Journal of Oral Implantology最新文献

Polycaprolactone has exhibited expediency as a biomaterial for bone regenerative procedures preclinically. The present report of the 2 clinical cases in the posterior maxilla is the first to describe clinical application of a customized 3D-printed polycaprolactone mesh for alveolar ridge augmentation. Two patients needing extensive ridge augmentation procedures for dental implant therapy were selected. Polycaprolactone meshes were virtually designed, 3D printed, and applied in combination with a xenogeneic bone substitute. Cone-beam computerized tomography was taken preoperatively, immediately after the surgery, and 1.5-2 years after the delivery of implant prostheses. The serial cone-beam computerized tomography images were superimposed to measure the augmented height and width at 1-mm increments from the implant platform to 3 mm apically. After 2 years, the mean [maximum, minimum] bone gain was 6.05 [8.64, 2.85] mm vertically and 7.77 [10.03, 6.18] mm horizontally at 1 mm below the implant platform. From immediately postoperative to 2 years, there was 14% reduction of augmented ridged height and 24% reduction of augmented width at 1 mm below the platform. All implants placed in augmented sites were successfully maintained until 2 years. The customized polycaprolactone mesh might be a viable material for ridge augmentation in the atrophic posterior maxilla. This needs to be confirmed through randomized controlled clinical trials in future studies.

The aims of the present study are to measure and compare dental implant deviations with fully guided and pilot drill-guided protocols using dynamic navigation systems in polyurethane models. The pilot drill-guided group was determined to be the study group and included 12 implant applications. In this group, the pilot hole was drilled with navigation guidance, and the procedure was completed freehandedly. In the control group, all drilling and implant placement steps were performed using the navigation system, and a total of 12 implants were placed. The pre- and postoperative images were compared to calculate the magnitude of implant deviation. The quantitative data of the 2 groups were compared using the independent-samples t test and Mann-Whitney U test. The analyses revealed that the length of the procedure differed significantly between the 2 groups (P < .001). The procedure duration was significantly shorter in the study group. The entry deviation values of the 2 groups were not significantly different (P = .079). The analysis revealed the apex deviation to be higher in the study group than in the control group (P = .003). However, the 2-dimensional vertical apex deviation values of the implants were not significantly different between groups (P = .068). Angular deviation was determined to be significantly higher in the study group (P < .001). In the present study, all implants were successfully placed in the models using a dynamic navigation system. The results of this study may be useful for future clinical studies.

This case report of a 45-year-old patient at initial presentation shows an illustration of the limitations of periodontal maintenance therapy and subsequent implant prosthetic therapy. In close consultation with the patient, treatment strategies were adopted to maximize the preservation of prognostically questionable teeth. Eight years later, the patient had a highly atrophied maxilla that could be successfully restored with implants. This was achieved with 2 zygoma implants and 2 anterior conventional implants, which were immediately loaded according to the All-on-4 concept and immediately provided with a definitive prosthetic restoration. The case report demonstrates to the general practitioner that using zygoma implants in such constellations may offer a solution to achieve a fixed, rapid, and financially acceptable prosthetic rehabilitation.

Achieving an accurate fit in a complete arch screw-retained implant prosthesis is paramount, regardless of whether analog or digital impressions are employed. In the context of complete arch implant prostheses, using intraoral scanners has sparked significant debate. However, recent advancements in scanner technology, specialized scan gauges meticulously calibrated for precise recording, and the implementation of appropriate scanning techniques have substantially improved the precision and accuracy of digital records. The Nexus iOS scan gauge system represents a pioneering approach, seamlessly integrating these optimization strategies into a purely digital workflow to fabricate complete arch screw-retained implant prostheses in edentulous patients. This case report elucidates the fabrication process of a complete arch screw-retained implant prosthesis that exhibited remarkable fitting accuracy and streamlined the treatment process to a mere 3 appointments. The patient reported high satisfaction with the efficient timeline, aesthetic appeal, and functional performance of the prosthesis. A distinctive advantage of this technique is the notable reduction in treatment steps compared to traditional procedures.

Finite element analysis assists in the understanding of the biomechanical behavior of implants with different designs and material characteristics. Through this analysis, this study aimed to compare the biomechanical behaviors of different designs and configurations of titanium (tapered or cylindric) and zirconia dental implants in the edentulous anterior maxilla. Three-dimensional models of the edentulous maxilla, dental implants, and prosthetic structures were modeled, and different loading conditions were applied to simulate realistic conditions. A total of 6 different models were evaluated: the model (M1) in which tapered implants were located bilaterally in the central canine, the model (M2) in which tapered implants were located bilaterally in the lateral canine, the model (M3) in which cylindric implants were located bilaterally in the central canine, the model (M4) in which cylindric implants were located bilaterally in the lateral canine, the model (M5) in which zirconia implants were located bilaterally in the central canine, and the model (M6) in which zirconia implants were located bilaterally in the lateral canine. Maximum tensile and compressive stress values were recorded at M4 under vertical loading and at M6 under oblique loading, whereas minimum stress values were recorded at M1 under all loading conditions. Maximum von Mises stress values under vertical and oblique loading conditions were observed at M3 and M4, while the minimum stress was observed at M1 and M2. In conclusion, zirconia implants may present a biomechanically convenient and esthetic alternative treatment option in edentulous anterior maxilla rehabilitation compared with tapered and cylindric implants.

This study evaluated the clinical survival rates of 170 Morse taper implants through clinical and mechanical parameters in different therapeutic approaches such as single crowns, fixed partial prostheses, and fixed full-arch prostheses. Patients referred to the Center on Education and Research on Dental Implants from May 2017 to July 2018 with the indication for dental implant therapy, aged >18 years, without periodontal disease, recent evidence of inflammatory activity or other oral disorders, current pregnancy, uncontrolled diabetes mellitus or heavy smoking habit were included in this study. After 12 weeks of healing since the implants were placed in the mandible and after 16 weeks following implants placed in the maxilla, patients returned to the Center for prosthetic rehabilitation. After implant therapy, all patients underwent periodical, clinical, and prosthetic examinations every 6 months. Prosthetic restorations involved 109 fixed reconstructions in function. Few prosthetic complications were reported (6.55%). Twenty implants were rehabilitated with cemented prostheses; from those, 1 crown suffered a loss in retention/decementation. Of the 148 implants rehabilitated with screwed-retained prostheses, 6.76% suffered prosthetic screw loosening. The cumulative implant survival rate was 98.2%. When peri-implant tissue health was evaluated, the keratinized mucosa band appeared related to peri-implant tissue stability. Thus, Morse taper implants represented a successful procedure for implant rehabilitation, with a high cumulative implant survival rate, low prevalence of biological and prosthetic complications, and good stability of peri-implant tissues over the assessed period.

The study is aimed to assess the effects of serum vitamin D levels and their relationship to early dental implant failures. A total of 174 implants in 109 patients were placed and serum vitamin D levels were noted on the day of implant placement. Implants were followed up until restoration, approximately 3-6 months later, and any implant failure was reported based on 50% or more bone loss or implant mobility. Eight individuals had an implant fail early and their vitamin D levels had a mean of 42.54 ng/mL compared with the successful patients' levels of 31.92 ng/mL. Although not statistically significant, there was no correlation between patients' low serum vitamin D levels and early implant failure.

A series of 50 cases involving reconstruction of the fully edentulous maxilla using sinus grafts, bone expansion, and classic crown and bridge to restore to normal contour, comfort, health, function, and esthetics is retrospectively analyzed using 25 years of follow-up data.

Bone augmentation is often required before the installation of dental implants. Here, we report a case for a patient who previously received bone augmentation at the upper right jaw using a xenogenic graft, followed by successful implant installation. Seven years later, the patient presented with mucosal fenestration with bone exposure at the area and gave a history of a recent diagnosis of cutaneous lichen planus. Several attempts were made to manage the situation, and finally, we resorted to connective tissue graft placement at the site. A piece of bone was sent for histologic evaluation, where the results indicated the presence of un-resorbed graft material surrounded by inflammatory cells, with no evidence of bone formation in the area. The case presents histologic evidence for the lack of new bone formation using xenograft over the evaluation period. The case also shows lichen planus, a possible cause for oral complication for patients undergoing augmentation and implant installation.

The stability of implant-abutment joint is fundamental for the long-term success of implant rehabilitation. The screw loosening, fracture, and head deformation are among the most common mechanical complications. Several surface treatments of titanium screws have been proposed to improve their resistance and stability. Diamond-like carbon (DLC) coating of the materials is widely used to increase their wear resistance and durability. The present study aimed to evaluate the effect of carbon fiber coating on the screw head on screw removal torque and screw head stripping. One hundred titanium implant screws were used, 50 without coating (Group 1) and 50 with DLC coating of the screw head (Group 2). Each screw was tightened with a torque of 25 Ncm and unscrewed 10 times. The removal torque was measured with a digital cap torque tester for each loosening. Optical 3d measurement of the screw head surface was performed by a fully automatic machine before and after multiple tightening to investigate surface modifications. The reverse torque values decreased with repeated tightening and loosening cycles in both groups without significant differences (P > .05). Optical measurements of surface dimensions revealed average changes of 0.0357 mm in Group 1 and 0.02312 mm in Group 2, which resulted to be statistically significant (P < .001). The DLC coating of the retention screw head can prevent its distortion and wear, especially after multiple tightening.