CMT焊与MIG焊TC4钛合金接头温度场与应力场对比分析

IF 0.6 4区 工程技术 Q4 MECHANICS Mechanika Pub Date : 2022-12-05 DOI:10.5755/j02.mech.31491
Rui Zhang, X. Gu, Yuxian Meng, Lijuan Zhu
{"title":"CMT焊与MIG焊TC4钛合金接头温度场与应力场对比分析","authors":"Rui Zhang, X. Gu, Yuxian Meng, Lijuan Zhu","doi":"10.5755/j02.mech.31491","DOIUrl":null,"url":null,"abstract":"A model was used for the cold metal transfer (CMT) welding based on the volume heat flux distribution of double ellipsoids loaded with time intervals. The temperature field and stress field of TC4 titanium alloy were numerically simulated by ANSYS software. The distribution laws of temperature, residual stress and post-weld deformation during CMT and MIG welding were studied and compared. It was found that the maximum temperature of the molten pool in CMT welding was fluctuating and rising during the loading process, while the temperature of the molten pool in MIG welding was rising smoothly and the maximum temperature was higher than that in CMT welding. The welding stress field was analyzed by thermal-stress coupling analysis. The stress distribution simulated based on the MIG welding heat source was similar to CMT welding, but the maximum von Mises stress was greater than that of CMT welding. Due to the cooling shrinkage, both of them would produce angular deformation after welding. And the maximum angular deformation simulated based on the MIG welding heat source was greater than that of CMT welding. It was proved by welding simulation that CMT welding could reduce welding heat input and residual stress and deformation after welding.","PeriodicalId":54741,"journal":{"name":"Mechanika","volume":" ","pages":""},"PeriodicalIF":0.6000,"publicationDate":"2022-12-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"1","resultStr":"{\"title\":\"Comparative Analysis of Temperature Field and Stress Field of TC4 Ti-tanium Alloy Joint Between CMT and MIG Welding\",\"authors\":\"Rui Zhang, X. Gu, Yuxian Meng, Lijuan Zhu\",\"doi\":\"10.5755/j02.mech.31491\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"A model was used for the cold metal transfer (CMT) welding based on the volume heat flux distribution of double ellipsoids loaded with time intervals. The temperature field and stress field of TC4 titanium alloy were numerically simulated by ANSYS software. The distribution laws of temperature, residual stress and post-weld deformation during CMT and MIG welding were studied and compared. It was found that the maximum temperature of the molten pool in CMT welding was fluctuating and rising during the loading process, while the temperature of the molten pool in MIG welding was rising smoothly and the maximum temperature was higher than that in CMT welding. The welding stress field was analyzed by thermal-stress coupling analysis. The stress distribution simulated based on the MIG welding heat source was similar to CMT welding, but the maximum von Mises stress was greater than that of CMT welding. Due to the cooling shrinkage, both of them would produce angular deformation after welding. And the maximum angular deformation simulated based on the MIG welding heat source was greater than that of CMT welding. It was proved by welding simulation that CMT welding could reduce welding heat input and residual stress and deformation after welding.\",\"PeriodicalId\":54741,\"journal\":{\"name\":\"Mechanika\",\"volume\":\" \",\"pages\":\"\"},\"PeriodicalIF\":0.6000,\"publicationDate\":\"2022-12-05\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"1\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Mechanika\",\"FirstCategoryId\":\"5\",\"ListUrlMain\":\"https://doi.org/10.5755/j02.mech.31491\",\"RegionNum\":4,\"RegionCategory\":\"工程技术\",\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q4\",\"JCRName\":\"MECHANICS\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Mechanika","FirstCategoryId":"5","ListUrlMain":"https://doi.org/10.5755/j02.mech.31491","RegionNum":4,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q4","JCRName":"MECHANICS","Score":null,"Total":0}
引用次数: 1

摘要

基于双椭球体体积热通量随时间间隔的分布,建立了冷态金属转移焊接模型。利用ANSYS软件对TC4钛合金的温度场和应力场进行了数值模拟。研究并比较了CMT和MIG焊接过程中温度、残余应力和焊后变形的分布规律。研究发现,在加载过程中,CMT焊接熔池的最高温度呈波动上升趋势,而MIG焊接熔池温度平稳上升,最高温度高于CMT焊接。采用热应力耦合分析方法对焊接应力场进行了分析。基于MIG焊接热源模拟的应力分布与CMT焊接相似,但最大von Mises应力大于CMT焊接。由于冷却收缩,两者在焊接后都会产生角变形。基于MIG焊接热源模拟的最大角变形大于CMT焊接。焊接仿真结果表明,CMT焊接可以减少焊接热输入,减少焊后残余应力和变形。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
Comparative Analysis of Temperature Field and Stress Field of TC4 Ti-tanium Alloy Joint Between CMT and MIG Welding
A model was used for the cold metal transfer (CMT) welding based on the volume heat flux distribution of double ellipsoids loaded with time intervals. The temperature field and stress field of TC4 titanium alloy were numerically simulated by ANSYS software. The distribution laws of temperature, residual stress and post-weld deformation during CMT and MIG welding were studied and compared. It was found that the maximum temperature of the molten pool in CMT welding was fluctuating and rising during the loading process, while the temperature of the molten pool in MIG welding was rising smoothly and the maximum temperature was higher than that in CMT welding. The welding stress field was analyzed by thermal-stress coupling analysis. The stress distribution simulated based on the MIG welding heat source was similar to CMT welding, but the maximum von Mises stress was greater than that of CMT welding. Due to the cooling shrinkage, both of them would produce angular deformation after welding. And the maximum angular deformation simulated based on the MIG welding heat source was greater than that of CMT welding. It was proved by welding simulation that CMT welding could reduce welding heat input and residual stress and deformation after welding.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
Mechanika
Mechanika 物理-力学
CiteScore
1.30
自引率
0.00%
发文量
50
审稿时长
3 months
期刊介绍: The journal is publishing scientific papers dealing with the following problems: Mechanics of Solid Bodies; Mechanics of Fluids and Gases; Dynamics of Mechanical Systems; Design and Optimization of Mechanical Systems; Mechanical Technologies.
期刊最新文献
Nonlinear vibration characteristics and bifurcation control of a class of piecewise constrained systems with dynamic clearances Model Updating Based on Bayesian Theory and Improved Objective Function Design and FEM Analysis of Plastic Parts of a Tie-Rod Composite Hydraulic Cylinder Real-Time Energy Consumption Sensing System in SMT Intelligent Workshop Research on Bionic Hierarchical Optimization of Wing Based on PLSR and PSO
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1