Aerodynamics of a three-dimensionally deformed rigid wing

IF 2.6 3区 工程技术 Q2 ENGINEERING, MECHANICAL International Journal of Heat and Fluid Flow Pub Date : 2024-09-18 DOI:10.1016/j.ijheatfluidflow.2024.109577
Wenjuan Xu , Lu Shen , Si Peng, Yu Zhou
{"title":"Aerodynamics of a three-dimensionally deformed rigid wing","authors":"Wenjuan Xu ,&nbsp;Lu Shen ,&nbsp;Si Peng,&nbsp;Yu Zhou","doi":"10.1016/j.ijheatfluidflow.2024.109577","DOIUrl":null,"url":null,"abstract":"<div><p>A flexible wing with a large aspect ratio emerges in many modern engineering applications (e.g. solar planes and super large wind turbine blades) and its interaction with incident flow differs markedly from conventional fluid–structure interactions (FSI), exhibiting frequently a large three-dimensional (3D) deformation. Yet, there is little information on how such deformation may change wing aerodynamics. This work investigates the aerodynamic performance of deformed and cantilever-supported NACA0012 rigid wings with an aspect ratio of 9, using ANSYS Fluent with the SST-κ-ω turbulence model at a chord-length-based Reynolds number <em>Re<sub>c</sub></em> of 1.5 × 10<sup>5</sup>. Numerical simulation is validated experimentally. The wing tip bending displacement is up to 4.14c, and the maximum twisted angle is up to 7°. The angle α of attack varies from 0° to 20° at mid span of the wing. It has been found that the torsional deformation can significantly advance the local flow separation, reattachment, bubble length, and transition from laminar to turbulence, resulting in a drop in the critical angle α<sub>cr</sub> of attack, at which the separation bubble size reaches the maximum. Accordingly, the lift and drag coefficients increase, as well as the bending and pitching-up moments, though the stall is advanced due to a change in local α. The tip vortex is also enhanced, inducing strong downwash postponing the separation bubble on the wing and resulting in redistributed force near the wing tip that increases markedly the local bending moment but decrease the local pitching-up moment. On the other hand, the bending deformation tends to produce an effect opposite to the torsion on the flow structure and causing little change in the lift coefficient, though reducing the induced drag and moments appreciably. With both deformations in place, the torsion overwhelms the bending in general in terms of its impact upon aerodynamics and flow structures, the latter acting to cancel at least partially the effect of the former.</p></div>","PeriodicalId":335,"journal":{"name":"International Journal of Heat and Fluid Flow","volume":"110 ","pages":"Article 109577"},"PeriodicalIF":2.6000,"publicationDate":"2024-09-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":null,"platform":"Semanticscholar","paperid":null,"PeriodicalName":"International Journal of Heat and Fluid Flow","FirstCategoryId":"5","ListUrlMain":"https://www.sciencedirect.com/science/article/pii/S0142727X24003023","RegionNum":3,"RegionCategory":"工程技术","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q2","JCRName":"ENGINEERING, MECHANICAL","Score":null,"Total":0}
引用次数: 0

Abstract

A flexible wing with a large aspect ratio emerges in many modern engineering applications (e.g. solar planes and super large wind turbine blades) and its interaction with incident flow differs markedly from conventional fluid–structure interactions (FSI), exhibiting frequently a large three-dimensional (3D) deformation. Yet, there is little information on how such deformation may change wing aerodynamics. This work investigates the aerodynamic performance of deformed and cantilever-supported NACA0012 rigid wings with an aspect ratio of 9, using ANSYS Fluent with the SST-κ-ω turbulence model at a chord-length-based Reynolds number Rec of 1.5 × 105. Numerical simulation is validated experimentally. The wing tip bending displacement is up to 4.14c, and the maximum twisted angle is up to 7°. The angle α of attack varies from 0° to 20° at mid span of the wing. It has been found that the torsional deformation can significantly advance the local flow separation, reattachment, bubble length, and transition from laminar to turbulence, resulting in a drop in the critical angle αcr of attack, at which the separation bubble size reaches the maximum. Accordingly, the lift and drag coefficients increase, as well as the bending and pitching-up moments, though the stall is advanced due to a change in local α. The tip vortex is also enhanced, inducing strong downwash postponing the separation bubble on the wing and resulting in redistributed force near the wing tip that increases markedly the local bending moment but decrease the local pitching-up moment. On the other hand, the bending deformation tends to produce an effect opposite to the torsion on the flow structure and causing little change in the lift coefficient, though reducing the induced drag and moments appreciably. With both deformations in place, the torsion overwhelms the bending in general in terms of its impact upon aerodynamics and flow structures, the latter acting to cancel at least partially the effect of the former.

查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
三维变形刚翼的空气动力学
在许多现代工程应用(如太阳能飞机和超大型风力涡轮机叶片)中,都会出现具有大长宽比的柔性机翼,它与入射流的相互作用与传统的流固相互作用(FSI)明显不同,经常表现出较大的三维(3D)变形。然而,关于这种变形会如何改变机翼空气动力学特性的信息却很少。本研究使用 ANSYS Fluent 和 SST-κ-ω 湍流模型,在基于弦长的雷诺数 Rec 为 1.5 × 105 的条件下,研究了长宽比为 9 的变形和悬臂支撑 NACA0012 刚性机翼的气动性能。实验验证了数值模拟结果。翼尖弯曲位移最大为 4.14c,最大扭曲角为 7°。翼展中部的攻角 α 从 0° 到 20° 不等。研究发现,扭转变形可显著推进局部气流的分离、重新附着、气泡长度以及从层流到湍流的过渡,从而导致临界攻角 αcr 下降,而在临界攻角 αcr 处,分离气泡的尺寸达到最大。翼尖涡流也增强了,引起强烈的下冲,推迟了分离气泡在机翼上的形成,导致翼尖附近的力重新分布,明显增加了局部弯矩,但减小了局部俯仰力矩。另一方面,弯曲变形往往会对气流结构产生与扭转相反的效果,虽然会显著减少诱导阻力和力矩,但对升力系数的影响不大。在两种变形都存在的情况下,就其对空气动力学和流动结构的影响而言,扭转总体上压倒了弯曲,后者至少部分抵消了前者的影响。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
求助全文
约1分钟内获得全文 去求助
来源期刊
International Journal of Heat and Fluid Flow
International Journal of Heat and Fluid Flow 工程技术-工程:机械
CiteScore
5.00
自引率
7.70%
发文量
131
审稿时长
33 days
期刊介绍: The International Journal of Heat and Fluid Flow welcomes high-quality original contributions on experimental, computational, and physical aspects of convective heat transfer and fluid dynamics relevant to engineering or the environment, including multiphase and microscale flows. Papers reporting the application of these disciplines to design and development, with emphasis on new technological fields, are also welcomed. Some of these new fields include microscale electronic and mechanical systems; medical and biological systems; and thermal and flow control in both the internal and external environment.
期刊最新文献
Pseudo three-dimensional topology optimization of chip heat sinks with various inlet–outlet arrangements Investigation of free and impinging jets using generalized k–ω (GEKO) turbulence model Preparation and characterization of modified steel slag-based composite phase change materials Hydrothermal performance enhancement of heat sink using low flow-drag twisted blade-like fins Thermal-hydrodynamic analysis for internally interrupted-finned tubes: Experimental, numerical and performance study
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1