利用 ASPEN Plus 对生物质蒸汽气化系统中添加 CO2 和 CH4 产生合成气的参数研究

IF 1 Q4 ENGINEERING, CHEMICAL Chemical Product and Process Modeling Pub Date : 2024-07-09 DOI:10.1515/cppm-2023-0100
Bingxin Chen
{"title":"利用 ASPEN Plus 对生物质蒸汽气化系统中添加 CO2 和 CH4 产生合成气的参数研究","authors":"Bingxin Chen","doi":"10.1515/cppm-2023-0100","DOIUrl":null,"url":null,"abstract":"\n Biomass gasification technology is increasingly employed as an environmentally friendly energy source, primarily due to its minimal impact on the environment and its ability to mitigate pollution. This technology excels in producing gas with exceptionally high hydrogen content, making it a valuable source for both fuel and energy carriers. Hydrogen (H2), renowned for its stability and lack of detrimental environmental effects, holds great significance in various applications related to energy utilization and sustainability. In the current work, wood sawdust was utilized as the biomass feedstock for syngas production. The research focused on examining the impact of introducing carbon dioxide (CO2) and methane (CH4) gases into the Gibbs reactors. The steam gasification process was modeled by the ASPEN Plus software, allowing for comprehensive analysis and simulation of the gasification reactions. According to the obtained results, the modeling performed in this study demonstrates good predictive capability when compared to the experimental data. It was shown that when the ratio of CO2 to biomass (C/B) increases, the MFR (mass flow rates) of H2 as well as CH4 decrease, whereas the flow rates of CO2 and carbon monoxide (CO) increase. These findings indicate the influence of the C/B ratio on the distribution of different gases within the gasification process. The reduction in MFR of hydrogen when transitioning from C/B = 0 to C/B = 1 in modes a and b is quantified as 17.51 % and 16.39 %, respectively. These percentages represent the magnitude of the decrease in hydrogen MFR for each specific mode when comparing two carbon dioxide to biomass ratios. When the CH4 to biomass (M/B) ratio increases, the mass flow rates of H2 exhibit a consistent upward trend, while the MFR of CO2 displays a descending form. Specifically, when in the Gibbs reactor, M/B rises from 0 to 1 for modes a and b, the mass flow rates of H2 experience significant increases of 265 % and 243 %, respectively. These findings underscore the direct relationship between the M/B ratio and hydrogen production, highlighting the potential for enhanced hydrogen yields with higher M/B ratios in the studied modes.","PeriodicalId":9935,"journal":{"name":"Chemical Product and Process Modeling","volume":null,"pages":null},"PeriodicalIF":1.0000,"publicationDate":"2024-07-09","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":"0","resultStr":"{\"title\":\"A parametric study on syngas production by adding CO2 and CH4 on steam gasification of biomass system using ASPEN Plus\",\"authors\":\"Bingxin Chen\",\"doi\":\"10.1515/cppm-2023-0100\",\"DOIUrl\":null,\"url\":null,\"abstract\":\"\\n Biomass gasification technology is increasingly employed as an environmentally friendly energy source, primarily due to its minimal impact on the environment and its ability to mitigate pollution. This technology excels in producing gas with exceptionally high hydrogen content, making it a valuable source for both fuel and energy carriers. Hydrogen (H2), renowned for its stability and lack of detrimental environmental effects, holds great significance in various applications related to energy utilization and sustainability. In the current work, wood sawdust was utilized as the biomass feedstock for syngas production. The research focused on examining the impact of introducing carbon dioxide (CO2) and methane (CH4) gases into the Gibbs reactors. The steam gasification process was modeled by the ASPEN Plus software, allowing for comprehensive analysis and simulation of the gasification reactions. According to the obtained results, the modeling performed in this study demonstrates good predictive capability when compared to the experimental data. It was shown that when the ratio of CO2 to biomass (C/B) increases, the MFR (mass flow rates) of H2 as well as CH4 decrease, whereas the flow rates of CO2 and carbon monoxide (CO) increase. These findings indicate the influence of the C/B ratio on the distribution of different gases within the gasification process. The reduction in MFR of hydrogen when transitioning from C/B = 0 to C/B = 1 in modes a and b is quantified as 17.51 % and 16.39 %, respectively. These percentages represent the magnitude of the decrease in hydrogen MFR for each specific mode when comparing two carbon dioxide to biomass ratios. When the CH4 to biomass (M/B) ratio increases, the mass flow rates of H2 exhibit a consistent upward trend, while the MFR of CO2 displays a descending form. Specifically, when in the Gibbs reactor, M/B rises from 0 to 1 for modes a and b, the mass flow rates of H2 experience significant increases of 265 % and 243 %, respectively. These findings underscore the direct relationship between the M/B ratio and hydrogen production, highlighting the potential for enhanced hydrogen yields with higher M/B ratios in the studied modes.\",\"PeriodicalId\":9935,\"journal\":{\"name\":\"Chemical Product and Process Modeling\",\"volume\":null,\"pages\":null},\"PeriodicalIF\":1.0000,\"publicationDate\":\"2024-07-09\",\"publicationTypes\":\"Journal Article\",\"fieldsOfStudy\":null,\"isOpenAccess\":false,\"openAccessPdf\":\"\",\"citationCount\":\"0\",\"resultStr\":null,\"platform\":\"Semanticscholar\",\"paperid\":null,\"PeriodicalName\":\"Chemical Product and Process Modeling\",\"FirstCategoryId\":\"1085\",\"ListUrlMain\":\"https://doi.org/10.1515/cppm-2023-0100\",\"RegionNum\":0,\"RegionCategory\":null,\"ArticlePicture\":[],\"TitleCN\":null,\"AbstractTextCN\":null,\"PMCID\":null,\"EPubDate\":\"\",\"PubModel\":\"\",\"JCR\":\"Q4\",\"JCRName\":\"ENGINEERING, CHEMICAL\",\"Score\":null,\"Total\":0}","platform":"Semanticscholar","paperid":null,"PeriodicalName":"Chemical Product and Process Modeling","FirstCategoryId":"1085","ListUrlMain":"https://doi.org/10.1515/cppm-2023-0100","RegionNum":0,"RegionCategory":null,"ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":null,"EPubDate":"","PubModel":"","JCR":"Q4","JCRName":"ENGINEERING, CHEMICAL","Score":null,"Total":0}
引用次数: 0

摘要

生物质气化技术作为一种环境友好型能源被越来越多地采用,这主要是因为它对环境的影响最小,而且能够减轻污染。这种技术擅长生产氢含量极高的气体,使其成为燃料和能源载体的重要来源。氢气(H2)以其稳定性和对环境无有害影响而闻名,在与能源利用和可持续发展有关的各种应用中具有重要意义。在当前的研究中,木锯屑被用作生产合成气的生物质原料。研究重点是考察在吉布斯反应器中引入二氧化碳(CO2)和甲烷(CH4)气体的影响。ASPEN Plus 软件对蒸汽气化过程进行了建模,对气化反应进行了全面的分析和模拟。根据获得的结果,与实验数据相比,本研究中进行的建模显示出良好的预测能力。结果表明,当二氧化碳与生物质(C/B)的比例增加时,H2 和 CH4 的 MFR(质量流量)降低,而二氧化碳和一氧化碳(CO)的流量增加。这些发现表明了 C/B 比率对气化过程中不同气体分布的影响。在模式 a 和 b 中,当从 C/B = 0 过渡到 C/B = 1 时,氢气的 MFR 分别减少了 17.51 % 和 16.39 %。这些百分比代表了在比较两种二氧化碳与生物质比率时,每种特定模式下氢气 MFR 的下降幅度。当 CH4 与生物质 (M/B) 比率增加时,氢气的质量流量呈持续上升趋势,而二氧化碳的 MFR 则呈下降趋势。具体来说,在吉布斯反应器中,当模式 a 和模式 b 的 M/B 从 0 升至 1 时,H2 的质量流量分别显著增加了 265 % 和 243 %。这些发现强调了 M/B 比率与氢气产量之间的直接关系,突出表明在所研究的模式中,M/B 比率越高,氢气产量越高。
本文章由计算机程序翻译,如有差异,请以英文原文为准。
查看原文
分享 分享
微信好友 朋友圈 QQ好友 复制链接
本刊更多论文
A parametric study on syngas production by adding CO2 and CH4 on steam gasification of biomass system using ASPEN Plus
Biomass gasification technology is increasingly employed as an environmentally friendly energy source, primarily due to its minimal impact on the environment and its ability to mitigate pollution. This technology excels in producing gas with exceptionally high hydrogen content, making it a valuable source for both fuel and energy carriers. Hydrogen (H2), renowned for its stability and lack of detrimental environmental effects, holds great significance in various applications related to energy utilization and sustainability. In the current work, wood sawdust was utilized as the biomass feedstock for syngas production. The research focused on examining the impact of introducing carbon dioxide (CO2) and methane (CH4) gases into the Gibbs reactors. The steam gasification process was modeled by the ASPEN Plus software, allowing for comprehensive analysis and simulation of the gasification reactions. According to the obtained results, the modeling performed in this study demonstrates good predictive capability when compared to the experimental data. It was shown that when the ratio of CO2 to biomass (C/B) increases, the MFR (mass flow rates) of H2 as well as CH4 decrease, whereas the flow rates of CO2 and carbon monoxide (CO) increase. These findings indicate the influence of the C/B ratio on the distribution of different gases within the gasification process. The reduction in MFR of hydrogen when transitioning from C/B = 0 to C/B = 1 in modes a and b is quantified as 17.51 % and 16.39 %, respectively. These percentages represent the magnitude of the decrease in hydrogen MFR for each specific mode when comparing two carbon dioxide to biomass ratios. When the CH4 to biomass (M/B) ratio increases, the mass flow rates of H2 exhibit a consistent upward trend, while the MFR of CO2 displays a descending form. Specifically, when in the Gibbs reactor, M/B rises from 0 to 1 for modes a and b, the mass flow rates of H2 experience significant increases of 265 % and 243 %, respectively. These findings underscore the direct relationship between the M/B ratio and hydrogen production, highlighting the potential for enhanced hydrogen yields with higher M/B ratios in the studied modes.
求助全文
通过发布文献求助,成功后即可免费获取论文全文。 去求助
来源期刊
Chemical Product and Process Modeling
Chemical Product and Process Modeling ENGINEERING, CHEMICAL-
CiteScore
2.10
自引率
11.10%
发文量
27
期刊介绍: Chemical Product and Process Modeling (CPPM) is a quarterly journal that publishes theoretical and applied research on product and process design modeling, simulation and optimization. Thanks to its international editorial board, the journal assembles the best papers from around the world on to cover the gap between product and process. The journal brings together chemical and process engineering researchers, practitioners, and software developers in a new forum for the international modeling and simulation community. Topics: equation oriented and modular simulation optimization technology for process and materials design, new modeling techniques shortcut modeling and design approaches performance of commercial and in-house simulation and optimization tools challenges faced in industrial product and process simulation and optimization computational fluid dynamics environmental process, food and pharmaceutical modeling topics drawn from the substantial areas of overlap between modeling and mathematics applied to chemical products and processes.
期刊最新文献
Layouts and tips for a typical final-year chemical engineering graduation project A parametric study on syngas production by adding CO2 and CH4 on steam gasification of biomass system using ASPEN Plus Temperature optimization model to inhibit zero-order kinetic reactions Numerical investigation of discharge pressure effect on steam ejector performance in renewable refrigeration cycle by considering wet steam model and dry gas model Energy efficiency in cooling systems: integrating machine learning and meta-heuristic algorithms for precise cooling load prediction
×
引用
GB/T 7714-2015
复制
MLA
复制
APA
复制
导出至
BibTeX EndNote RefMan NoteFirst NoteExpress
×
×
提示
您的信息不完整,为了账户安全,请先补充。
现在去补充
×
提示
您因"违规操作"
具体请查看互助需知
我知道了
×
提示
现在去查看 取消
×
提示
确定
0
微信
客服QQ
Book学术公众号 扫码关注我们
反馈
×
意见反馈
请填写您的意见或建议
请填写您的手机或邮箱
已复制链接
已复制链接
快去分享给好友吧!
我知道了
×
扫码分享
扫码分享
Book学术官方微信
Book学术文献互助
Book学术文献互助群
群 号:481959085
Book学术
文献互助 智能选刊 最新文献 互助须知 联系我们:info@booksci.cn
Book学术提供免费学术资源搜索服务,方便国内外学者检索中英文文献。致力于提供最便捷和优质的服务体验。
Copyright © 2023 Book学术 All rights reserved.
ghs 京公网安备 11010802042870号 京ICP备2023020795号-1