Igor Đukić, Juraj Jovanović, Ivica Župčić, Matija Jug
{"title":"用于过滤粗糙度信号的阈值傅立叶变换(FFT)表面滤波器","authors":"Igor Đukić, Juraj Jovanović, Ivica Župčić, Matija Jug","doi":"10.5552/drvind.2023.0088","DOIUrl":null,"url":null,"abstract":"The article presents the method for an objective determination of threshold value, needed for filtering out the anatomical roughness signal, with filter based on fast Fourier Transform (FFT), from surface roughness profile after machining. The method includes experimental preparation of solid wood surface by cutting in such a way to get a surface that can be considered to represent only anatomical roughness, with no other influence. Experiments were performed on radial cross section of solid oak wood (Quercus robur L.) so that the results could be compared with roughness profiles that were previously obtained in experiments after sawing with circular saw. From these samples and based on frequency analysis of anatomical roughness signals, the threshold value was determined to be 1.6 μm. The average value of Ra parameter of anatomical roughness for specimens of radial cross section of solid oak wood was 2.1 μm with standard deviation of 0.3 μm. The importance of choosing adequate sampling length in threshold determination, based on frequency analysis of anatomical roughness signal, was also established.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":null,"pages":null},"PeriodicalIF":0.7000,"publicationDate":"2023-09-29","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Kriterij za objektivno određivanje vrijednosti praga osjetljivosti pri filtriranju signala hrapavosti strojno obrađene površine masivnog drva filtrom utemeljenim na brzoj Fourierovoj transformaciji (FFT)\",\"authors\":\"Igor Đukić, Juraj Jovanović, Ivica Župčić, Matija Jug\",\"doi\":\"10.5552/drvind.2023.0088\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"The article presents the method for an objective determination of threshold value, needed for filtering out the anatomical roughness signal, with filter based on fast Fourier Transform (FFT), from surface roughness profile after machining. The method includes experimental preparation of solid wood surface by cutting in such a way to get a surface that can be considered to represent only anatomical roughness, with no other influence. Experiments were performed on radial cross section of solid oak wood (Quercus robur L.) so that the results could be compared with roughness profiles that were previously obtained in experiments after sawing with circular saw. From these samples and based on frequency analysis of anatomical roughness signals, the threshold value was determined to be 1.6 μm. The average value of Ra parameter of anatomical roughness for specimens of radial cross section of solid oak wood was 2.1 μm with standard deviation of 0.3 μm. The importance of choosing adequate sampling length in threshold determination, based on frequency analysis of anatomical roughness signal, was also established.\",\"PeriodicalId\":11427,\"journal\":{\"name\":\"Drvna Industrija\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":0.7000,\"publicationDate\":\"2023-09-29\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Drvna Industrija\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.5552/drvind.2023.0088\",\"RegionNum\":4,\"RegionCategory\":\"农林科学\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q4\",\"JCRName\":\"MATERIALS SCIENCE, PAPER & WOOD\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Drvna Industrija","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.5552/drvind.2023.0088","RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q4","JCRName":"MATERIALS SCIENCE, PAPER & WOOD","Score":null,"Total":0}
Kriterij za objektivno određivanje vrijednosti praga osjetljivosti pri filtriranju signala hrapavosti strojno obrađene površine masivnog drva filtrom utemeljenim na brzoj Fourierovoj transformaciji (FFT)
The article presents the method for an objective determination of threshold value, needed for filtering out the anatomical roughness signal, with filter based on fast Fourier Transform (FFT), from surface roughness profile after machining. The method includes experimental preparation of solid wood surface by cutting in such a way to get a surface that can be considered to represent only anatomical roughness, with no other influence. Experiments were performed on radial cross section of solid oak wood (Quercus robur L.) so that the results could be compared with roughness profiles that were previously obtained in experiments after sawing with circular saw. From these samples and based on frequency analysis of anatomical roughness signals, the threshold value was determined to be 1.6 μm. The average value of Ra parameter of anatomical roughness for specimens of radial cross section of solid oak wood was 2.1 μm with standard deviation of 0.3 μm. The importance of choosing adequate sampling length in threshold determination, based on frequency analysis of anatomical roughness signal, was also established.
期刊介绍:
"Drvna industrija" ("Wood Industry") journal publishes original scientific and review papers, short notes, professional papers, conference papers, reports, professional information, bibliographical and survey articles and general notes relating to the forestry exploitation, biology, chemistry, physics and technology of wood, pulp and paper and wood components, including production, management and marketing aspects in the woodworking industry.