电流对激光粉末床熔化生产的铜-铁-磷不溶性合金摩擦学行为的影响

IF 5.3 1区 工程技术 Q1 ENGINEERING, MECHANICAL Wear Pub Date : 2024-10-10 DOI:10.1016/j.wear.2024.205591
Delong Zeng , Yating Qiu , Yanliang Yi , Daxiang Sun , Changliang Shi , Yang Lu , Shengfeng Zhou
{"title":"电流对激光粉末床熔化生产的铜-铁-磷不溶性合金摩擦学行为的影响","authors":"Delong Zeng ,&nbsp;Yating Qiu ,&nbsp;Yanliang Yi ,&nbsp;Daxiang Sun ,&nbsp;Changliang Shi ,&nbsp;Yang Lu ,&nbsp;Shengfeng Zhou","doi":"10.1016/j.wear.2024.205591","DOIUrl":null,"url":null,"abstract":"<div><div>Cu-based immiscible alloys have significant potential application value in the field of electrical contacts. This study investigated the tribological behavior of Cu-Fe-P immiscible alloys produced via laser powder bed fusion (LPBF) under current-carrying conditions. The alloys consist of softer ε-Cu phase and harder Fe-rich phases. The Fe-rich phase acts as a protective reinforcement during current-carrying friction and wear tests, improving the wear resistance of the alloy. With the increasing current, the coefficient of friction initially rose and then decreased, whereas the wear rate showed a gradual increase. At low currents (0, 2, 3 and 5 A), mechanical wear predominantly governs the wear mechanism. As the current increases, the mechanical wear gradually transitions from adhesive wear to abrasive wear, accompanied by weak oxidative wear. At higher currents (7 A and 10 A), the wear mechanism is dominated by arc erosion wear and oxidative wear. Notably, when the current exceeded 2 A, an oxide film consisting of CuO, Fe<sub>2</sub>O<sub>3</sub>, and Fe<sub>3</sub>O<sub>4</sub> formed, enhancing the frictional properties of the alloy. Once the current surpassed 5 A, the arc discharge occurred at high currents, forming molten phases and arc erosion pits on the worn surface of the Cu-Fe-P immiscible alloy.</div></div>","PeriodicalId":23970,"journal":{"name":"Wear","volume":null,"pages":null},"PeriodicalIF":5.3000,"publicationDate":"2024-10-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"Effect of current on the tribological behavior of Cu-Fe-P immiscible alloy produced by laser powder bed fusion\",\"authors\":\"Delong Zeng ,&nbsp;Yating Qiu ,&nbsp;Yanliang Yi ,&nbsp;Daxiang Sun ,&nbsp;Changliang Shi ,&nbsp;Yang Lu ,&nbsp;Shengfeng Zhou\",\"doi\":\"10.1016/j.wear.2024.205591\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"<div><div>Cu-based immiscible alloys have significant potential application value in the field of electrical contacts. This study investigated the tribological behavior of Cu-Fe-P immiscible alloys produced via laser powder bed fusion (LPBF) under current-carrying conditions. The alloys consist of softer ε-Cu phase and harder Fe-rich phases. The Fe-rich phase acts as a protective reinforcement during current-carrying friction and wear tests, improving the wear resistance of the alloy. With the increasing current, the coefficient of friction initially rose and then decreased, whereas the wear rate showed a gradual increase. At low currents (0, 2, 3 and 5 A), mechanical wear predominantly governs the wear mechanism. As the current increases, the mechanical wear gradually transitions from adhesive wear to abrasive wear, accompanied by weak oxidative wear. At higher currents (7 A and 10 A), the wear mechanism is dominated by arc erosion wear and oxidative wear. Notably, when the current exceeded 2 A, an oxide film consisting of CuO, Fe<sub>2</sub>O<sub>3</sub>, and Fe<sub>3</sub>O<sub>4</sub> formed, enhancing the frictional properties of the alloy. Once the current surpassed 5 A, the arc discharge occurred at high currents, forming molten phases and arc erosion pits on the worn surface of the Cu-Fe-P immiscible alloy.</div></div>\",\"PeriodicalId\":23970,\"journal\":{\"name\":\"Wear\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":5.3000,\"publicationDate\":\"2024-10-10\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Wear\",\"FirstCategoryId\":\"5\",\"ListUrlMain\":\"https://www.sciencedirect.com/science/article/pii/S0043164824003569\",\"RegionNum\":1,\"RegionCategory\":\"工程技术\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q1\",\"JCRName\":\"ENGINEERING, MECHANICAL\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Wear","FirstCategoryId":"5","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S0043164824003569","RegionNum":1,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q1","JCRName":"ENGINEERING, MECHANICAL","Score":null,"Total":0}
引用次数: 0

摘要

铜基不相溶合金在电接触领域具有重要的潜在应用价值。本研究调查了在载流条件下通过激光粉末床熔融(LPBF)生产的铜-铁-磷不溶合金的摩擦学行为。合金由较软的ε-Cu相和较硬的富Fe相组成。在载流摩擦和磨损试验中,富铁相起到了保护性强化作用,提高了合金的耐磨性。随着电流的增加,摩擦系数先上升后下降,而磨损率则逐渐增加。在低电流(0、2、3 和 5 A)条件下,磨损机制主要是机械磨损。随着电流的增加,机械磨损逐渐从粘着磨损过渡到磨料磨损,并伴有微弱的氧化磨损。在更大的电流(7 A 和 10 A)下,磨损机制主要是电弧侵蚀磨损和氧化磨损。值得注意的是,当电流超过 2 A 时,由 CuO、Fe2O3 和 Fe3O4 组成的氧化膜形成,增强了合金的摩擦性能。当电流超过 5 A 时,电弧在高电流下放电,在 Cu-Fe-P 不相溶合金的磨损表面形成熔融相和电弧侵蚀坑。
本文章由计算机程序翻译,如有差异,请以英文原文为准。

摘要图片

查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
Effect of current on the tribological behavior of Cu-Fe-P immiscible alloy produced by laser powder bed fusion
Cu-based immiscible alloys have significant potential application value in the field of electrical contacts. This study investigated the tribological behavior of Cu-Fe-P immiscible alloys produced via laser powder bed fusion (LPBF) under current-carrying conditions. The alloys consist of softer ε-Cu phase and harder Fe-rich phases. The Fe-rich phase acts as a protective reinforcement during current-carrying friction and wear tests, improving the wear resistance of the alloy. With the increasing current, the coefficient of friction initially rose and then decreased, whereas the wear rate showed a gradual increase. At low currents (0, 2, 3 and 5 A), mechanical wear predominantly governs the wear mechanism. As the current increases, the mechanical wear gradually transitions from adhesive wear to abrasive wear, accompanied by weak oxidative wear. At higher currents (7 A and 10 A), the wear mechanism is dominated by arc erosion wear and oxidative wear. Notably, when the current exceeded 2 A, an oxide film consisting of CuO, Fe2O3, and Fe3O4 formed, enhancing the frictional properties of the alloy. Once the current surpassed 5 A, the arc discharge occurred at high currents, forming molten phases and arc erosion pits on the worn surface of the Cu-Fe-P immiscible alloy.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
Wear
Wear 工程技术-材料科学:综合
CiteScore
8.80
自引率
8.00%
发文量
280
审稿时长
47 days
期刊介绍: Wear journal is dedicated to the advancement of basic and applied knowledge concerning the nature of wear of materials. Broadly, topics of interest range from development of fundamental understanding of the mechanisms of wear to innovative solutions to practical engineering problems. Authors of experimental studies are expected to comment on the repeatability of the data, and whenever possible, conduct multiple measurements under similar testing conditions. Further, Wear embraces the highest standards of professional ethics, and the detection of matching content, either in written or graphical form, from other publications by the current authors or by others, may result in rejection.
期刊最新文献
Wear and damage behaviors of wheel-rail with different material matchings under various sand deposition densities of rail top in desert environments Impact of tunneling parameters on disc cutter wear during rock breaking in transient conditions A prediction model of erosion rate under erosion-tension coupling for engine blade Investigation of feed rate impact on microscale surface textures and turning performance of SiAlON ceramic cutting tools Environmental impact evaluation of wear protection materials
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1