{"title":"Directed energy deposition of PH 13–8 Mo stainless steel: microstructure and mechanical property analysis","authors":"","doi":"10.1007/s00170-024-13411-3","DOIUrl":null,"url":null,"abstract":"<h3>Abstract</h3> <p>Laser metal deposition (LMD) is of the directed energy deposition (DED) process which is widely used for producing large-scale, dense, and functional parts in the field of additive manufacturing (AM). This research work investigates the microstructure and mechanical properties of PH 13–8 Mo martensitic stainless-steel parts produced via LMD. The workshop trials were conducted using an LMD system collaborated with a robotic arm to deposit single-track thin walls and horizontal blocks. The microstructural characteristics of the additively manufactured parts were analyzed using an optical microscope. The mechanical properties were evaluated through hardness measurements and uniaxial tensile tests. The influence of energy density and powder deposition density on the characteristic geometry of straight walls was also investigated. The microstructural analysis showed that the microstructure consisted of columnar dendrites that grew epitaxially from the substrate, with primary austenite cells containing intercellular ferrite and martensite laths that were roughly parallel with the retained austenite. When the energy density increased from 43 to 86 J/mm<sup>2</sup> (a doubling of energy density), there was an increase in secondary dendritic arm spacing (SDAS) by approximately 250% in the first layer and approximately 90% in the top layer. The difference in SDAS change between the first and top layers can be attributed to the difference in cooling rates experienced by each layer during the additive manufacturing process. Increasing powder deposition density from 0.5 to 1 g/min results in a decrease in porosity from 3% to less than 1% and an increase in strength from 800 to over 1000 MPa. The hardness of the deposits was found to range from 300 to 400 HV. This variation in hardness can be attributed to differences in microstructure resulting from changes in cooling rates at different heights.</p>","PeriodicalId":50345,"journal":{"name":"International Journal of Advanced Manufacturing Technology","volume":"37 1","pages":""},"PeriodicalIF":2.9000,"publicationDate":"2024-03-14","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"International Journal of Advanced Manufacturing Technology","FirstCategoryId":"5","ListUrlMain":"https://doi.org/10.1007/s00170-024-13411-3","RegionNum":3,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q2","JCRName":"AUTOMATION & CONTROL SYSTEMS","Score":null,"Total":0}
引用次数: 0
Abstract
Laser metal deposition (LMD) is of the directed energy deposition (DED) process which is widely used for producing large-scale, dense, and functional parts in the field of additive manufacturing (AM). This research work investigates the microstructure and mechanical properties of PH 13–8 Mo martensitic stainless-steel parts produced via LMD. The workshop trials were conducted using an LMD system collaborated with a robotic arm to deposit single-track thin walls and horizontal blocks. The microstructural characteristics of the additively manufactured parts were analyzed using an optical microscope. The mechanical properties were evaluated through hardness measurements and uniaxial tensile tests. The influence of energy density and powder deposition density on the characteristic geometry of straight walls was also investigated. The microstructural analysis showed that the microstructure consisted of columnar dendrites that grew epitaxially from the substrate, with primary austenite cells containing intercellular ferrite and martensite laths that were roughly parallel with the retained austenite. When the energy density increased from 43 to 86 J/mm2 (a doubling of energy density), there was an increase in secondary dendritic arm spacing (SDAS) by approximately 250% in the first layer and approximately 90% in the top layer. The difference in SDAS change between the first and top layers can be attributed to the difference in cooling rates experienced by each layer during the additive manufacturing process. Increasing powder deposition density from 0.5 to 1 g/min results in a decrease in porosity from 3% to less than 1% and an increase in strength from 800 to over 1000 MPa. The hardness of the deposits was found to range from 300 to 400 HV. This variation in hardness can be attributed to differences in microstructure resulting from changes in cooling rates at different heights.
期刊介绍：
The International Journal of Advanced Manufacturing Technology bridges the gap between pure research journals and the more practical publications on advanced manufacturing and systems. It therefore provides an outstanding forum for papers covering applications-based research topics relevant to manufacturing processes, machines and process integration.
京公网安备 11010802042870号
京ICP备2023020795号-1
分享
求助内容：
应助结果提醒方式：
扫码关注我们
