Xi Changfeng, Qi Zongyao, Liu Tong, Z. Yunjun, Zhao Fang, Qingsen Yu, D. Shen, Li Xiuluan
{"title":"蒸汽驱后CO2辅助蒸汽驱技术——以新疆油田J6区块为例","authors":"Xi Changfeng, Qi Zongyao, Liu Tong, Z. Yunjun, Zhao Fang, Qingsen Yu, D. Shen, Li Xiuluan","doi":"10.2118/196767-ms","DOIUrl":null,"url":null,"abstract":"\n Currently Block J6 is in the later stage of steam flooding after 27 years’ steam injection, its recovery factor is about 50%, and the water cut is more than 95%. Particularly, the present steam oil ratio is about 12 m3(CWE)/t which has reached the economic limit and is in ineffective development. Cores from four post steam flooding drilling wells show that only top 2-3m of the total 25-30m pay zone has a steam chamber which is the main steam channel and its residual oil saturation is about 20%, the other 22-27m pay zone is displaced by hot water and its oil saturation is 40-55%. A 3D physical simulation show the conventional steam flooding with full interval perforation quickly broke through from the top of reservoir, and the steam oil ratio rose rapidly from 5 m3(CWE)/t to 10 m3(CWE)/t. The recovery factor was only 20.1% at the time of steam breakthrough, and then it was in the phase of high steam oil ratio for a long time. During CO2 assisted steam flooding the whole perforated producer is switched into a low half perforated well, and the recovery factor increases from 20.1% to 81.1%, the steam oil ratio is 3.3m3(CWE)/t. There are three characteristics in CO2 assisted steam flooding stage, firstly there is a steam and CO2 assisted gravity drainage mode, steam chamber expands from the top 2-3cm to the total 20cm oil layer. Secondly, there is a stable emulsion foam oil, its water cut is 60-70%, CO2 liquid ratio is about 5:1 Sm3/t, CO2 is a kind of dispersed bubble so it is much more than the dissolved CO2 liquid ratio 2:1 Sm3/t. Thirdly, CO2 lows the heatloss to overburden and keeps the formation pressure. The calculation shows that the heat loss can be reduced by more than 10% in the top layer. A pilot test including 9 well patterns(49 wells) has been established, and its recovery factor will be up to 75%, and the steam oil ratio will up to 2 m3(CWE)/t, a good production performance is predicted optimistically.","PeriodicalId":10977,"journal":{"name":"Day 2 Wed, October 23, 2019","volume":null,"pages":null},"PeriodicalIF":0.0000,"publicationDate":"2019-10-22","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"1","resultStr":"{\"title\":\"CO2 Assisted Steam Flooding Technology after Steam Flooding - A Case Study in Block J6 of Xinjiang Oilfield\",\"authors\":\"Xi Changfeng, Qi Zongyao, Liu Tong, Z. Yunjun, Zhao Fang, Qingsen Yu, D. Shen, Li Xiuluan\",\"doi\":\"10.2118/196767-ms\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"\\n Currently Block J6 is in the later stage of steam flooding after 27 years’ steam injection, its recovery factor is about 50%, and the water cut is more than 95%. Particularly, the present steam oil ratio is about 12 m3(CWE)/t which has reached the economic limit and is in ineffective development. Cores from four post steam flooding drilling wells show that only top 2-3m of the total 25-30m pay zone has a steam chamber which is the main steam channel and its residual oil saturation is about 20%, the other 22-27m pay zone is displaced by hot water and its oil saturation is 40-55%. A 3D physical simulation show the conventional steam flooding with full interval perforation quickly broke through from the top of reservoir, and the steam oil ratio rose rapidly from 5 m3(CWE)/t to 10 m3(CWE)/t. The recovery factor was only 20.1% at the time of steam breakthrough, and then it was in the phase of high steam oil ratio for a long time. During CO2 assisted steam flooding the whole perforated producer is switched into a low half perforated well, and the recovery factor increases from 20.1% to 81.1%, the steam oil ratio is 3.3m3(CWE)/t. There are three characteristics in CO2 assisted steam flooding stage, firstly there is a steam and CO2 assisted gravity drainage mode, steam chamber expands from the top 2-3cm to the total 20cm oil layer. Secondly, there is a stable emulsion foam oil, its water cut is 60-70%, CO2 liquid ratio is about 5:1 Sm3/t, CO2 is a kind of dispersed bubble so it is much more than the dissolved CO2 liquid ratio 2:1 Sm3/t. Thirdly, CO2 lows the heatloss to overburden and keeps the formation pressure. The calculation shows that the heat loss can be reduced by more than 10% in the top layer. A pilot test including 9 well patterns(49 wells) has been established, and its recovery factor will be up to 75%, and the steam oil ratio will up to 2 m3(CWE)/t, a good production performance is predicted optimistically.\",\"PeriodicalId\":10977,\"journal\":{\"name\":\"Day 2 Wed, October 23, 2019\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":0.0000,\"publicationDate\":\"2019-10-22\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"1\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Day 2 Wed, October 23, 2019\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.2118/196767-ms\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"\",\"JCRName\":\"\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Day 2 Wed, October 23, 2019","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.2118/196767-ms","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"","JCRName":"","Score":null,"Total":0}
CO2 Assisted Steam Flooding Technology after Steam Flooding - A Case Study in Block J6 of Xinjiang Oilfield
Currently Block J6 is in the later stage of steam flooding after 27 years’ steam injection, its recovery factor is about 50%, and the water cut is more than 95%. Particularly, the present steam oil ratio is about 12 m3(CWE)/t which has reached the economic limit and is in ineffective development. Cores from four post steam flooding drilling wells show that only top 2-3m of the total 25-30m pay zone has a steam chamber which is the main steam channel and its residual oil saturation is about 20%, the other 22-27m pay zone is displaced by hot water and its oil saturation is 40-55%. A 3D physical simulation show the conventional steam flooding with full interval perforation quickly broke through from the top of reservoir, and the steam oil ratio rose rapidly from 5 m3(CWE)/t to 10 m3(CWE)/t. The recovery factor was only 20.1% at the time of steam breakthrough, and then it was in the phase of high steam oil ratio for a long time. During CO2 assisted steam flooding the whole perforated producer is switched into a low half perforated well, and the recovery factor increases from 20.1% to 81.1%, the steam oil ratio is 3.3m3(CWE)/t. There are three characteristics in CO2 assisted steam flooding stage, firstly there is a steam and CO2 assisted gravity drainage mode, steam chamber expands from the top 2-3cm to the total 20cm oil layer. Secondly, there is a stable emulsion foam oil, its water cut is 60-70%, CO2 liquid ratio is about 5:1 Sm3/t, CO2 is a kind of dispersed bubble so it is much more than the dissolved CO2 liquid ratio 2:1 Sm3/t. Thirdly, CO2 lows the heatloss to overburden and keeps the formation pressure. The calculation shows that the heat loss can be reduced by more than 10% in the top layer. A pilot test including 9 well patterns(49 wells) has been established, and its recovery factor will be up to 75%, and the steam oil ratio will up to 2 m3(CWE)/t, a good production performance is predicted optimistically.