利用多源超声波振动增强铝熔体中的颗粒分散:模拟与实验

IF 2.6 3区 材料科学 Q2 METALLURGY & METALLURGICAL ENGINEERING International Journal of Metalcasting Pub Date : 2024-08-06 DOI:10.1007/s40962-024-01419-0
Yeliang Zhu, Xiaogang Fang, Shulin Lv, Shusen Wu, Shifeng Luo, Siliang Yan, Jiguang Liu, Youwen Yang, Yiqing Chen
{"title":"利用多源超声波振动增强铝熔体中的颗粒分散:模拟与实验","authors":"Yeliang Zhu, Xiaogang Fang, Shulin Lv, Shusen Wu, Shifeng Luo, Siliang Yan, Jiguang Liu, Youwen Yang, Yiqing Chen","doi":"10.1007/s40962-024-01419-0","DOIUrl":null,"url":null,"abstract":"<p>Due to severe acoustic attenuation, the effectiveness of single-source ultrasonic vibration (SUV) in dispersing reinforcement particles within Al matrix composites is limited, particularly when dealing with high weight fractions. In this study, a short-spacing multi-source ultrasonic vibration (MUV) technique, specifically quad-source ultrasonic vibration (QUV), was introduced to prepare SiC<sub>p</sub>/A356 composites with a high weight fraction of 15wt.% SiC particles. The characteristic of acoustic streaming and the dispersion of particles were systematically investigated through numerical simulations and physical experiments. The results reveal that QUV mitigates acoustic attenuation and expands the potential cavitation region (exceeding the cavitation threshold of 1.1 MPa) compared to single-source ultrasonic vibration (SUV). The synergistic effect of multiple ultrasonic waves not only elevates cavitation intensity but also enriches the structures of acoustic streaming, significantly reducing agglomeration and improving the dispersion of SiC particles within the Al matrix. Without ultrasonic treatment, only a small proportion of SiC particles are embedded in the Al matrix, with an S<sub>SiC</sub>/S<sub>t</sub> ratio of merely 2.23%. However, as the number of ultrasonic sources increases, the agglomeration of SiC particles was relieved, and the resultant holes diminish. Remarkably, under QUV treatment, the holes in the composites virtually disappear, and the S<sub>SiC</sub>/S<sub>t</sub> ratio increases to 9.82%. Additionally, the composites exhibit superior mechanical properties, with a tensile strength of 200 MPa and an elongation of 7.0%, which are 10.5% and 38.5% higher than those achieved using SUV, respectively.</p>","PeriodicalId":14231,"journal":{"name":"International Journal of Metalcasting","volume":"95 1","pages":""},"PeriodicalIF":2.6000,"publicationDate":"2024-08-06","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Enhanced Particle Dispersion in Aluminum Melts Using Multi-source Ultrasonic Vibration: Simulation and Experiments\",\"authors\":\"Yeliang Zhu, Xiaogang Fang, Shulin Lv, Shusen Wu, Shifeng Luo, Siliang Yan, Jiguang Liu, Youwen Yang, Yiqing Chen\",\"doi\":\"10.1007/s40962-024-01419-0\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<p>Due to severe acoustic attenuation, the effectiveness of single-source ultrasonic vibration (SUV) in dispersing reinforcement particles within Al matrix composites is limited, particularly when dealing with high weight fractions. In this study, a short-spacing multi-source ultrasonic vibration (MUV) technique, specifically quad-source ultrasonic vibration (QUV), was introduced to prepare SiC<sub>p</sub>/A356 composites with a high weight fraction of 15wt.% SiC particles. The characteristic of acoustic streaming and the dispersion of particles were systematically investigated through numerical simulations and physical experiments. The results reveal that QUV mitigates acoustic attenuation and expands the potential cavitation region (exceeding the cavitation threshold of 1.1 MPa) compared to single-source ultrasonic vibration (SUV). The synergistic effect of multiple ultrasonic waves not only elevates cavitation intensity but also enriches the structures of acoustic streaming, significantly reducing agglomeration and improving the dispersion of SiC particles within the Al matrix. Without ultrasonic treatment, only a small proportion of SiC particles are embedded in the Al matrix, with an S<sub>SiC</sub>/S<sub>t</sub> ratio of merely 2.23%. However, as the number of ultrasonic sources increases, the agglomeration of SiC particles was relieved, and the resultant holes diminish. Remarkably, under QUV treatment, the holes in the composites virtually disappear, and the S<sub>SiC</sub>/S<sub>t</sub> ratio increases to 9.82%. Additionally, the composites exhibit superior mechanical properties, with a tensile strength of 200 MPa and an elongation of 7.0%, which are 10.5% and 38.5% higher than those achieved using SUV, respectively.</p>\",\"PeriodicalId\":14231,\"journal\":{\"name\":\"International Journal of Metalcasting\",\"volume\":\"95 1\",\"pages\":\"\"},\"PeriodicalIF\":2.6000,\"publicationDate\":\"2024-08-06\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"International Journal of Metalcasting\",\"FirstCategoryId\":\"88\",\"ListUrlMain\":\"https://doi.org/10.1007/s40962-024-01419-0\",\"RegionNum\":3,\"RegionCategory\":\"材料科学\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q2\",\"JCRName\":\"METALLURGY & METALLURGICAL ENGINEERING\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"International Journal of Metalcasting","FirstCategoryId":"88","ListUrlMain":"https://doi.org/10.1007/s40962-024-01419-0","RegionNum":3,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q2","JCRName":"METALLURGY & METALLURGICAL ENGINEERING","Score":null,"Total":0}
引用次数: 0

摘要

由于声衰减严重,单源超声振动(SUV)在铝基复合材料中分散增强粒子的效果有限,尤其是在处理高重量分数时。在本研究中,引入了一种短间距多源超声振动(MUV)技术,特别是四源超声振动(QUV),用于制备 SiCp/A356 复合材料,其中 SiC 颗粒的重量分数高达 15wt.%。通过数值模拟和物理实验系统地研究了声流特性和颗粒的分散性。结果表明,与单源超声振动(SUV)相比,QUV 可减轻声衰减并扩大潜在空化区域(超过 1.1 MPa 的空化阈值)。多个超声波的协同效应不仅提高了空化强度,还丰富了声流结构,显著减少了团聚,改善了碳化硅颗粒在铝基体中的分散。在未进行超声波处理的情况下,只有一小部分 SiC 颗粒嵌入铝基体中,SSiC/St 比率仅为 2.23%。然而,随着超声源数量的增加,SiC 颗粒的聚集现象得到缓解,由此产生的孔洞也随之减少。值得注意的是,在 QUV 处理过程中,复合材料中的孔洞几乎消失,SSiC/St 比率增加到 9.82%。此外,复合材料还具有优异的机械性能,抗拉强度达到 200 兆帕,伸长率为 7.0%,分别比使用 SUV 时提高了 10.5%和 38.5%。
本文章由计算机程序翻译,如有差异,请以英文原文为准。

摘要图片

查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
Enhanced Particle Dispersion in Aluminum Melts Using Multi-source Ultrasonic Vibration: Simulation and Experiments

Due to severe acoustic attenuation, the effectiveness of single-source ultrasonic vibration (SUV) in dispersing reinforcement particles within Al matrix composites is limited, particularly when dealing with high weight fractions. In this study, a short-spacing multi-source ultrasonic vibration (MUV) technique, specifically quad-source ultrasonic vibration (QUV), was introduced to prepare SiCp/A356 composites with a high weight fraction of 15wt.% SiC particles. The characteristic of acoustic streaming and the dispersion of particles were systematically investigated through numerical simulations and physical experiments. The results reveal that QUV mitigates acoustic attenuation and expands the potential cavitation region (exceeding the cavitation threshold of 1.1 MPa) compared to single-source ultrasonic vibration (SUV). The synergistic effect of multiple ultrasonic waves not only elevates cavitation intensity but also enriches the structures of acoustic streaming, significantly reducing agglomeration and improving the dispersion of SiC particles within the Al matrix. Without ultrasonic treatment, only a small proportion of SiC particles are embedded in the Al matrix, with an SSiC/St ratio of merely 2.23%. However, as the number of ultrasonic sources increases, the agglomeration of SiC particles was relieved, and the resultant holes diminish. Remarkably, under QUV treatment, the holes in the composites virtually disappear, and the SSiC/St ratio increases to 9.82%. Additionally, the composites exhibit superior mechanical properties, with a tensile strength of 200 MPa and an elongation of 7.0%, which are 10.5% and 38.5% higher than those achieved using SUV, respectively.

求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
International Journal of Metalcasting
International Journal of Metalcasting 工程技术-冶金工程
CiteScore
4.20
自引率
42.30%
发文量
174
审稿时长
>12 weeks
期刊介绍: The International Journal of Metalcasting is dedicated to leading the transfer of research and technology for the global metalcasting industry. The quarterly publication keeps the latest developments in metalcasting research and technology in front of the scientific leaders in our global industry throughout the year. All papers published in the the journal are approved after a rigorous peer review process. The editorial peer review board represents three international metalcasting groups: academia (metalcasting professors), science and research (personnel from national labs, research and scientific institutions), and industry (leading technical personnel from metalcasting facilities).
期刊最新文献
Effect of Austenitization Time on Corrosion and Wear Resistance in Austempered Ductile Iron From the Editor Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy The Effect of N Content on the Microstructure and Wear Resistance of Improved High-Carbon Chromium Bearing Steel Enhanced Classification of Refractory Coatings in Foundries: A VPCA-Based Machine Learning Approach
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1