Mária Petková, V. Jančovičová, A. Ujhelyiová, M. Hricová
This work aims to present the results of evaluating the coloristic properties of polylactic acid (PLA) fibers. PLA is common nowadays in much research, as it is a biodegradable plastic from renewable sources. However, little research is devoted to PLA fibers, and even less to applied research of colored fibers. The prepared color masterbatches, created using inorganic pigments, such as titanium dioxide and carbon black, were subsequently used to prepare dyed PLA fibers in mass. The fibers were drawn to the maximum drawn ratio. The properties of the pure and dyed fibers were investigated before and after accelerated light aging using Q-SUN equipment. The changes were recorded by Fourier Transform Infrared (FTIR) spectroscopy and colorimetric properties were recorded using a device spectrometer from TECHKON SpectroDens. We also evaluated thermal properties from the first heating via differential scanning calorimetry (DSC). The measurements were taken before and after the aging of the PLA fibers, in order to see the effect of aging on the supermolecular structure, excluding the influence of the preparation process and the influence of the kind of PLA. Using inorganic pigments showed sufficient color stability even after accelerated light aging, which is beneficial for using colored fibers in practice.
{"title":"The Coloristic Properties of Biodegradable Fibers","authors":"Mária Petková, V. Jančovičová, A. Ujhelyiová, M. Hricová","doi":"10.3390/fib12070059","DOIUrl":"https://doi.org/10.3390/fib12070059","url":null,"abstract":"This work aims to present the results of evaluating the coloristic properties of polylactic acid (PLA) fibers. PLA is common nowadays in much research, as it is a biodegradable plastic from renewable sources. However, little research is devoted to PLA fibers, and even less to applied research of colored fibers. The prepared color masterbatches, created using inorganic pigments, such as titanium dioxide and carbon black, were subsequently used to prepare dyed PLA fibers in mass. The fibers were drawn to the maximum drawn ratio. The properties of the pure and dyed fibers were investigated before and after accelerated light aging using Q-SUN equipment. The changes were recorded by Fourier Transform Infrared (FTIR) spectroscopy and colorimetric properties were recorded using a device spectrometer from TECHKON SpectroDens. We also evaluated thermal properties from the first heating via differential scanning calorimetry (DSC). The measurements were taken before and after the aging of the PLA fibers, in order to see the effect of aging on the supermolecular structure, excluding the influence of the preparation process and the influence of the kind of PLA. Using inorganic pigments showed sufficient color stability even after accelerated light aging, which is beneficial for using colored fibers in practice.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"56 43","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141644722","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
John Sunny, Jorge Palacios Moreno, Hadi Nazaripoor, Pierre Mertiny
Fibers as a reinforcement in polymer-based composite materials play an essential role in the composites’ mechanical performance. It is, therefore, crucial to understand how fibers are affected by different environmental conditions, such as water exposure at elevated temperatures. Even when embedded in a matrix material, i.e., a thermoset or thermosetting polymer, exposure to moisture may occur. Therefore, in many structural applications of fiber-reinforced polymer composites, moisture may have a significant impact on the reinforcing elements and the rate of degradation. The present work focuses on the effects of hydrothermal aging on the mechanical durability of long carbon and basalt fibers by immersion in tap water at 60 °C, 71 °C, and 82 °C. A service life prediction model based on the Arrhenius technique was explored. Using this model, it is possible to forecast the amount of time that it takes to attain a given degradation level over a specified range of temperatures. The present study also investigated changes in tensile strength in response to exposure to 90% humidity at 90 °C. In addition, the chemical elements released during aging in water were determined. Fourier-transform infrared spectroscopy and mass dissolution studies were conducted to elucidate the mechanism causing strength losses. Scanning electron microscopy was employed to evaluate changes of the fiber surface morphologies due to hydrothermal exposure.
{"title":"Hydrothermal Aging and Humidity Exposure of Carbon and Basalt Fibers and Life Time Prediction","authors":"John Sunny, Jorge Palacios Moreno, Hadi Nazaripoor, Pierre Mertiny","doi":"10.3390/fib12070058","DOIUrl":"https://doi.org/10.3390/fib12070058","url":null,"abstract":"Fibers as a reinforcement in polymer-based composite materials play an essential role in the composites’ mechanical performance. It is, therefore, crucial to understand how fibers are affected by different environmental conditions, such as water exposure at elevated temperatures. Even when embedded in a matrix material, i.e., a thermoset or thermosetting polymer, exposure to moisture may occur. Therefore, in many structural applications of fiber-reinforced polymer composites, moisture may have a significant impact on the reinforcing elements and the rate of degradation. The present work focuses on the effects of hydrothermal aging on the mechanical durability of long carbon and basalt fibers by immersion in tap water at 60 °C, 71 °C, and 82 °C. A service life prediction model based on the Arrhenius technique was explored. Using this model, it is possible to forecast the amount of time that it takes to attain a given degradation level over a specified range of temperatures. The present study also investigated changes in tensile strength in response to exposure to 90% humidity at 90 °C. In addition, the chemical elements released during aging in water were determined. Fourier-transform infrared spectroscopy and mass dissolution studies were conducted to elucidate the mechanism causing strength losses. Scanning electron microscopy was employed to evaluate changes of the fiber surface morphologies due to hydrothermal exposure.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"60 22","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141654397","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcases a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composites for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the applicability of mycelium-based materials has extended beyond their original domains of biology and mycology to architecture.
{"title":"Natural Fiber-Reinforced Mycelium Composite for Innovative and Sustainable Construction Materials","authors":"M. E. Voutetaki, Anastasios C. Mpalaskas","doi":"10.3390/fib12070057","DOIUrl":"https://doi.org/10.3390/fib12070057","url":null,"abstract":"Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcases a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composites for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the applicability of mycelium-based materials has extended beyond their original domains of biology and mycology to architecture.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"92 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-09","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141663998","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pierre-Yves Bloch, Jean-Francis Bloch, Konrad Olejnik, Daniel Brissaud
In this article, we delve into the influence of fiber orientation (structural anisotropy) on paper imbibition, with a particular focus on in-plane imbibition. Utilizing the XLPA experimental method, we analyze several papers with different anisotropies, employing a constant volume of ethanol as the imbibing fluid. Our findings contribute novel insights into the anisotropic behavior of imbibition, a topic not extensively covered in the literature. We analyze how the orientation of fibers significantly influences lateral imbibition, providing a deeper understanding of the microfluidic properties of paper. The anisotropies found for imbibition fit perfectly with the existing data found in the literature, indicating the influence of fiber orientation. Furthermore, the kinetics are shown to be linked directly with the porosity.
{"title":"Anisotropy and Fiber Orientation: A Key Player in the Lateral Imbibition of Cellulose Paper","authors":"Pierre-Yves Bloch, Jean-Francis Bloch, Konrad Olejnik, Daniel Brissaud","doi":"10.3390/fib12070056","DOIUrl":"https://doi.org/10.3390/fib12070056","url":null,"abstract":"In this article, we delve into the influence of fiber orientation (structural anisotropy) on paper imbibition, with a particular focus on in-plane imbibition. Utilizing the XLPA experimental method, we analyze several papers with different anisotropies, employing a constant volume of ethanol as the imbibing fluid. Our findings contribute novel insights into the anisotropic behavior of imbibition, a topic not extensively covered in the literature. We analyze how the orientation of fibers significantly influences lateral imbibition, providing a deeper understanding of the microfluidic properties of paper. The anisotropies found for imbibition fit perfectly with the existing data found in the literature, indicating the influence of fiber orientation. Furthermore, the kinetics are shown to be linked directly with the porosity.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":" 26","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141680708","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Saleemi, H. A. Mannan, Tabinda Riaz, Abdul Moqeet Hai, Hassan Zeb, Amber Khalil Khan
This study reports process optimization studies of silica and zinc oxide-based flame-retardant (FR) coatings on cotton fabric for protective clothing and enhanced flammability properties. The experiments were designed by central composite design (CCD) using response surface methodology (RSM) to assess the synergistic protective effects of silica and zinc oxide FR coating. These prepared sols were coated on cotton fabrics by a simple dip dry cure process. The resulting FR-finished fabrics were characterized by SEM, mechanical properties, flame retardancy, and air permeability. SEM results confirmed the homogenous spreading of particles on cotton fabrics. From TGA results, it was noticed that the incorporation of silica and ZnO in the prepared nano-sols results in improved thermal stability of the FR-finished fabrics. These sol–gel-treated FR cotton fabrics showed excellent comfort properties, which shows their suitability for fire-retardant protective clothing. RSM analysis proved that the predicted values are in good agreement with the experimental values since R2 values for time to ignite, flame spread time, and air permeability were greater than 0.90. The optimized concentration of silica and ZnO in FR-finished fabrics was found to be 0.302% and 0.353%, respectively, which was further confirmed by confirmatory experiments. The optimization analysis successfully optimized the process for synergistic coating of silica and zinc oxide nanoparticles for enhanced flammability properties of FR cotton fabric for protective clothing.
{"title":"Optimizing Synergistic Silica–Zinc Oxide Coating for Enhanced Flammability Resistance in Cotton Protective Clothing","authors":"S. Saleemi, H. A. Mannan, Tabinda Riaz, Abdul Moqeet Hai, Hassan Zeb, Amber Khalil Khan","doi":"10.3390/fib12050044","DOIUrl":"https://doi.org/10.3390/fib12050044","url":null,"abstract":"This study reports process optimization studies of silica and zinc oxide-based flame-retardant (FR) coatings on cotton fabric for protective clothing and enhanced flammability properties. The experiments were designed by central composite design (CCD) using response surface methodology (RSM) to assess the synergistic protective effects of silica and zinc oxide FR coating. These prepared sols were coated on cotton fabrics by a simple dip dry cure process. The resulting FR-finished fabrics were characterized by SEM, mechanical properties, flame retardancy, and air permeability. SEM results confirmed the homogenous spreading of particles on cotton fabrics. From TGA results, it was noticed that the incorporation of silica and ZnO in the prepared nano-sols results in improved thermal stability of the FR-finished fabrics. These sol–gel-treated FR cotton fabrics showed excellent comfort properties, which shows their suitability for fire-retardant protective clothing. RSM analysis proved that the predicted values are in good agreement with the experimental values since R2 values for time to ignite, flame spread time, and air permeability were greater than 0.90. The optimized concentration of silica and ZnO in FR-finished fabrics was found to be 0.302% and 0.353%, respectively, which was further confirmed by confirmatory experiments. The optimization analysis successfully optimized the process for synergistic coating of silica and zinc oxide nanoparticles for enhanced flammability properties of FR cotton fabric for protective clothing.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"47 49","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-17","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140965863","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
In this study, the hyperbaric (2 bar) laser chemical vapor deposition of TiC fibers grown under various percent pressures of hydrogen and ratios of ethylene and titanium tetrachloride (2:1 or 1:1) are reported. In the hydrogen-rich (85%) condition, sequential fiber depositions became stunted as a result of a loss of hydrogen, which served as a reducing agent for the metal halide as hydrogen evolved with the hydrocarbon gas in the reaction zone because of the Le Chatelier principle. For the hydrogen-lean (25%) condition, the intrinsic fiber growth rate was invariant, but gas phase nucleation resulted in the hydrocarbon forming carbon soot in the chamber which subsequently deposited and coated on the fibers. In the hydrogen-balanced composition (50%), the 2:1 precursor ratio resulted in inconsistent intrinsic growth rates which ranged from approximately 30 μm/s to 44 μm/s. However, for the hydrogen-balanced (50%) 1:1 condition, the intrinsic growth rate variation was reduced to approximately 12 μm/s. The differences in fiber uniformity, composition, and structure under these process conditions are discussed in terms of hydrogen’s ability to serve as a reducing agent, a fluid to transport heat from the deposition zone, and alter the structure of the fiber through thermophoresis.
{"title":"Influence of Precursor Mixtures on the Laser Chemical Vapor Deposition of TiC Fibers","authors":"Kendall J. Mitchell, G. B. Thompson","doi":"10.3390/fib12050043","DOIUrl":"https://doi.org/10.3390/fib12050043","url":null,"abstract":"In this study, the hyperbaric (2 bar) laser chemical vapor deposition of TiC fibers grown under various percent pressures of hydrogen and ratios of ethylene and titanium tetrachloride (2:1 or 1:1) are reported. In the hydrogen-rich (85%) condition, sequential fiber depositions became stunted as a result of a loss of hydrogen, which served as a reducing agent for the metal halide as hydrogen evolved with the hydrocarbon gas in the reaction zone because of the Le Chatelier principle. For the hydrogen-lean (25%) condition, the intrinsic fiber growth rate was invariant, but gas phase nucleation resulted in the hydrocarbon forming carbon soot in the chamber which subsequently deposited and coated on the fibers. In the hydrogen-balanced composition (50%), the 2:1 precursor ratio resulted in inconsistent intrinsic growth rates which ranged from approximately 30 μm/s to 44 μm/s. However, for the hydrogen-balanced (50%) 1:1 condition, the intrinsic growth rate variation was reduced to approximately 12 μm/s. The differences in fiber uniformity, composition, and structure under these process conditions are discussed in terms of hydrogen’s ability to serve as a reducing agent, a fluid to transport heat from the deposition zone, and alter the structure of the fiber through thermophoresis.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"71 6","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140983266","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Sebastian Candrea, A. Muntean, Anida-Maria Băbțan, Antonia Boca, C. Feurdean, I. R. Bordea, A. B. Boșca, A. Ilea
Pulpal pathology in young permanent teeth, caused by dental caries or trauma, can lead to disruption of root formation, leaving the tooth with an uncertain prognosis. Current therapies for such cases present a number of limitations; thus, the aim of this article is to provide an overview on the use of nanofibers in endodontics. The search was conducted on two databases and eight articles met the inclusion criteria for this systematic review. Data on nanofiber production and fiber characteristics were extracted and systematized in tables. Moreover, the ability of novel scaffolds to deliver either drugs or different therapeutic agents without interfering with the products’ characteristics is analyzed from the in vitro and in vivo data. The potential for nanofiber-based scaffolds to induce cellular differentiation and overcome the limitations of classic regenerative endodontic treatment is also discussed.
{"title":"The Use of Nanofibers in Regenerative Endodontic Therapy—A Systematic Review","authors":"Sebastian Candrea, A. Muntean, Anida-Maria Băbțan, Antonia Boca, C. Feurdean, I. R. Bordea, A. B. Boșca, A. Ilea","doi":"10.3390/fib12050042","DOIUrl":"https://doi.org/10.3390/fib12050042","url":null,"abstract":"Pulpal pathology in young permanent teeth, caused by dental caries or trauma, can lead to disruption of root formation, leaving the tooth with an uncertain prognosis. Current therapies for such cases present a number of limitations; thus, the aim of this article is to provide an overview on the use of nanofibers in endodontics. The search was conducted on two databases and eight articles met the inclusion criteria for this systematic review. Data on nanofiber production and fiber characteristics were extracted and systematized in tables. Moreover, the ability of novel scaffolds to deliver either drugs or different therapeutic agents without interfering with the products’ characteristics is analyzed from the in vitro and in vivo data. The potential for nanofiber-based scaffolds to induce cellular differentiation and overcome the limitations of classic regenerative endodontic treatment is also discussed.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"55 18","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140983560","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
J. Ortega, Felix Krooß, Yuwei Stefan Li, Thomas Gries
With the megatrend of digitalization, the demand for sensors in previously difficult-to-access scenarios is increasing. Filament-shaped sensors (FSS) are ideal for this demand, especially in applications in which the monitoring of textile structures is the focus. Electrically conductive bicomponent filaments based on thermoplastic polyurethane (TPU) and doped with carbon nanotubes (CNTs) offer great potential due to their flexible mechanical properties. Through the core-conducting, bicomponent structure, the sensing material is protected from environmental factors such as surrounding conductive materials and external moisture. The insulating material, however, simultaneously complicates the contacting method in order to measure sensing changes in the conductive core. In this work, laser cutting is employed as a technology in order to expose the conductive core of the filaments. The filament is then coated with silver and mechanically crimped, providing both a conductive interface for the data acquisition device as well as a protective layer. Laser parameters (power 20–100 W and speed 5–50 mm/s) are investigated to identify the parameters with the best cutting properties for which the filaments are analyzed visually and electrically. This work provides a robust and reproducible method for contacting core-conducting TPU filaments for strain-sensing applications. This study shows that while the choice of laser parameter influences the morphology of the cut surface, its impact on the resulting linear resistivity is negligible.
{"title":"Contacting of Bicomponent TPU-Fibers with a Conductive Core: A Method for Data Acquisition and Analysis of the Electrical Properties","authors":"J. Ortega, Felix Krooß, Yuwei Stefan Li, Thomas Gries","doi":"10.3390/fib12050041","DOIUrl":"https://doi.org/10.3390/fib12050041","url":null,"abstract":"With the megatrend of digitalization, the demand for sensors in previously difficult-to-access scenarios is increasing. Filament-shaped sensors (FSS) are ideal for this demand, especially in applications in which the monitoring of textile structures is the focus. Electrically conductive bicomponent filaments based on thermoplastic polyurethane (TPU) and doped with carbon nanotubes (CNTs) offer great potential due to their flexible mechanical properties. Through the core-conducting, bicomponent structure, the sensing material is protected from environmental factors such as surrounding conductive materials and external moisture. The insulating material, however, simultaneously complicates the contacting method in order to measure sensing changes in the conductive core. In this work, laser cutting is employed as a technology in order to expose the conductive core of the filaments. The filament is then coated with silver and mechanically crimped, providing both a conductive interface for the data acquisition device as well as a protective layer. Laser parameters (power 20–100 W and speed 5–50 mm/s) are investigated to identify the parameters with the best cutting properties for which the filaments are analyzed visually and electrically. This work provides a robust and reproducible method for contacting core-conducting TPU filaments for strain-sensing applications. This study shows that while the choice of laser parameter influences the morphology of the cut surface, its impact on the resulting linear resistivity is negligible.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"184 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-08","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141001923","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
This paper investigates the durability of geopolymers and geopolymeric mortars made with metakaolin and alkaline activators, with and without a coconut fiber addition, after immersion for seven days into solutions of citric acid (1%, 2.5%, 5%, and 10%); hydrochloric acid (1%, 2.5%, 5%, and 10%); and sulfuric acid (1%, 2.5%, 5%, and 10%). The study focuses on mass changes, uniaxial compressive strength, flexural strength, and ultrasound pulse velocity measurements. X-ray diffraction and scanning electron microscopy are used to analyze the degradation products and microstructural changes. The aim is to assess the effect of acid exposure on the strength and stability of geopolymer materials and identify any protective effects of coconut fiber reinforcement. The samples are immersed in acid solutions of varying concentrations, and their mechanical properties are measured. The presence of coconut fibers slightly modifies the physical properties and the compressive strength, improving the mechanical flexural strength. Geopolymer and geopolymeric mortar materials experienced a weak decrease in strength when exposed to solutions of citric acid and a significant one when exposed to solutions of hydrochloric and sulfuric acids, attributed to depolymerization of the aluminosilicate binders. Brick waste geopolymeric mortars reinforced with coconut fibers showed the best performance in acid solutions with respect to geopolymers and quartz-rich sand geopolymeric mortars, suggesting a more stable cross-linked aluminosilicate geopolymer structure in this material.
{"title":"Acid Resistance of Metakaolin-Based Geopolymers and Geopolymeric Mortars Reinforced with Coconut Fibers","authors":"M. Lezzerini, Andrea Aquino, Stefano Pagnotta","doi":"10.3390/fib12050040","DOIUrl":"https://doi.org/10.3390/fib12050040","url":null,"abstract":"This paper investigates the durability of geopolymers and geopolymeric mortars made with metakaolin and alkaline activators, with and without a coconut fiber addition, after immersion for seven days into solutions of citric acid (1%, 2.5%, 5%, and 10%); hydrochloric acid (1%, 2.5%, 5%, and 10%); and sulfuric acid (1%, 2.5%, 5%, and 10%). The study focuses on mass changes, uniaxial compressive strength, flexural strength, and ultrasound pulse velocity measurements. X-ray diffraction and scanning electron microscopy are used to analyze the degradation products and microstructural changes. The aim is to assess the effect of acid exposure on the strength and stability of geopolymer materials and identify any protective effects of coconut fiber reinforcement. The samples are immersed in acid solutions of varying concentrations, and their mechanical properties are measured. The presence of coconut fibers slightly modifies the physical properties and the compressive strength, improving the mechanical flexural strength. Geopolymer and geopolymeric mortar materials experienced a weak decrease in strength when exposed to solutions of citric acid and a significant one when exposed to solutions of hydrochloric and sulfuric acids, attributed to depolymerization of the aluminosilicate binders. Brick waste geopolymeric mortars reinforced with coconut fibers showed the best performance in acid solutions with respect to geopolymers and quartz-rich sand geopolymeric mortars, suggesting a more stable cross-linked aluminosilicate geopolymer structure in this material.","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"16 22","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-05-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141055467","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Rene Alejandro Canceco de la Cruz, Caleb Carreño Gallardo, Alberto Díaz Díaz, Luis Adrian Zuñiga Aviles, Gabriel Plascencia Barrera, Jose Martin Herrera Ramirez
Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® is extensively used as a reinforcement in the security industry owing to its good ballistic properties. This investigation presents a mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® 29/phenolic resin with a polyvinyl butyral composite using a universal testing system. The methodology developed for the preparation of the coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupons’ thermoforming conditions or the reasons for the coupons’ dimensions (width, length and thickness).
{"title":"In-Plane Mechanical Characterization of a Kevlar® Composite","authors":"Rene Alejandro Canceco de la Cruz, Caleb Carreño Gallardo, Alberto Díaz Díaz, Luis Adrian Zuñiga Aviles, Gabriel Plascencia Barrera, Jose Martin Herrera Ramirez","doi":"10.3390/fib12050038","DOIUrl":"https://doi.org/10.3390/fib12050038","url":null,"abstract":"Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® is extensively used as a reinforcement in the security industry owing to its good ballistic properties. This investigation presents a mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® 29/phenolic resin with a polyvinyl butyral composite using a universal testing system. The methodology developed for the preparation of the coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupons’ thermoforming conditions or the reasons for the coupons’ dimensions (width, length and thickness).","PeriodicalId":503983,"journal":{"name":"Fibers","volume":"50 37","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-04-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140656678","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：