实验研究了增强粘弹性聚合物驱并进一步提高剩余油饱和度的新物理机制

IF 2.6 Q3 ENERGY & FUELS Upstream Oil and Gas Technology Pub Date : 2021-02-01 DOI:10.1016/j.upstre.2020.100026
Md Irfan , Karl D. Stephen , Christopher P. Lenn
{"title":"实验研究了增强粘弹性聚合物驱并进一步提高剩余油饱和度的新物理机制","authors":"Md Irfan ,&nbsp;Karl D. Stephen ,&nbsp;Christopher P. Lenn","doi":"10.1016/j.upstre.2020.100026","DOIUrl":null,"url":null,"abstract":"<div><p><span><span>This study uses a combination of shear rheometry<span> and core-flooding using viscoelastic polymers to understand better the enhanced oil sweep efficiency after residual oil saturation is achieved by conventional water-flood. This work addresses the question of anomalous (enhanced) </span></span>desaturation<span> of oil by water-flooding using polymer and which has been widely reported since 2008. A mechanism to explain the enhanced desaturation is developed. Berea sandstone was saturated with synthetic oil (34mPa.s @ </span></span><span><math><msup><mn>20</mn><mn>0</mn></msup></math></span> C) at set reservoir conditions (2000 psi, <span><math><msup><mn>90</mn><mn>0</mn></msup></math></span><span> C). It was water-flooded from initial oil saturation (</span><span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>i</mi></mrow></msub><mo>=</mo><mn>76.21</mn></mrow></math></span> %, 47.5 ml) to residual oil saturation (<span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mi>w</mi></mrow></msub><mo>=</mo><mn>40.43</mn></mrow></math></span><span> %, 25.2 ml) where oil cut was zero using brine (33390 ppm). The core was subject to further flooding using inelastic Newtonian 85 wt % Glycerol flooding until zero oil cut (</span><span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mi>g</mi><mi>l</mi><mi>y</mi></mrow></msub><mo>=</mo><mn>36.90</mn></mrow></math></span><span> %, 23.0 ml), followed by viscous Non-Newtonian 1720 ppm Xanthan Gum flooding (</span><span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mi>x</mi></mrow></msub><mo>=</mo><mn>34.33</mn></mrow></math></span> %, 21.4 ml), followed by 6000 ppm viscoelastic FLOPAAM 3230 (<span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mn>3230</mn></mrow></msub><mo>=</mo><mn>34.33</mn></mrow></math></span> %, 21.4 ml, zero oil cut) and ended by 2000 ppm FLOCOMB 6525 (<span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mn>6525</mn></mrow></msub><mo>=</mo><mn>33.21</mn></mrow></math></span><span><span> %, 20.7 ml). It was found an additional 3.27% OOIP was recovered by the elastic </span>turbulence effect<span> of high Mw viscoelastic polymer-flooding below critical Capillary number, having the Deborah number, </span></span><span><math><mrow><msub><mi>N</mi><mrow><mi>D</mi><mi>e</mi></mrow></msub><mo>=</mo><mn>2.13</mn></mrow></math></span><span>. Since the late 1960s, EOR researchers have developed different continuum and pore-scale viscoelastic models for quantifying the viscoelastic polymer-flooding effects on </span><span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span>. From the literature, research articles conclude that <span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span><span><span> reduction depends upon the flux rate as well as on reservoir </span>wettability<span>, brine salinity<span>, reservoir permeability<span>, polymer elasticity, Mw of viscoelastic polymer and oil viscosity. We have come to the conclusion in this paper that despite these noteworthy </span></span></span></span><span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span> reduction explanations, the mechanism of quantified <span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span> reduction by viscoelastic effect is as yet an unresolved mechanism that requires further investigation. We conclude that the proposed elastic turbulence mechanism has played an important role in the occurrence of increased pore-level induced pressure fluctuations, which in turn increases velocity rate fluctuations and hence additional desaturation of immobile residual oil.</p></div>","PeriodicalId":101264,"journal":{"name":"Upstream Oil and Gas Technology","volume":"6 ","pages":"Article 100026"},"PeriodicalIF":2.6000,"publicationDate":"2021-02-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"https://sci-hub-pdf.com/10.1016/j.upstre.2020.100026","citationCount":"4","resultStr":"{\"title\":\"An experimental study to investigate novel physical mechanisms that enhance viscoelastic polymer flooding and further increase desaturation of residual oil saturation\",\"authors\":\"Md Irfan ,&nbsp;Karl D. Stephen ,&nbsp;Christopher P. Lenn\",\"doi\":\"10.1016/j.upstre.2020.100026\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<div><p><span><span>This study uses a combination of shear rheometry<span> and core-flooding using viscoelastic polymers to understand better the enhanced oil sweep efficiency after residual oil saturation is achieved by conventional water-flood. This work addresses the question of anomalous (enhanced) </span></span>desaturation<span> of oil by water-flooding using polymer and which has been widely reported since 2008. A mechanism to explain the enhanced desaturation is developed. Berea sandstone was saturated with synthetic oil (34mPa.s @ </span></span><span><math><msup><mn>20</mn><mn>0</mn></msup></math></span> C) at set reservoir conditions (2000 psi, <span><math><msup><mn>90</mn><mn>0</mn></msup></math></span><span> C). It was water-flooded from initial oil saturation (</span><span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>i</mi></mrow></msub><mo>=</mo><mn>76.21</mn></mrow></math></span> %, 47.5 ml) to residual oil saturation (<span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mi>w</mi></mrow></msub><mo>=</mo><mn>40.43</mn></mrow></math></span><span> %, 25.2 ml) where oil cut was zero using brine (33390 ppm). The core was subject to further flooding using inelastic Newtonian 85 wt % Glycerol flooding until zero oil cut (</span><span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mi>g</mi><mi>l</mi><mi>y</mi></mrow></msub><mo>=</mo><mn>36.90</mn></mrow></math></span><span> %, 23.0 ml), followed by viscous Non-Newtonian 1720 ppm Xanthan Gum flooding (</span><span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mi>x</mi></mrow></msub><mo>=</mo><mn>34.33</mn></mrow></math></span> %, 21.4 ml), followed by 6000 ppm viscoelastic FLOPAAM 3230 (<span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mn>3230</mn></mrow></msub><mo>=</mo><mn>34.33</mn></mrow></math></span> %, 21.4 ml, zero oil cut) and ended by 2000 ppm FLOCOMB 6525 (<span><math><mrow><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi><mn>6525</mn></mrow></msub><mo>=</mo><mn>33.21</mn></mrow></math></span><span><span> %, 20.7 ml). It was found an additional 3.27% OOIP was recovered by the elastic </span>turbulence effect<span> of high Mw viscoelastic polymer-flooding below critical Capillary number, having the Deborah number, </span></span><span><math><mrow><msub><mi>N</mi><mrow><mi>D</mi><mi>e</mi></mrow></msub><mo>=</mo><mn>2.13</mn></mrow></math></span><span>. Since the late 1960s, EOR researchers have developed different continuum and pore-scale viscoelastic models for quantifying the viscoelastic polymer-flooding effects on </span><span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span>. From the literature, research articles conclude that <span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span><span><span> reduction depends upon the flux rate as well as on reservoir </span>wettability<span>, brine salinity<span>, reservoir permeability<span>, polymer elasticity, Mw of viscoelastic polymer and oil viscosity. We have come to the conclusion in this paper that despite these noteworthy </span></span></span></span><span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span> reduction explanations, the mechanism of quantified <span><math><msub><mi>S</mi><mrow><mi>o</mi><mi>r</mi></mrow></msub></math></span> reduction by viscoelastic effect is as yet an unresolved mechanism that requires further investigation. We conclude that the proposed elastic turbulence mechanism has played an important role in the occurrence of increased pore-level induced pressure fluctuations, which in turn increases velocity rate fluctuations and hence additional desaturation of immobile residual oil.</p></div>\",\"PeriodicalId\":101264,\"journal\":{\"name\":\"Upstream Oil and Gas Technology\",\"volume\":\"6 \",\"pages\":\"Article 100026\"},\"PeriodicalIF\":2.6000,\"publicationDate\":\"2021-02-01\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"https://sci-hub-pdf.com/10.1016/j.upstre.2020.100026\",\"citationCount\":\"4\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Upstream Oil and Gas Technology\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://www.sciencedirect.com/science/article/pii/S2666260420300268\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q3\",\"JCRName\":\"ENERGY & FUELS\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Upstream Oil and Gas Technology","FirstCategoryId":"1085","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S2666260420300268","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q3","JCRName":"ENERGY & FUELS","Score":null,"Total":0}
引用次数: 4

摘要

该研究结合了剪切流变法和粘弹性聚合物岩心驱油技术,以更好地了解常规注水达到残余油饱和后的驱油效率。这项工作解决了自2008年以来广泛报道的聚合物水驱油异常(增强)脱饱和问题。提出了一种解释脱水增强的机制。Berea砂岩饱和合成油(34mPa)。在初始含油饱和度(Soi= 76.21%, 47.5 ml)至残余含油饱和度(Sorw= 40.43%, 25.2 ml),使用盐水(33390 ppm)时含油量为零。岩心使用非弹性牛顿85%甘油驱油进行进一步驱油,直到零含油(sorly = 36.90%, 23.0 ml),然后是粘性非牛顿1720 ppm黄原胶驱油(Sorx= 34.33%, 21.4 ml),然后是6000 ppm粘弹性FLOPAAM 3230 (Sor3230= 34.33%, 21.4 ml,零含油),最后是2000 ppm FLOCOMB 6525 (Sor6525= 33.21%, 20.7 ml)。结果表明,在临界毛细数以下,高Mw粘弹性聚合物驱的弹性湍流效应可额外回收3.27%的OOIP,其黛博拉数NDe=2.13。自20世纪60年代末以来,EOR研究人员开发了不同的连续统和孔隙尺度粘弹性模型,以量化粘弹性聚合物驱对Sor的影响。从文献中,研究文章得出结论,Sor的降低取决于通量速率以及储层润湿性、盐水盐度、储层渗透率、聚合物弹性、粘弹性聚合物的分子量和油粘度。我们在本文中得出的结论是,尽管有这些值得注意的减量解释,但通过粘弹性效应量化减量的机制仍是一个尚未解决的机制,需要进一步研究。我们得出结论,所提出的弹性湍流机制在孔隙水平诱导压力波动增加的发生中发挥了重要作用,这反过来又增加了速度波动,从而增加了不动剩余油的进一步去饱和。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
An experimental study to investigate novel physical mechanisms that enhance viscoelastic polymer flooding and further increase desaturation of residual oil saturation

This study uses a combination of shear rheometry and core-flooding using viscoelastic polymers to understand better the enhanced oil sweep efficiency after residual oil saturation is achieved by conventional water-flood. This work addresses the question of anomalous (enhanced) desaturation of oil by water-flooding using polymer and which has been widely reported since 2008. A mechanism to explain the enhanced desaturation is developed. Berea sandstone was saturated with synthetic oil (34mPa.s @ 200 C) at set reservoir conditions (2000 psi, 900 C). It was water-flooded from initial oil saturation (Soi=76.21 %, 47.5 ml) to residual oil saturation (Sorw=40.43 %, 25.2 ml) where oil cut was zero using brine (33390 ppm). The core was subject to further flooding using inelastic Newtonian 85 wt % Glycerol flooding until zero oil cut (Sorgly=36.90 %, 23.0 ml), followed by viscous Non-Newtonian 1720 ppm Xanthan Gum flooding (Sorx=34.33 %, 21.4 ml), followed by 6000 ppm viscoelastic FLOPAAM 3230 (Sor3230=34.33 %, 21.4 ml, zero oil cut) and ended by 2000 ppm FLOCOMB 6525 (Sor6525=33.21 %, 20.7 ml). It was found an additional 3.27% OOIP was recovered by the elastic turbulence effect of high Mw viscoelastic polymer-flooding below critical Capillary number, having the Deborah number, NDe=2.13. Since the late 1960s, EOR researchers have developed different continuum and pore-scale viscoelastic models for quantifying the viscoelastic polymer-flooding effects on Sor. From the literature, research articles conclude that Sor reduction depends upon the flux rate as well as on reservoir wettability, brine salinity, reservoir permeability, polymer elasticity, Mw of viscoelastic polymer and oil viscosity. We have come to the conclusion in this paper that despite these noteworthy Sor reduction explanations, the mechanism of quantified Sor reduction by viscoelastic effect is as yet an unresolved mechanism that requires further investigation. We conclude that the proposed elastic turbulence mechanism has played an important role in the occurrence of increased pore-level induced pressure fluctuations, which in turn increases velocity rate fluctuations and hence additional desaturation of immobile residual oil.

求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
CiteScore
5.50
自引率
0.00%
发文量
0
期刊最新文献
Dynamics of pump jacks with theories and experiments Well perforating—More than reservoir connection A new method for predicting casing wear in highly deviated wells using mud logging data Experimental investigation of bypassed-oil recovery in tight reservoir rock using a two-step CO2 soaking strategy: Effects of fracture geometry A Review of Modern Approaches of Digitalization in Oil and Gas Industry
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1