Influence of Moisture Content on Cutting Parameters and Fracture Characteristics of Spruce and Oak Wood

IF 0.7 4区 农林科学 Q4 MATERIALS SCIENCE, PAPER & WOOD Drvna Industrija Pub Date : 2022-07-15 DOI:10.5552/drvind.2022.0026
Luďka Hanincová, J. Procházka, V. Novák, Z. Kopecký
{"title":"Influence of Moisture Content on Cutting Parameters and Fracture Characteristics of Spruce and Oak Wood","authors":"Luďka Hanincová, J. Procházka, V. Novák, Z. Kopecký","doi":"10.5552/drvind.2022.0026","DOIUrl":null,"url":null,"abstract":"The objective of this study was to determine the effect of the moisture content on cutting parameters and fracture characteristics of spruce and oak wood. Samples of Norway spruce (Picea abies (L.) H. Karst.) and English oak (Quercus robur L.) were dried to required moisture content and then used for the machinability test on circular sawblade machine. Results indicate that cutting force and feed force increase with increasing moisture content up to the fiber saturation point (FSP). When the moisture content increases above the FSP, the minimum values of cutting and feed force are achieved. Based on performed experiments, the fracture toughness and shear yield strength were derived. Fracture toughness decreases with increasing moisture content. The minimum values of fracture toughness are achieved at the moisture content level above the FSP. Shear yield strength decreases linearly with increasing moisture content: the decrease is up to 17 % compared to samples with moisture content at the FSP. Based on calculated results, the influence of moisture content and wood species on cutting and fracture characteristics was discussed.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":null,"pages":null},"PeriodicalIF":0.7000,"publicationDate":"2022-07-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"1","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Drvna Industrija","FirstCategoryId":"88","ListUrlMain":"https://doi.org/10.5552/drvind.2022.0026","RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q4","JCRName":"MATERIALS SCIENCE, PAPER & WOOD","Score":null,"Total":0}
引用次数: 1

Abstract

The objective of this study was to determine the effect of the moisture content on cutting parameters and fracture characteristics of spruce and oak wood. Samples of Norway spruce (Picea abies (L.) H. Karst.) and English oak (Quercus robur L.) were dried to required moisture content and then used for the machinability test on circular sawblade machine. Results indicate that cutting force and feed force increase with increasing moisture content up to the fiber saturation point (FSP). When the moisture content increases above the FSP, the minimum values of cutting and feed force are achieved. Based on performed experiments, the fracture toughness and shear yield strength were derived. Fracture toughness decreases with increasing moisture content. The minimum values of fracture toughness are achieved at the moisture content level above the FSP. Shear yield strength decreases linearly with increasing moisture content: the decrease is up to 17 % compared to samples with moisture content at the FSP. Based on calculated results, the influence of moisture content and wood species on cutting and fracture characteristics was discussed.
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
含水率对云杉和橡木切削参数及断裂特性的影响
本研究的目的是确定水分含量对云杉和橡树木材的切割参数和断裂特性的影响。挪威云杉(Picea abies (L.))样品(H. Karst.)和英国橡木(Quercus robur L.)干燥至所需含水量,然后在圆锯片机上进行可加工性试验。结果表明,在纤维饱和点(FSP)前,切削力和进给力随含水率的增加而增大。当含水率大于FSP时,切削力和进给力达到最小值。在实验的基础上,推导了断裂韧性和抗剪屈服强度。断裂韧性随含水率的增加而降低。断裂韧性的最小值是在FSP以上的含水率水平上实现的。剪切屈服强度随着含水率的增加而线性降低:与FSP含水率的样品相比,降低幅度高达17%。根据计算结果,讨论了含水率和木材种类对切割和断裂特性的影响。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 去求助
来源期刊
Drvna Industrija
Drvna Industrija MATERIALS SCIENCE, PAPER & WOOD-
CiteScore
1.80
自引率
9.10%
发文量
32
审稿时长
>12 weeks
期刊介绍: "Drvna industrija" ("Wood Industry") journal publishes original scientific and review papers, short notes, professional papers, conference papers, reports, professional information, bibliographical and survey articles and general notes relating to the forestry exploitation, biology, chemistry, physics and technology of wood, pulp and paper and wood components, including production, management and marketing aspects in the woodworking industry.
期刊最新文献
Water Permeability and Adhesion Strength of Bio-based Coating Applied on Wood Usporedna studija dimenzijske stabilnosti i biološke trajnosti kemijski i toplinski modificirane topolovine Assessment of Condition of Wooden Mill in Kovačevići Area in Bosnia and Herzegovina Efficiency Assessment Based on Data Envelopment Analysis for Occupational Accidents and Diseases in Furniture Industry of Turkey Timber Strength Grading as Necessary Basis for Structural Design in Ex-YU Region
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1