Pub Date : 2015-12-23DOI: 10.1103/PHYSREVSTAB.18.121004
D. Pellegrini, A. Latina, D. Schulte, S. Bogacz
The LHeC is envisioned as a natural upgrade of the LHC that aims at delivering an electron beam for collisions with the existing hadronic beams. The current baseline design for the electron facility consists of a multipass superconducting energy-recovery linac (ERL) operating in a continuous wave mode. The unprecedently high energy of the multipass ERL combined with a stringent emittance dilution budget poses new challenges for the beam optics. Here, we investigate the performances of a novel arc architecture based on a flexible momentum compaction lattice that mitigates the effects of synchrotron radiation while containing the bunch lengthening. Extensive beam-dynamics investigations have been performed with PLACET2, a recently developed tracking code for recirculating machines. They include the first end-to-end tracking and a simulation of the machine operation with a continuous beam. This paper briefly describes the Conceptual Design Report lattice, with an emphasis on possible and proposed improvements that emerged from the beam-dynamics studies. The detector bypass section has been integrated in the lattice, and its design choices are presented here. The stable operation of the ERL with a current up to similar to 150 mA in the linacs has been validated in the presence of single- and multibunch wakefields, synchrotron radiation, and beam-beam effects.
{"title":"Beam-dynamics driven design of the LHeC energy-recovery linac","authors":"D. Pellegrini, A. Latina, D. Schulte, S. Bogacz","doi":"10.1103/PHYSREVSTAB.18.121004","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.121004","url":null,"abstract":"The LHeC is envisioned as a natural upgrade of the LHC that aims at delivering an electron beam for collisions with the existing hadronic beams. The current baseline design for the electron facility consists of a multipass superconducting energy-recovery linac (ERL) operating in a continuous wave mode. The unprecedently high energy of the multipass ERL combined with a stringent emittance dilution budget poses new challenges for the beam optics. Here, we investigate the performances of a novel arc architecture based on a flexible momentum compaction lattice that mitigates the effects of synchrotron radiation while containing the bunch lengthening. Extensive beam-dynamics investigations have been performed with PLACET2, a recently developed tracking code for recirculating machines. They include the first end-to-end tracking and a simulation of the machine operation with a continuous beam. This paper briefly describes the Conceptual Design Report lattice, with an emphasis on possible and proposed improvements that emerged from the beam-dynamics studies. The detector bypass section has been integrated in the lattice, and its design choices are presented here. The stable operation of the ERL with a current up to similar to 150 mA in the linacs has been validated in the presence of single- and multibunch wakefields, synchrotron radiation, and beam-beam effects.","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"16 1","pages":"121004"},"PeriodicalIF":0.0,"publicationDate":"2015-12-23","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82373285","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-21DOI: 10.1103/PHYSREVSTAB.18.123403
S. Bettoni, M. Pedrozzi, S. Reiche
Several parameters determine the performance of free electron lasers: the slice and the projected emittance, the slice energy spread, and the peak current are the most crucial ones. The peak current is essentially obtained by magnetic compression stages along the machine or occasionally assisted by velocity bunching at low energy. The minimum emittance and the alignment of the slices along the bunch are mainly determined in the low energy part of the accelerator (injector). Variations at the per-mille level of several parameters in this section of the machine strongly influence these quantities with highly nonlinear dynamic. We developed a numerical tool to perform the optimization of the injector. We applied this code to optimize the SwissFEL injector, assuming different gun designs, initial bunch lengths and intrinsic emittances. We obtained an emittance along the bunch of 0.14 mm mrad and around 0.08 mm mrad for the maximum and the minimum SwissFEL charges (200 and 10 pC, respectively). We applied the same tool to a running injector, where we automatized the optimization of the machine.
几个参数决定了自由电子激光器的性能，其中最关键的是片和投影发射度、片能量扩散和峰值电流。峰值电流基本上是通过沿着机器的磁压缩阶段获得的，或者偶尔在低能量下辅以速度聚集。最小发射度和薄片沿束束的排列主要决定于加速器(注入器)的低能部分。在机器的这一部分中，每英里水平上的几个参数的变化强烈地影响着这些具有高度非线性动态的数量。我们开发了一个数值工具来进行喷射器的优化。我们应用这个代码来优化SwissFEL喷射器，假设不同的喷射器设计、初始束长和固有发射。我们获得了最大和最小SwissFEL电荷(分别为200和10 pC)沿束的发射度为0.14 mm mrad和0.08 mm mrad左右。我们将相同的工具应用于运行中的注入器，在那里我们对机器进行了自动化优化。
{"title":"Low emittance injector design for free electron lasers","authors":"S. Bettoni, M. Pedrozzi, S. Reiche","doi":"10.1103/PHYSREVSTAB.18.123403","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.123403","url":null,"abstract":"Several parameters determine the performance of free electron lasers: the slice and the projected emittance, the slice energy spread, and the peak current are the most crucial ones. The peak current is essentially obtained by magnetic compression stages along the machine or occasionally assisted by velocity bunching at low energy. The minimum emittance and the alignment of the slices along the bunch are mainly determined in the low energy part of the accelerator (injector). Variations at the per-mille level of several parameters in this section of the machine strongly influence these quantities with highly nonlinear dynamic. We developed a numerical tool to perform the optimization of the injector. We applied this code to optimize the SwissFEL injector, assuming different gun designs, initial bunch lengths and intrinsic emittances. We obtained an emittance along the bunch of 0.14 mm mrad and around 0.08 mm mrad for the maximum and the minimum SwissFEL charges (200 and 10 pC, respectively). We applied the same tool to a running injector, where we automatized the optimization of the machine.","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"19 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2015-12-21","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"79251713","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-21DOI: 10.1103/PHYSREVSTAB.18.123402
Y. Liu, Peng Zhang, Shih-Hung Chen, L. Ang
A charge sheet model is proposed to study the space charge effect and uniformity of charge separation of an electron pulse train in a drift space. An analytical formula is derived for the charge density limit as a function of gap spacing, injecting energy and pulse separation. To consider the relativistic effects, the theoretical results are verified by numerical solutions up to 80 MeV. This model can be applied to the design of Smith-Purcell radiation, multiple-pulse electron beam for time resolved electron microscopy, and to free electron laser.
{"title":"Maximal charge injection of a uniform separated electron pulse train in a drift space","authors":"Y. Liu, Peng Zhang, Shih-Hung Chen, L. Ang","doi":"10.1103/PHYSREVSTAB.18.123402","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.123402","url":null,"abstract":"A charge sheet model is proposed to study the space charge effect and uniformity of charge separation of an electron pulse train in a drift space. An analytical formula is derived for the charge density limit as a function of gap spacing, injecting energy and pulse separation. To consider the relativistic effects, the theoretical results are verified by numerical solutions up to 80 MeV. This model can be applied to the design of Smith-Purcell radiation, multiple-pulse electron beam for time resolved electron microscopy, and to free electron laser.","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"18 1","pages":"123402"},"PeriodicalIF":0.0,"publicationDate":"2015-12-21","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"74614800","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-16DOI: 10.1103/PHYSREVSTAB.18.123501
D. Kang, T. Bieler, C. Compton
Large grain niobium (Nb) is being investigated for fabricating superconducting radiofrequency cavities as an alternative to the traditional approach using fine grain polycrystalline Nb sheets. Past studies have identified a surface damage layer on fine grain cavities due to deep drawing and demonstrated the necessity for chemical etching on the surface. However, the origin of and depth of the damage layer are not well understood, and similar exploration on large grain cavities is lacking. In this work, electron backscatter diffraction (EBSD) was used to examine the cross sections at the equator and iris of a half cell deep drawn from a large grain Nb ingot slice. The results indicate that the damage (identified by a high density of geometrically necessary dislocations) depends on crystal orientations, is different at the equator and iris, and is present through the full thickness of a half cell in some places. After electron backscatter diffraction, the specimens were heat treated at 800 °C or 1000 °C for two hours, and the same areas were reexamined. A more dramatic decrease in dislocation content was observed at the iris than the equator, where some regions exhibited no change. The specimens were then etched and examined again, tomore » determine if the subsurface region behaved differently than the surface. As a result, little change in the dislocation substructure was observed, suggesting that the large grain microstructure is retained with a normal furnace anneal.« less
{"title":"Effects of processing history on the evolution of surface damage layer and dislocation substructure in large grain niobium cavities","authors":"D. Kang, T. Bieler, C. Compton","doi":"10.1103/PHYSREVSTAB.18.123501","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.123501","url":null,"abstract":"Large grain niobium (Nb) is being investigated for fabricating superconducting radiofrequency cavities as an alternative to the traditional approach using fine grain polycrystalline Nb sheets. Past studies have identified a surface damage layer on fine grain cavities due to deep drawing and demonstrated the necessity for chemical etching on the surface. However, the origin of and depth of the damage layer are not well understood, and similar exploration on large grain cavities is lacking. In this work, electron backscatter diffraction (EBSD) was used to examine the cross sections at the equator and iris of a half cell deep drawn from a large grain Nb ingot slice. The results indicate that the damage (identified by a high density of geometrically necessary dislocations) depends on crystal orientations, is different at the equator and iris, and is present through the full thickness of a half cell in some places. After electron backscatter diffraction, the specimens were heat treated at 800 °C or 1000 °C for two hours, and the same areas were reexamined. A more dramatic decrease in dislocation content was observed at the iris than the equator, where some regions exhibited no change. The specimens were then etched and examined again, tomore » determine if the subsurface region behaved differently than the surface. As a result, little change in the dislocation substructure was observed, suggesting that the large grain microstructure is retained with a normal furnace anneal.« less","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"35 1","pages":"123501"},"PeriodicalIF":0.0,"publicationDate":"2015-12-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"74068856","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-15DOI: 10.1103/PHYSREVSTAB.18.121003
K. Ohmi, F. Zimmermann
The beam-beam limit at hadron colliders manifests itself in the form of degraded luminosity lifetime and/or reduced beam lifetime. In particular, for increasing beam intensity, the nonlinear beam-beam force causes incoherent emittance growth, while the (linear) coupling force between the two colliding beams can result in coherent beam-beam instabilities. These phenomena may be enhanced (or suppressed) by lattice errors, external noise, and other perturbations. We investigate the luminosity degradation caused both by incoherent emittance growth and by coherent beam-beam instability. The resulting beam-beam limit for an ideal machine and the of question how it is affected by some of the aforementioned errors are discussed in theory and simulation.
{"title":"Fundamental beam-beam limit from head-on interaction in the Large Hadron Collider","authors":"K. Ohmi, F. Zimmermann","doi":"10.1103/PHYSREVSTAB.18.121003","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.121003","url":null,"abstract":"The beam-beam limit at hadron colliders manifests itself in the form of degraded luminosity lifetime and/or reduced beam lifetime. In particular, for increasing beam intensity, the nonlinear beam-beam force causes incoherent emittance growth, while the (linear) coupling force between the two colliding beams can result in coherent beam-beam instabilities. These phenomena may be enhanced (or suppressed) by lattice errors, external noise, and other perturbations. We investigate the luminosity degradation caused both by incoherent emittance growth and by coherent beam-beam instability. The resulting beam-beam limit for an ideal machine and the of question how it is affected by some of the aforementioned errors are discussed in theory and simulation.","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"25 1","pages":"121003"},"PeriodicalIF":0.0,"publicationDate":"2015-12-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"79732418","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-11DOI: 10.1103/PHYSREVSTAB.18.120701
N. Ginzburg, E. V. Ilyakov, I. Kulagin, N. Peskov, R. Rozental, A. Sergeev, V. Zaslavsky, I. Zheleznov
{"title":"Synchronization of radiation in an oversized coaxial Ka-band backward wave oscillator using two-dimensional Bragg structure","authors":"N. Ginzburg, E. V. Ilyakov, I. Kulagin, N. Peskov, R. Rozental, A. Sergeev, V. Zaslavsky, I. Zheleznov","doi":"10.1103/PHYSREVSTAB.18.120701","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.120701","url":null,"abstract":"","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"13 1","pages":"120701"},"PeriodicalIF":0.0,"publicationDate":"2015-12-11","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"84173166","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-11DOI: 10.1103/PHYSREVSTAB.18.121301
H. Avetissian, H. H. Matevosyan, G. F. Mkrtchian, Kh. V. Sedrakian
{"title":"Production of high energy-solid density electron bunches and hard γ -quanta and positron fluxes by ultrarelativistic lasers in solid-plasma targets","authors":"H. Avetissian, H. H. Matevosyan, G. F. Mkrtchian, Kh. V. Sedrakian","doi":"10.1103/PHYSREVSTAB.18.121301","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.121301","url":null,"abstract":"","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"34 1","pages":"121301"},"PeriodicalIF":0.0,"publicationDate":"2015-12-11","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"90237371","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-10DOI: 10.1103/PHYSREVSTAB.18.124001
A. Pham, S. Lee, K. Ng
{"title":"Method of phase space beam dilution utilizing bounded chaos generated by rf phase modulation","authors":"A. Pham, S. Lee, K. Ng","doi":"10.1103/PHYSREVSTAB.18.124001","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.124001","url":null,"abstract":"","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"31 2-3 1","pages":"124001"},"PeriodicalIF":0.0,"publicationDate":"2015-12-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"77913769","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-12-08DOI: 10.1103/PHYSREVSTAB.18.124201
M. Fitterer, C. Carli, A. Molodozhentsev, A. Müller
{"title":"Systematic studies on the effect of linear lattice optics for space-charge limited beams","authors":"M. Fitterer, C. Carli, A. Molodozhentsev, A. Müller","doi":"10.1103/PHYSREVSTAB.18.124201","DOIUrl":"https://doi.org/10.1103/PHYSREVSTAB.18.124201","url":null,"abstract":"","PeriodicalId":20072,"journal":{"name":"Physical Review Special Topics-accelerators and Beams","volume":"75 1","pages":"124201"},"PeriodicalIF":0.0,"publicationDate":"2015-12-08","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"79611243","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：