the steel under study is significantly higher than that in standard duplex stainless steels. When analyzing the peak flow stresses, we determined the effective hot deformation activation energy (<i>Q</i> = 501.31 kJ/mol) required for calculating the Zener–Hollomon parameter. An expression for describing the peak flow stress is obtained in the form of a hyperbolic function of the Zener–Hollomon parameter. This expression describes the experimental data array with a high accuracy and can be used to estimate the required energy–force parameters of forging and rolling equipment. A comparative estimation of the hot ductility of the super duplex steel is performed by finding the strain corresponding to the appearance of the first macrocracks on the specimen surface. At a strain rate of 10 s<sup>–1</sup> (which is characteristic of hot forging processes), the safest deformation temperature range of the steel is shown to be 1150–1250°C, in which austenite undergoes partial dynamic recrystallization reducing the risks of cracking.</p>","PeriodicalId":769,"journal":{"name":"Russian Metallurgy (Metally)","volume":null,"pages":null},"PeriodicalIF":0.4000,"publicationDate":"2024-03-19","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Modeling of the Hot Deformation of Cast Super Duplex Corrosion-Resistant Steel\",\"authors\":\"S. V. Rushchits,&nbsp;N. A. Shaburova,&nbsp;V. V. Sedukhin,&nbsp;A. M. Akhmed’yanov,&nbsp;S. P. Samoilov,&nbsp;A. N. Anikeev,&nbsp;I. V. Chumanov\",\"doi\":\"10.1134/S0036029523120315\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<p>The deformation behavior of cast super duplex steel is studied in the temperature range 1100–1250°C and the strain rate range 0.1–10 s<sup>–1</sup>. Hot deformation is performed by uniaxial compression of cylindrical specimens on a Gleeble 3800 simulator of thermomechanical processes. The flow stresses are shown to decrease with increasing temperature and decreasing strain rate in accordance with a change in the Zener–Hollomon parameter of the temperature–rate deformation conditions. The shape of the flow curves indicates that hot deformation is accompanied by intense dynamic softening, as a result of which the flow stresses decrease or remain unchanged after reaching peak values. Under all hot deformation conditions, ferrite acquires a dynamically recrystallized structure. At the lowest deformation temperature (1100°C) and relatively high strain rates (1–10 s<sup>–1</sup>), the mechanism of austenite softening is dynamic recovery. A decrease in the strain rate or an increase in the deformation temperature causes partial dynamic recrystallization of austenite. Under similar deformation conditions, the plastic flow stress of the steel under study is significantly higher than that in standard duplex stainless steels. When analyzing the peak flow stresses, we determined the effective hot deformation activation energy (<i>Q</i> = 501.31 kJ/mol) required for calculating the Zener–Hollomon parameter. An expression for describing the peak flow stress is obtained in the form of a hyperbolic function of the Zener–Hollomon parameter. This expression describes the experimental data array with a high accuracy and can be used to estimate the required energy–force parameters of forging and rolling equipment. A comparative estimation of the hot ductility of the super duplex steel is performed by finding the strain corresponding to the appearance of the first macrocracks on the specimen surface. At a strain rate of 10 s<sup>–1</sup> (which is characteristic of hot forging processes), the safest deformation temperature range of the steel is shown to be 1150–1250°C, in which austenite undergoes partial dynamic recrystallization reducing the risks of cracking.</p>\",\"PeriodicalId\":769,\"journal\":{\"name\":\"Russian Metallurgy (Metally)\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":0.4000,\"publicationDate\":\"2024-03-19\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Russian Metallurgy (Metally)\",\"FirstCategoryId\":\"5\",\"ListUrlMain\":\"https://link.springer.com/article/10.1134/S0036029523120315\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q4\",\"JCRName\":\"METALLURGY & METALLURGICAL ENGINEERING\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Russian Metallurgy (Metally)","FirstCategoryId":"5","ListUrlMain":"https://link.springer.com/article/10.1134/S0036029523120315","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q4","JCRName":"METALLURGY & METALLURGICAL ENGINEERING","Score":null,"Total":0}
引用次数: 0

摘要

研究了铸造超级双相钢在温度范围 1100-1250°C 和应变速率范围 0.1-10 s-1 下的变形行为。热变形是通过在 Gleeble 3800 热机械过程模拟器上对圆柱形试样进行单轴压缩来实现的。结果表明,随着温度的升高和应变速率的减小,流动应力随温度-速率变形条件下齐纳-霍洛蒙参数的变化而减小。流动曲线的形状表明,热变形伴随着强烈的动态软化,因此流动应力在达到峰值后会降低或保持不变。在所有热变形条件下,铁素体都获得了动态再结晶结构。在最低变形温度(1100°C)和相对较高的应变速率(1-10 s-1)下,奥氏体软化的机制是动态恢复。应变速率的降低或变形温度的升高会导致奥氏体部分动态再结晶。在类似的变形条件下,所研究钢材的塑性流动应力明显高于标准双相不锈钢。在分析峰值流动应力时,我们确定了计算齐纳-霍洛蒙参数所需的有效热变形活化能(Q = 501.31 kJ/mol)。以齐纳-霍洛蒙参数的双曲线函数形式得到了描述峰值流动应力的表达式。该表达式对实验数据阵列进行了高精度描述,可用于估算锻造和轧制设备所需的能量-力参数。通过找出试样表面出现第一条大裂纹时的相应应变,对超级双相钢的热延展性进行了比较估算。在应变速率为 10 s-1 时(这是热锻工艺的特征),钢的最安全变形温度范围为 1150-1250°C,在此温度范围内奥氏体会发生部分动态再结晶,从而降低开裂风险。
本文章由计算机程序翻译,如有差异,请以英文原文为准。

摘要图片

查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
Modeling of the Hot Deformation of Cast Super Duplex Corrosion-Resistant Steel

The deformation behavior of cast super duplex steel is studied in the temperature range 1100–1250°C and the strain rate range 0.1–10 s–1. Hot deformation is performed by uniaxial compression of cylindrical specimens on a Gleeble 3800 simulator of thermomechanical processes. The flow stresses are shown to decrease with increasing temperature and decreasing strain rate in accordance with a change in the Zener–Hollomon parameter of the temperature–rate deformation conditions. The shape of the flow curves indicates that hot deformation is accompanied by intense dynamic softening, as a result of which the flow stresses decrease or remain unchanged after reaching peak values. Under all hot deformation conditions, ferrite acquires a dynamically recrystallized structure. At the lowest deformation temperature (1100°C) and relatively high strain rates (1–10 s–1), the mechanism of austenite softening is dynamic recovery. A decrease in the strain rate or an increase in the deformation temperature causes partial dynamic recrystallization of austenite. Under similar deformation conditions, the plastic flow stress of the steel under study is significantly higher than that in standard duplex stainless steels. When analyzing the peak flow stresses, we determined the effective hot deformation activation energy (Q = 501.31 kJ/mol) required for calculating the Zener–Hollomon parameter. An expression for describing the peak flow stress is obtained in the form of a hyperbolic function of the Zener–Hollomon parameter. This expression describes the experimental data array with a high accuracy and can be used to estimate the required energy–force parameters of forging and rolling equipment. A comparative estimation of the hot ductility of the super duplex steel is performed by finding the strain corresponding to the appearance of the first macrocracks on the specimen surface. At a strain rate of 10 s–1 (which is characteristic of hot forging processes), the safest deformation temperature range of the steel is shown to be 1150–1250°C, in which austenite undergoes partial dynamic recrystallization reducing the risks of cracking.

求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
Russian Metallurgy (Metally)
Russian Metallurgy (Metally) METALLURGY & METALLURGICAL ENGINEERING-
CiteScore
0.70
自引率
25.00%
发文量
140
期刊介绍: Russian Metallurgy (Metally)  publishes results of original experimental and theoretical research in the form of reviews and regular articles devoted to topical problems of metallurgy, physical metallurgy, and treatment of ferrous, nonferrous, rare, and other metals and alloys, intermetallic compounds, and metallic composite materials. The journal focuses on physicochemical properties of metallurgical materials (ores, slags, matters, and melts of metals and alloys); physicochemical processes (thermodynamics and kinetics of pyrometallurgical, hydrometallurgical, electrochemical, and other processes); theoretical metallurgy; metal forming; thermoplastic and thermochemical treatment; computation and experimental determination of phase diagrams and thermokinetic diagrams; mechanisms and kinetics of phase transitions in metallic materials; relations between the chemical composition, phase and structural states of materials and their physicochemical and service properties; interaction between metallic materials and external media; and effects of radiation on these materials.
期刊最新文献
Phase States in the Li–Mn–Eu–O System Combined Deoxidation of Fe–Ni Melts by Manganese and Aluminum The Influence of Various Methods of Mechanical Actions on Magnetic Properties and Energy Losses during Magnetization Reversal in Soft Magnetic Ferromagnets The Chlorination Kinetics of Zirconium Dioxide Mixed with Carbon-Containing Material Kinetics and Thermodynamics of Iron(III) Ion Removal from Aqueous Solutions by Dowex G-26(H) Resin
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1