Mark Lohatepanont, Melody Chen, Luis Carlos Mendoza Nova, John-Thomas Murray, Wilson Merchan-Merchan
This study investigates the influence of microstructure patterns on the hydrophobic properties of surfaces of 3D-printed objects generated using photopolymer resin. Various arrangements and designs of microstructures on the surface of 3D-printed objects were examined. Leveraging the superior resolution of stereolithography printers (SLA) over fused deposition modeling, intricate microfeature designs were well-implemented. The experiments involved a range of structures on the surface of the 3D-printed objects, including precisely defined arrays of microcylinders, microchannels, and other complex designs generated by parametric equations. The hydrophobicity of the 3D-printed objects was assessed through the water droplet test, revealing a spectrum of results ranging from hydrophobic to weakly hydrophobic, and to hydrophilic surfaces. Light microscopy was employed to characterize the surface morphological properties of the 3D-printed objects, which were then correlated with the measured contact angles. It was discovered that the 3D-printed objects with microstructures formed using parametric functions exhibited patterns with irregularities and fluctuations along all directions or axes, resulting in a higher degree of hydrophobicity compared to structured matrices with pillared arrays. However, some surfaces created with parametric functions resulted in an anisotropic system where the material properties varied along one direction, while the other direction exhibited a flat, planar surface. These anisotropic systems were found to be less hydrophobic according to the water droplet test.
{"title":"Exploring Microstructure Patterns: Influence on Hydrophobic Properties of 3D-Printed Surfaces","authors":"Mark Lohatepanont, Melody Chen, Luis Carlos Mendoza Nova, John-Thomas Murray, Wilson Merchan-Merchan","doi":"10.3390/micro4030028","DOIUrl":"https://doi.org/10.3390/micro4030028","url":null,"abstract":"This study investigates the influence of microstructure patterns on the hydrophobic properties of surfaces of 3D-printed objects generated using photopolymer resin. Various arrangements and designs of microstructures on the surface of 3D-printed objects were examined. Leveraging the superior resolution of stereolithography printers (SLA) over fused deposition modeling, intricate microfeature designs were well-implemented. The experiments involved a range of structures on the surface of the 3D-printed objects, including precisely defined arrays of microcylinders, microchannels, and other complex designs generated by parametric equations. The hydrophobicity of the 3D-printed objects was assessed through the water droplet test, revealing a spectrum of results ranging from hydrophobic to weakly hydrophobic, and to hydrophilic surfaces. Light microscopy was employed to characterize the surface morphological properties of the 3D-printed objects, which were then correlated with the measured contact angles. It was discovered that the 3D-printed objects with microstructures formed using parametric functions exhibited patterns with irregularities and fluctuations along all directions or axes, resulting in a higher degree of hydrophobicity compared to structured matrices with pillared arrays. However, some surfaces created with parametric functions resulted in an anisotropic system where the material properties varied along one direction, while the other direction exhibited a flat, planar surface. These anisotropic systems were found to be less hydrophobic according to the water droplet test.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"137 46","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-23","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141811110","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Anna Szekeres, Sashka Alexandrova, M. Anastasescu, H. Stroescu, Mariuca Gartner, Péter Petrik
Nanoscale oxides grown in c-silicon, implanted with low-energy (2 keV) H+ ions and fluences ranging from 1013 cm−2 to 1015 cm−2 by RF plasma immersion implantation (PII), have been investigated. The oxidation of the implanted Si layers proceeded in dry O2 at temperatures of 700 °C, 750 °C and 800 °C. The optical characterization of the formed Si/SiOx structures was conducted by electroreflectance (ER) and spectroscopic ellipsometric (SE) measurements. From the ER and SE spectra analysis, the characteristic energy bands of direct electron transitions in Si are elaborated. The stress in dependence on hydrogenation conditions is considered and related to the energy shifts of the Si interband transitions around 3.4 eV. Silicon oxides, grown on PII Si at a low H+ fluence, have a non-stoichiometric nature, as revealed by IR-SE spectra analysis, while with an increasing H+ fluence in the PII Si substrates and/or the subsequent oxidation temperature the stoichiometric Si-O4 units in the oxides become predominant. The development of surface morphology is studied by atomic force microscopy (AFM) imaging. Oxidation of the H+-implanted Si surface region flattens out the surface pits created on the Si surface by H+ implants. Based on the evaluation of the texture index and mean fractal dimension, the isotropic and self-similar character of the studied surfaces is emphasized.
{"title":"Optical and Morphological Characterization of Nanoscale Oxides Grown in Low-Energy H+-Implanted c-Silicon","authors":"Anna Szekeres, Sashka Alexandrova, M. Anastasescu, H. Stroescu, Mariuca Gartner, Péter Petrik","doi":"10.3390/micro4030027","DOIUrl":"https://doi.org/10.3390/micro4030027","url":null,"abstract":"Nanoscale oxides grown in c-silicon, implanted with low-energy (2 keV) H+ ions and fluences ranging from 1013 cm−2 to 1015 cm−2 by RF plasma immersion implantation (PII), have been investigated. The oxidation of the implanted Si layers proceeded in dry O2 at temperatures of 700 °C, 750 °C and 800 °C. The optical characterization of the formed Si/SiOx structures was conducted by electroreflectance (ER) and spectroscopic ellipsometric (SE) measurements. From the ER and SE spectra analysis, the characteristic energy bands of direct electron transitions in Si are elaborated. The stress in dependence on hydrogenation conditions is considered and related to the energy shifts of the Si interband transitions around 3.4 eV. Silicon oxides, grown on PII Si at a low H+ fluence, have a non-stoichiometric nature, as revealed by IR-SE spectra analysis, while with an increasing H+ fluence in the PII Si substrates and/or the subsequent oxidation temperature the stoichiometric Si-O4 units in the oxides become predominant. The development of surface morphology is studied by atomic force microscopy (AFM) imaging. Oxidation of the H+-implanted Si surface region flattens out the surface pits created on the Si surface by H+ implants. Based on the evaluation of the texture index and mean fractal dimension, the isotropic and self-similar character of the studied surfaces is emphasized.","PeriodicalId":18535,"journal":{"name":"Micro","volume":" 4","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141825827","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Giselle Rosetta, Matt D. Gunn, John J. Tomes, Mike Butters, Chris E. Finlayson
We report the fabrication and characterisation of near-IR reflecting films and coatings based on shear-assembled crystalline ensembles of polymer composite microspheres, also known as “polymer opals”. Extension of the emulsion polymerisation techniques for synthesis of tractable larger core-interlayer-shell (CIS) particles, of up to half a micron diameter, facilitates the engineering and processing of thin-film synthetic opals, with a tunable photonic stopband spanning an extended spectral range of λ ≈ 700–1600 nm. Samples exhibit strong “scattering cone” interactions, with considerable angular dependence and angle tuning possible, as measured with a goniometric technique. These intense optical resonances in the near-IR, particularly within the important region around λ ~ 800 nm, combined with an appreciable translucency within the visible light spectrum, is indicative of the potential applications in coatings technologies and solar cells.
{"title":"Extending Polymer Opal Structural Color Properties into the Near-Infrared","authors":"Giselle Rosetta, Matt D. Gunn, John J. Tomes, Mike Butters, Chris E. Finlayson","doi":"10.3390/micro4020024","DOIUrl":"https://doi.org/10.3390/micro4020024","url":null,"abstract":"We report the fabrication and characterisation of near-IR reflecting films and coatings based on shear-assembled crystalline ensembles of polymer composite microspheres, also known as “polymer opals”. Extension of the emulsion polymerisation techniques for synthesis of tractable larger core-interlayer-shell (CIS) particles, of up to half a micron diameter, facilitates the engineering and processing of thin-film synthetic opals, with a tunable photonic stopband spanning an extended spectral range of λ ≈ 700–1600 nm. Samples exhibit strong “scattering cone” interactions, with considerable angular dependence and angle tuning possible, as measured with a goniometric technique. These intense optical resonances in the near-IR, particularly within the important region around λ ~ 800 nm, combined with an appreciable translucency within the visible light spectrum, is indicative of the potential applications in coatings technologies and solar cells.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"28 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141386096","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Jawad Naeem, A. Mazari, Z. Kůs, A. Havelka, Mohamed Abdelkader
The aim of this study is to predict the distribution of temperature at various positions on silver-coated firefighter protective clothing when subjected to external radiant heat flux. This will be helpful in the determination of thermal protective performance. Firefighter clothing consists of three layers, i.e., the outer shell, moisture barrier and thermal liner. The outer shell is the exposed surface, which was coated with silver particles through a physical vapor deposition process called magnetron sputtering. Afterwards, these uncoated and silver-coated samples were exposed to radiant heat transmission equipment at 10 kW/m2 as per the ISO 6942 standard. Silver-coated samples displayed better thermal protective performance as the rate of temperature rise in silver-coated samples slowed. Later, a numerical approach was employed, contemplating the impact of metallic coating on the exterior shell. The finite difference method was utilized for solving partial differential equations and the implicit method was employed to discretize the partial differential equations. The numerical model displayed a good prediction of the distribution of temperature at different nodes with respect to time. The comparison of time vs. temperature graphs at different nodes for uncoated and silver-coated samples acquired from numerical solutions showed similar patterns, as witnessed in the experimental results.
本研究的目的是预测涂银消防员防护服在外部辐射热流作用下不同位置的温度分布。这将有助于确定热防护性能。消防员服装由三层组成，即外壳、防潮层和隔热衬里。外壳是暴露在外的表面，它通过一种称为磁控溅射的物理气相沉积工艺镀上银颗粒。然后，按照 ISO 6942 标准，将这些未涂层和银涂层样品暴露在 10 kW/m2 的辐射传热设备中。银涂层样品的热保护性能更好，因为银涂层样品的温度上升速度减慢。随后，考虑到金属涂层对外壳的影响，采用了数值方法。利用有限差分法求解偏微分方程，利用隐含法离散偏微分方程。数值模型很好地预测了不同节点处温度随时间的分布。通过比较数值解法获得的未涂层和银涂层样品不同节点处的时间与温度曲线图，显示出与实验结果相似的模式。
{"title":"Implementation of Numerical Model for Prediction of Temperature Distribution for Metallic-Coated Firefighter Protective Clothing","authors":"Jawad Naeem, A. Mazari, Z. Kůs, A. Havelka, Mohamed Abdelkader","doi":"10.3390/micro4020023","DOIUrl":"https://doi.org/10.3390/micro4020023","url":null,"abstract":"The aim of this study is to predict the distribution of temperature at various positions on silver-coated firefighter protective clothing when subjected to external radiant heat flux. This will be helpful in the determination of thermal protective performance. Firefighter clothing consists of three layers, i.e., the outer shell, moisture barrier and thermal liner. The outer shell is the exposed surface, which was coated with silver particles through a physical vapor deposition process called magnetron sputtering. Afterwards, these uncoated and silver-coated samples were exposed to radiant heat transmission equipment at 10 kW/m2 as per the ISO 6942 standard. Silver-coated samples displayed better thermal protective performance as the rate of temperature rise in silver-coated samples slowed. Later, a numerical approach was employed, contemplating the impact of metallic coating on the exterior shell. The finite difference method was utilized for solving partial differential equations and the implicit method was employed to discretize the partial differential equations. The numerical model displayed a good prediction of the distribution of temperature at different nodes with respect to time. The comparison of time vs. temperature graphs at different nodes for uncoated and silver-coated samples acquired from numerical solutions showed similar patterns, as witnessed in the experimental results.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"135 46","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-21","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141115143","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Ashutosh Kumar, Cameron Hahn, Stephen Herchen, Alex Soucy, Ethan Carpio, Sophia Harper, Nassim Rahmani, Constantine Anagnostopoulos, Mohammad Faghri
This study presents an innovative lateral flow microfluidic paper-based analytical device (μPAD) designed for conducting quantitative paper-based enzyme-linked immunosorbent assays (p-ELISA), seamlessly executing conventional ELISA steps in a paper-based format. The p-ELISA device utilizes a passive fluidic circuit with functional elements such as a multi-bi-material cantilever (B-MaC) assembly, delay channels, and a buffer zone, all enclosed within housing for autonomous, sequential loading of critical reagents onto the detection zone. This novel approach not only demonstrates a rapid assay completion time of under 30 min, but also boasts reduced reagent requirements, minimal equipment needs, and broad applicability across clinical diagnostics and environmental surveillance. Through detailed descriptions of the design, materials, and fabrication methods for the multi-directional flow assay (MDFA), this manuscript highlights the device’s potential for complex biochemical analyses in a user-friendly and versatile format. Analytical performance evaluation, including a limit of detection (LOD) of 8.4 pM for Rabbit IgG, benchmarks the device’s efficacy compared to existing p-ELISA methodologies. This pioneering work lays the groundwork for future advancements in autonomous diagnostics, aiming to enhance global health outcomes through accessible and reliable testing solutions.
{"title":"A Microfluidic Paper-Based Lateral Flow Device for Quantitative ELISA","authors":"Ashutosh Kumar, Cameron Hahn, Stephen Herchen, Alex Soucy, Ethan Carpio, Sophia Harper, Nassim Rahmani, Constantine Anagnostopoulos, Mohammad Faghri","doi":"10.3390/micro4020022","DOIUrl":"https://doi.org/10.3390/micro4020022","url":null,"abstract":"This study presents an innovative lateral flow microfluidic paper-based analytical device (μPAD) designed for conducting quantitative paper-based enzyme-linked immunosorbent assays (p-ELISA), seamlessly executing conventional ELISA steps in a paper-based format. The p-ELISA device utilizes a passive fluidic circuit with functional elements such as a multi-bi-material cantilever (B-MaC) assembly, delay channels, and a buffer zone, all enclosed within housing for autonomous, sequential loading of critical reagents onto the detection zone. This novel approach not only demonstrates a rapid assay completion time of under 30 min, but also boasts reduced reagent requirements, minimal equipment needs, and broad applicability across clinical diagnostics and environmental surveillance. Through detailed descriptions of the design, materials, and fabrication methods for the multi-directional flow assay (MDFA), this manuscript highlights the device’s potential for complex biochemical analyses in a user-friendly and versatile format. Analytical performance evaluation, including a limit of detection (LOD) of 8.4 pM for Rabbit IgG, benchmarks the device’s efficacy compared to existing p-ELISA methodologies. This pioneering work lays the groundwork for future advancements in autonomous diagnostics, aiming to enhance global health outcomes through accessible and reliable testing solutions.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"49 13","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140969487","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Nathnael S. Abebe, Sunil Pai, Rebecca L. Hwang, P. Broaddus, Yu Miao, Olav Solgaard
Micro-electromechanical systems (MEMS) have the potential to provide low-power phase shifting in silicon photonics, but techniques for designing low-loss devices are necessary for adoption of the technology. Based on coupled mode theory (CMT), we derive analytical expressions relating the loss and, in particular, the phase-dependent loss, to the geometry of the MEMS phase shifters. The analytical model explains the loss mechanisms of MEMS phase shifters and enables simple optimization procedures. Based on that insight, we propose phase shifter geometries that minimize coupling power out of the waveguide. Minimization of the loss is based on mode orthogonality of a waveguide and phase shifter modes. We numerically model such geometries for a silicon nitride MEMS phase shifter over a silicon nitride waveguide, predicting less than −1.08 dB loss over a 2π range and −0.026 dB loss when optimized for a π range. We demonstrate this design framework with a custom silicon nitride process and achieve −0.48 dB insertion loss and less than 0.05 dB transmission variation over a π phase shift. Our work demonstrates the strength of the coupled mode approach for the design and optimization of MEMS phase shifters.
{"title":"Coupled Mode Design of Low-Loss Electromechanical Phase Shifters","authors":"Nathnael S. Abebe, Sunil Pai, Rebecca L. Hwang, P. Broaddus, Yu Miao, Olav Solgaard","doi":"10.3390/micro4020021","DOIUrl":"https://doi.org/10.3390/micro4020021","url":null,"abstract":"Micro-electromechanical systems (MEMS) have the potential to provide low-power phase shifting in silicon photonics, but techniques for designing low-loss devices are necessary for adoption of the technology. Based on coupled mode theory (CMT), we derive analytical expressions relating the loss and, in particular, the phase-dependent loss, to the geometry of the MEMS phase shifters. The analytical model explains the loss mechanisms of MEMS phase shifters and enables simple optimization procedures. Based on that insight, we propose phase shifter geometries that minimize coupling power out of the waveguide. Minimization of the loss is based on mode orthogonality of a waveguide and phase shifter modes. We numerically model such geometries for a silicon nitride MEMS phase shifter over a silicon nitride waveguide, predicting less than −1.08 dB loss over a 2π range and −0.026 dB loss when optimized for a π range. We demonstrate this design framework with a custom silicon nitride process and achieve −0.48 dB insertion loss and less than 0.05 dB transmission variation over a π phase shift. Our work demonstrates the strength of the coupled mode approach for the design and optimization of MEMS phase shifters.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"346 2‐3","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-06","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141006935","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
M. Tsarmpopoulou, Dimitrios Ntemogiannis, A. Stamatelatos, Dimitrios Geralis, V. Karoutsos, M. Sigalas, Panagiotis Poulopoulos, S. Grammatikopoulos
Considering that the plasmonic properties of metallic nanoparticles (NPs) are strongly influenced by their dielectric environment, comprehension and manipulation of this interplay are crucial for the design and optimization of functional plasmonic systems. In this study, the plasmonic behavior of silver nanoparticles encapsulated in diverse copolymer dielectric environments was investigated, focusing on the analysis of the emerging localized surface plasmon resonances (LSPRs) through both experimental and theoretical approaches. Specifically, two series of nanostructured silver ultrathin films were deposited via magnetron sputtering on heated Corning Glass substrates at 330 °C and 420 °C, respectively, resulting in the formation of self-assembled NPs of various sizes and distributions. Subsequently, three different polymeric layers were spin-coated on top of the silver NPs. Optical and structural characterization were carried out by means of UV–Vis spectroscopy and atomic force microscopy, respectively. Rigorous Coupled Wave Analysis (RCWA) was employed to study the LSPRs theoretically. The polymeric environment consistently induced a red shift as well as various alterations in the LSPR amplitude, suggesting the potential tunability of the system.
{"title":"Silver Nanoparticles’ Localized Surface Plasmon Resonances Emerged in Polymeric Environments: Theory and Experiment","authors":"M. Tsarmpopoulou, Dimitrios Ntemogiannis, A. Stamatelatos, Dimitrios Geralis, V. Karoutsos, M. Sigalas, Panagiotis Poulopoulos, S. Grammatikopoulos","doi":"10.3390/micro4020020","DOIUrl":"https://doi.org/10.3390/micro4020020","url":null,"abstract":"Considering that the plasmonic properties of metallic nanoparticles (NPs) are strongly influenced by their dielectric environment, comprehension and manipulation of this interplay are crucial for the design and optimization of functional plasmonic systems. In this study, the plasmonic behavior of silver nanoparticles encapsulated in diverse copolymer dielectric environments was investigated, focusing on the analysis of the emerging localized surface plasmon resonances (LSPRs) through both experimental and theoretical approaches. Specifically, two series of nanostructured silver ultrathin films were deposited via magnetron sputtering on heated Corning Glass substrates at 330 °C and 420 °C, respectively, resulting in the formation of self-assembled NPs of various sizes and distributions. Subsequently, three different polymeric layers were spin-coated on top of the silver NPs. Optical and structural characterization were carried out by means of UV–Vis spectroscopy and atomic force microscopy, respectively. Rigorous Coupled Wave Analysis (RCWA) was employed to study the LSPRs theoretically. The polymeric environment consistently induced a red shift as well as various alterations in the LSPR amplitude, suggesting the potential tunability of the system.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"14 22","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-02","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141020480","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
This study introduces a novel approach for analyzing thin film interference spectra by employing a micro-spectrometer equipped with a spectral chip. Focusing on zinc oxide (ZnO) thin films prepared via the sol–gel method, this research aims to explore the films’ physical properties through spectral analysis. After obtaining the interference spectrum of the ZnO thin films, the peak positions within the spectrum were cataloged. Mathematical simulation was used to adjust the refractive index and thickness of the films to match the simulated interference peak positions with the observed peak positions. The thickness of the prepared ZnO film was estimated to be 4.9 μm and its refractive index at 80 °C was estimated to be 1.96. In addition, the measurement system was used to detect environmental changes, including temperature changes and gas exposure. It was observed that the optical characteristics of ZnO films exhibit marked variations with temperature shifts, enabling the establishment of a temperature calibration curve based on spectral feature displacement. In addition, experiments using a variety of gases showed that NO2 and gaseous isopropanol significantly affect the interference spectrum of ZnO, with the peak of the interference spectrum shifted by 2.3 nm and 5.2 nm, respectively, after injection of the two gases. This indicates that interferometric spectroscopy can serve as an effective tool for ZnO monitoring, capable of selectively detecting specific gases.
{"title":"Micro-Spectrometer-Based Interferometric Spectroscopy and Environmental Sensing with Zinc Oxide Thin Film","authors":"Ciao-Ming Tsai, Yu-Chen Hsu, Chang-Ting Yang, Wei-Yi Kong, Chitsung Hong, Cheng-Hao Ko","doi":"10.3390/micro4020019","DOIUrl":"https://doi.org/10.3390/micro4020019","url":null,"abstract":"This study introduces a novel approach for analyzing thin film interference spectra by employing a micro-spectrometer equipped with a spectral chip. Focusing on zinc oxide (ZnO) thin films prepared via the sol–gel method, this research aims to explore the films’ physical properties through spectral analysis. After obtaining the interference spectrum of the ZnO thin films, the peak positions within the spectrum were cataloged. Mathematical simulation was used to adjust the refractive index and thickness of the films to match the simulated interference peak positions with the observed peak positions. The thickness of the prepared ZnO film was estimated to be 4.9 μm and its refractive index at 80 °C was estimated to be 1.96. In addition, the measurement system was used to detect environmental changes, including temperature changes and gas exposure. It was observed that the optical characteristics of ZnO films exhibit marked variations with temperature shifts, enabling the establishment of a temperature calibration curve based on spectral feature displacement. In addition, experiments using a variety of gases showed that NO2 and gaseous isopropanol significantly affect the interference spectrum of ZnO, with the peak of the interference spectrum shifted by 2.3 nm and 5.2 nm, respectively, after injection of the two gases. This indicates that interferometric spectroscopy can serve as an effective tool for ZnO monitoring, capable of selectively detecting specific gases.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"48 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141025667","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Anitta Jose, Tom Mathew, Nora Fernández-Navas, C. J. Querebillo
The advancement of both porous materials and nanomaterials has brought about porous nanomaterials. These new materials present advantages both due to their porosity and nano-size: small size apt for micro/nano device integration or in vivo transport, large surface area for guest/target molecule adsorption and interaction, porous channels providing accessibility to active/surface sites, and exposed reactive surface/active sites induced by uncoordinated bonds. These properties prove useful for the development of different porous composition types (metal oxides, silica, zeolites, amorphous oxides, nanoarrays, precious metals, non-precious metals, MOFs, carbon nanostructures, MXenes, and others) through different synthetic procedures—templating, colloidal synthesis, hydrothermal approach, sol-gel route, self-assembly, dealloying, galvanostatic replacement, and so—for different applications, such as catalysis (water-splitting, etc.), biosensing, energy storage (batteries, supercapacitors), actuators, SERS, and bio applications. Here, these are presented according to different material types showing the evolution of the structure design and development towards the formation of hierarchical porous structures, emphasizing that the formation of porous nanostructures came about out of the desire and need to form hierarchical porous nanostructures. Common trends observed across these different composition types include similar (aforementioned) applications and the use of porous nanomaterials as templates/precursors to create novel ones. Towards the end, a discussion on the link between technological advancements and the development of porous nanomaterials paves the way to present future perspectives on these nanomaterials and their hierarchical porous architectures. Together with a summary, these are given in the conclusion.
{"title":"Porous Inorganic Nanomaterials: Their Evolution towards Hierarchical Porous Nanostructures","authors":"Anitta Jose, Tom Mathew, Nora Fernández-Navas, C. J. Querebillo","doi":"10.3390/micro4020016","DOIUrl":"https://doi.org/10.3390/micro4020016","url":null,"abstract":"The advancement of both porous materials and nanomaterials has brought about porous nanomaterials. These new materials present advantages both due to their porosity and nano-size: small size apt for micro/nano device integration or in vivo transport, large surface area for guest/target molecule adsorption and interaction, porous channels providing accessibility to active/surface sites, and exposed reactive surface/active sites induced by uncoordinated bonds. These properties prove useful for the development of different porous composition types (metal oxides, silica, zeolites, amorphous oxides, nanoarrays, precious metals, non-precious metals, MOFs, carbon nanostructures, MXenes, and others) through different synthetic procedures—templating, colloidal synthesis, hydrothermal approach, sol-gel route, self-assembly, dealloying, galvanostatic replacement, and so—for different applications, such as catalysis (water-splitting, etc.), biosensing, energy storage (batteries, supercapacitors), actuators, SERS, and bio applications. Here, these are presented according to different material types showing the evolution of the structure design and development towards the formation of hierarchical porous structures, emphasizing that the formation of porous nanostructures came about out of the desire and need to form hierarchical porous nanostructures. Common trends observed across these different composition types include similar (aforementioned) applications and the use of porous nanomaterials as templates/precursors to create novel ones. Towards the end, a discussion on the link between technological advancements and the development of porous nanomaterials paves the way to present future perspectives on these nanomaterials and their hierarchical porous architectures. Together with a summary, these are given in the conclusion.","PeriodicalId":18535,"journal":{"name":"Micro","volume":" 8","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-04-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140690151","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
T. Błachowicz, Ilda Kola, Andrea Ehrmann, Karoline Guenther, Guido Ehrmann
Magnetic micro and nano sensors can be used in a broad variety of applications, e.g., for navigation, automotives, smartphones and also for health monitoring. Based on physical effects such as the well-known magnetic induction, the Hall effect, tunnel magnetoresistance and giant magnetoresistance, they can be used to measure positions, flow, pressure and other physical properties. In biomedicine and healthcare, these miniaturized sensors can be either integrated into garments and other wearables, be directed through the body by passive capsules or active micro-robots or be implanted, which usually necessitates bio-functionalization and avoiding cell-toxic materials. This review describes the physical effects that can be applied in these sensors and discusses the most recent micro and nano sensors developed for healthcare applications.
{"title":"Magnetic Micro and Nano Sensors for Continuous Health Monitoring","authors":"T. Błachowicz, Ilda Kola, Andrea Ehrmann, Karoline Guenther, Guido Ehrmann","doi":"10.3390/micro4020015","DOIUrl":"https://doi.org/10.3390/micro4020015","url":null,"abstract":"Magnetic micro and nano sensors can be used in a broad variety of applications, e.g., for navigation, automotives, smartphones and also for health monitoring. Based on physical effects such as the well-known magnetic induction, the Hall effect, tunnel magnetoresistance and giant magnetoresistance, they can be used to measure positions, flow, pressure and other physical properties. In biomedicine and healthcare, these miniaturized sensors can be either integrated into garments and other wearables, be directed through the body by passive capsules or active micro-robots or be implanted, which usually necessitates bio-functionalization and avoiding cell-toxic materials. This review describes the physical effects that can be applied in these sensors and discusses the most recent micro and nano sensors developed for healthcare applications.","PeriodicalId":18535,"journal":{"name":"Micro","volume":"35 6","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-04-06","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140734390","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：