Annals of Occupational Hygiene最新文献

Exposure to cobalt in the hard metal industry entails severe adverse health effects, including lung cancer and hard metal fibrosis. The main aim of this study was to determine exposure air concentration levels of cobalt and tungsten for risk assessment and dose-response analysis in our medical investigations in a Swedish hard metal plant. We also present mass-based, particle surface area, and particle number air concentrations from stationary sampling and investigate the possibility of using these data as proxies for exposure measures in our study. Personal exposure full-shift measurements were performed for inhalable and total dust, cobalt, and tungsten, including personal real-time continuous monitoring of dust. Stationary measurements of inhalable and total dust, PM2.5, and PM10 was also performed and cobalt and tungsten levels were determined, as were air concentration of particle number and particle surface area of fine particles. The personal exposure levels of inhalable dust were consistently low (AM 0.15mg m(-3), range <0.023-3.0mg m(-3)) and below the present Swedish occupational exposure limit (OEL) of 10mg m(-3) The cobalt levels were low as well (AM 0.0030mg m(-3), range 0.000028-0.056mg m(-3)) and only 6% of the samples exceeded the Swedish OEL of 0.02mg m(-3) For continuous personal monitoring of dust exposure, the peaks ranged from 0.001 to 83mg m(-3) by work task. Stationary measurements showed lower average levels both for inhalable and total dust and cobalt. The particle number concentration of fine particles (AM 3000 p·cm(-3)) showed the highest levels at the departments of powder production, pressing and storage, and for the particle surface area concentrations (AM 7.6 µm(2)·cm(-3)) similar results were found. Correlating cobalt mass-based exposure measurements to cobalt stationary mass-based, particle area, and particle number concentrations by rank and department showed significant correlations for all measures except for particle number. Linear regression analysis of the same data showed statistically significant regression coefficients only for the mass-based aerosol measures. Similar results were seen for rank correlation in the stationary rig, and linear regression analysis implied significant correlation for mass-based and particle surface area measures. The mass-based air concentration levels of cobalt and tungsten in the hard metal plant in our study were low compared to Swedish OELs. Particle number and particle surface area concentrations were in the same order of magnitude as for other industrial settings. Regression analysis implied the use of stationary determined mass-based and particle surface area aerosol concentration as proxies for various exposure measures in our study.

Safety climate measurements can be used to proactively assess an organization's effectiveness in identifying and remediating work-related hazards, thereby reducing or preventing work-related ill health and injury. This review article focuses on construction-specific articles that developed and/or measured safety climate, assessed safety climate's relationship with other safety and health performance indicators, and/or used safety climate measures to evaluate interventions targeting one or more indicators of safety climate. Fifty-six articles met our inclusion criteria, 80% of which were published after 2008. Our findings demonstrate that researchers commonly defined safety climate as perception based, but the object of those perceptions varies widely. Within the wide range of indicators used to measure safety climate, safety policies, procedures, and practices were the most common, followed by general management commitment to safety. The most frequently used indicators should and do reflect that the prevention of work-related ill health and injury depends on both organizational and employee actions. Safety climate scores were commonly compared between groups (e.g. management and workers, different trades), and often correlated with subjective measures of safety behavior rather than measures of ill health or objective safety and health outcomes. Despite the observed limitations of current research, safety climate has been promised as a useful feature of research and practice activities to prevent work-related ill health and injury. Safety climate survey data can reveal gaps between management and employee perceptions, or between espoused and enacted policies, and trigger communication and action to narrow those gaps. The validation of safety climate with safety and health performance data offers the potential for using safety climate measures as a leading indicator of performance. We discuss these findings in relation to the related concept of safety culture and offer suggestions for future research and practice including (i) deriving a common definition of safety climate, (ii) developing and testing construction-specific indicators of safety climate, and (iii) focusing on construction-specific issues such as the transient workforce, subcontracting, work organization, and induction/acculturation processes.

A series of laboratory tests were conducted to assess the effects of Fe-containing fuel additives on aerosols emitted by a diesel engine retrofitted with a sintered metal filter (SMF) system. Emission measurements performed upstream and downstream of the SMF system were compared, for cases when the engine was fueled with neat ultralow sulfur diesel (ULSD) and with ULSD treated with two formulations of additives containing Fe-based catalysts. The effects were assessed for four steady-state engine operating conditions and one transient cycle. The results showed that the SMF system reduced the average total number and surface area concentrations of aerosols by more than 100-fold. The total mass and elemental carbon results confirmed that the SMF system was indeed very effective in the removal of diesel aerosols. When added at the recommended concentrations (30 p.p.m. of iron), the tested additives had minor adverse impacts on the number, surface area, and mass concentrations of filter-out (FOut) aerosols. For one of the test cases, the additives may have contributed to measurable concentrations of engine-out (EOut) nucleation mode aerosols. The additives had only a minor impact on the concentration and size distribution of volatile and semi-volatile FOut aerosols. Metal analysis showed that the introduction of Fe with the additives substantially increased Fe concentration in the EOut, but the SMF system was effective in removal of Fe-containing aerosols. The FOut Fe concentrations for all three tested fuels were found to be much lower than the corresponding EOut Fe concentrations for the case of untreated ULSD fuel. The results support recommendations that these additives should not be used in diesel engines unless they are equipped with exhaust filtration systems. Since the tested SMF system was found to be very efficient in removing Fe introduced by the additives, the use of these additives should not result in a measurable increase in emissions of de novo generated Fe-containing aerosols. The findings from this study should promote a better understanding of the benefits and challenges of using sintered metal systems and fuel additives to control the exposure of underground miners and other workers to diesel aerosols and gases.

A laboratory testing system was developed to systematically characterize the dust generation rate and size-dependent crystalline silica content when cutting or shaping silica containing materials. The tests of cutting fiber cement siding in this system verify that it provides high test repeatability, making it suitable for the targeted characterizations. The mass-based size distributions obtained from a gravimetric-based instrument and a direct reading instrument both show bimodal lognormal distributions with a larger mode ~13 µm and another mode <5 µm for the dusts from cutting four different brands of fiber cement siding. The generation rates of respirable dust obtained from the two instruments are comparable, and the results from each instrument are similar for the four brands. The silica content in the airborne dusts, however, strongly depends on the amount of silica used in the respective product. It is also observed that the silica content in the airborne dust from cutting the four brands of fiber cement siding showed the same trend of an increase with the aerodynamic diameter of the dust, approaching the silica content levels found in their respective bulk samples. Combining the results for both the dust size distribution and size-dependent silica content, it is found that most of the respirable crystalline silica (RCS) resides in the dust ~2.5 µm in aerodynamic diameter. These results would help guide the development of specific engineering control measures targeted at lowering workers' exposure to RCS while cutting fiber cement siding. With the high repeatability using the laboratory testing system, the dust generation rate could then be characterized under different operating conditions, and with the deployment of various engineering control measures. This would greatly facilitate the systematic evaluation of the control effectiveness and the selection of the optimal control solutions for field trials.

Quantifying exposure and dose to manganese (Mn) containing airborne particles in welding fume presents many challenges. Common biological markers such as Mn in blood or Mn in urine have not proven to be practical biomarkers even in studies where positive associations were observed. However, hair Mn (MnH) as a biomarker has the advantage over blood and urine that it is less influenced by short-term variability of Mn exposure levels because of its slow growth rate. The objective of this study was to determine whether hair can be used as a biomarker for welders exposed to manganese. Hair samples (1cm) were collected from 47 welding school students and individual air Mn (MnA) exposures were measured for each subject. MnA levels for all days were estimated with a linear mixed model using welding type as a predictor. A 30-day time-weighted average MnA (MnA30d) exposure level was calculated for each hair sample. The association between MnH and MnA30d levels was then assessed. A linear relationship was observed between log-transformed MnA30d and log-transformed MnH. Doubling MnA30d exposure levels yields a 20% (95% confidence interval: 11-29%) increase in MnH. The association was similar for hair washed following two different wash procedures designed to remove external contamination. Hair shows promise as a biomarker for inhaled Mn exposure given the presence of a significant linear association between MnH and MnA30d levels.

Many ailments can be linked to exposure to indoor airborne fungus. However, obtaining a precise measurement of airborne fungal levels is complicated partly due to indoor air fluctuations and non-standardized techniques. Electrostatic dust collector (EDC) sampling devices have been used to measure a wide range of airborne analytes, including endotoxins, allergens, β-glucans, and microbial DNA in various indoor environments. In contrast, viable mold contamination has only been assessed in highly contaminated environments such as farms and archive buildings. This study aimed to assess the use of EDCs, compared with repeated air-impactor measurements, to assess airborne viable fungal flora in moderately contaminated indoor environments. Indoor airborne fungal flora was cultured from EDCs and daily air-impaction samples collected in an office building and a daycare center. The quantitative fungal measurements obtained using a single EDC significantly correlated with the cumulative measurement of nine daily air impactions. Both methods enabled the assessment of fungal exposure, although a few differences were observed between the detected fungal species and the relative quantity of each species. EDCs were also used over a 32-month period to monitor indoor airborne fungal flora in a hospital office building, which enabled us to assess the impact of outdoor events (e.g. ground excavations) on the fungal flora levels on the indoor environment. In conclusion, EDC-based measurements provided a relatively accurate profile of the viable airborne flora present during a sampling period. In particular, EDCs provided a more representative assessment of fungal levels compared with single air-impactor sampling. The EDC technique is also simpler than performing repetitive air-impaction measures over the course of several consecutive days. EDC is a versatile tool for collecting airborne samples and was efficient for measuring mold levels in indoor environments.

Introduction: To date, occupational exposure assessment of electromagnetic fields (EMF) has relied on occupation-based measurements and exposure estimates. However, misclassification due to between-worker variability remains an unsolved challenge. A source-based approach, supported by detailed subject data on determinants of exposure, may allow for a more individualized exposure assessment. Detailed information on the use of occupational sources of exposure to EMF was collected as part of the INTERPHONE-INTEROCC study. To support a source-based exposure assessment effort within this study, this work aimed to construct a measurement database for the occupational sources of EMF exposure identified, assembling available measurements from the scientific literature.

Methods: First, a comprehensive literature search was performed for published and unpublished documents containing exposure measurements for the EMF sources identified, a priori as well as from answers of study subjects. Then, the measurements identified were assessed for quality and relevance to the study objectives. Finally, the measurements selected and complementary information were compiled into an Occupational Exposure Measurement Database (OEMD).

Results: Currently, the OEMD contains 1624 sets of measurements (>3000 entries) for 285 sources of EMF exposure, organized by frequency band (0 Hz to 300 GHz) and dosimetry type. Ninety-five documents were selected from the literature (almost 35% of them are unpublished technical reports), containing measurements which were considered informative and valid for our purpose. Measurement data and complementary information collected from these documents came from 16 different countries and cover the time period between 1974 and 2013.

Conclusion: We have constructed a database with measurements and complementary information for the most common sources of exposure to EMF in the workplace, based on the responses to the INTERPHONE-INTEROCC study questionnaire. This database covers the entire EMF frequency range and represents the most comprehensive resource of information on occupational EMF exposure. It is available at www.crealradiation.com/index.php/en/databases.

Procedures and equations reported in ISO 9920 for the correction of basic thermophysical clothing properties taking into account pumping effect and air movement are very different from those used by the Predicted Heat Strain (PHS) model in ISO 7933. To study the effect of these differences on the assessment of hot environments using the PHS model, an analysis focusing on the modelling of the dynamic thermal insulation and the vapour resistance of the clothing reported in ISO 9920 and ISO 7933 standards will be discussed in this paper. The results are useful evidence to start a discussion on the best practice for dealing with clothing thermophysical properties and underline the need to harmonize the entire set of standards in the field of the Ergonomics of the Thermal Environment. ISO 7933 is presently under revision.

The state-of-the-art for personal sampling for inhalable aerosol hazards is constrained by issues of sampler cost and complexity; these issues have limited the adoption and use of some samplers by practicing hygienists. Thus, despite the known health effects of inhalable aerosol hazards, personal exposures are routinely assessed for only a small fraction of the at-risk workforce. To address the limitations of current technologies for inhalable aerosol sampling, a disposable inhalable aerosol sampler was developed and evaluated in the laboratory. The new sampler is designed to be less expensive and simpler to use than existing technologies. The sampler incorporates a lightweight internal capsule fused to the sampling filter. This capsule-filter assembly allows for the inclusion of particles deposited on the internal walls and inlet, thus minimizing the need to wash or wipe the interior sampling cassette when conducting gravimetric analyses. Sampling efficiency and wall losses were tested in a low-velocity wind tunnel with particles ranging from 9.5 to 89.5 μm. The results were compared to the proposed low-velocity inhalability criterion as well as published data on the IOM sampler. Filter weight stability and time-to-equilibrium were evaluated as these factors affect the practicality of a design. Preliminary testing of the new sampler showed good agreement with both the IOM and the proposed low-velocity inhalability curve. The capsule and filter assemblies reached equilibrium within 25h of manufacturing when conditioned at elevated temperatures. After reaching equilibrium, the capsule-filter assemblies were stable within 0.01mg.