Study on Changes in Hardness and Wear Resistance of 3D Printed Ti6Al4V with Heat Treatment Temperature

Q3 Engineering Tribology in Industry Pub Date : 2023-03-15 DOI:10.24874/ti.1421.12.22.02
Nay Win Khun, Wei Quan Toh, E. Liu
{"title":"Study on Changes in Hardness and Wear Resistance of 3D Printed Ti6Al4V with Heat Treatment Temperature","authors":"Nay Win Khun, Wei Quan Toh, E. Liu","doi":"10.24874/ti.1421.12.22.02","DOIUrl":null,"url":null,"abstract":"The hardness and specific wear rate of 3 dimensionally (3D) printed Ti6Al4V specimens were studied with respect to heat treatment temperature (HTT) in a range of 400-800 °C. Increasing the HTT from 400 °C to 500 °C promoted the hardness of the printed specimen while its decreased hardness associated with a further increase in the HTT to 800 °C was observed. Since higher wear resistance was the result of higher hardness, the trend of specific wear rate versus HTT of the printed specimen was opposite to that of its hardness versus HTT. The highest hardness and lowest wear of the printed specimen were therefore found at the HTT of 500 °C.","PeriodicalId":23320,"journal":{"name":"Tribology in Industry","volume":null,"pages":null},"PeriodicalIF":0.0000,"publicationDate":"2023-03-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"1","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"Tribology in Industry","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.24874/ti.1421.12.22.02","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q3","JCRName":"Engineering","Score":null,"Total":0}
引用次数: 1

Abstract

The hardness and specific wear rate of 3 dimensionally (3D) printed Ti6Al4V specimens were studied with respect to heat treatment temperature (HTT) in a range of 400-800 °C. Increasing the HTT from 400 °C to 500 °C promoted the hardness of the printed specimen while its decreased hardness associated with a further increase in the HTT to 800 °C was observed. Since higher wear resistance was the result of higher hardness, the trend of specific wear rate versus HTT of the printed specimen was opposite to that of its hardness versus HTT. The highest hardness and lowest wear of the printed specimen were therefore found at the HTT of 500 °C.
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
三维打印Ti6Al4V的硬度和耐磨性随热处理温度变化的研究
研究了在400-800°C范围内,三维(3D)打印的Ti6Al4V试样的硬度和比磨损率与热处理温度(HTT)的关系。将HTT从400°C增加到500°C提高了印刷样品的硬度,同时观察到其硬度降低与HTT进一步增加到800°C有关。由于较高的耐磨性是较高硬度的结果,因此印刷试样的比磨损率相对于HTT的趋势与其硬度相对于HTT相反。因此,在500°C的HTT下发现印刷样品的最高硬度和最低磨损。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 去求助
来源期刊
Tribology in Industry
Tribology in Industry Engineering-Mechanical Engineering
CiteScore
2.80
自引率
0.00%
发文量
47
审稿时长
8 weeks
期刊介绍: he aim of Tribology in Industry journal is to publish quality experimental and theoretical research papers in fields of the science of friction, wear and lubrication and any closely related fields. The scope includes all aspects of materials science, surface science, applied physics and mechanical engineering which relate directly to the subjects of wear and friction. Topical areas include, but are not limited to: Friction, Wear, Lubricants, Surface characterization, Surface engineering, Nanotribology, Contact mechanics, Coatings, Alloys, Composites, Tribological design, Biotribology, Green Tribology.
期刊最新文献
Investigation on Solid Particle Erosion Performance of Aluminum Alloy Materials for Leading-Edge Slat Friction and Wear Characteristics of Bio-Lubricants Containing Clove Oil as Antioxidant Study of the Influence of Coating Roughness on the Properties and Wear Resistance of Electrospark Deposited Ti6Al4V Titanium Alloy Parametric Design Optimization of Convergent Textured Thrust Bearing in THD Behaviour Effective Strains Determination in Continuous Constrained Double Bending with Active Friction Forces
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1