A continued challenge to engine combustion simulation is predicting the impact of fuel-composition variability on performance and emissions. Diesel fuel properties, such as cetane number, aromatic content and volatility, significantly impact combustion phasing and emissions. Capturing such fuel property effects is critical to predictive engine combustion modeling. In this work, we focus on accurately modeling diesel fuel effects on combustion and emissions. Engine modeling is performed with 3D CFD using multi-component fuel models, and detailed chemical kinetics. Diesel FACE fuels (Fuels for Advanced Combustion Engines) have been considered in this study as representative of street fuel variability. The CFD modeling simulates experiments performed at Oak Ridge National Laboratory (ORNL) [1] using the diesel FACE fuels in a light-duty single-cylinder direct-injection engine. These ORNL experiments evaluated fuel effects on combustion phasing and emissions. The actual FACE fuels are used directly in engine experiments while surrogate-fuel blends that are tailored to represent the FACE fuels are used in the modeling. The 3D CFD simulations include spray dynamics and turbulent mixing. We first establish a methodology to define a model fuel that captures diesel fuel property effects. Such a model should be practically useful in terms of acceptable computational turnaround time in engine CFD simulations, even as we use sophisticated fuel surrogates and detailed chemistry. Towards these goals, multi-component fuel surrogates have been developed for several FACE fuels, where the associated kinetics mechanisms are available in a model-fuels database. A surrogate blending technique has been employed to generate the multi-component surrogates, so that they match selected FACE fuel properties such as cetane number, chemical classes such as aromatics content, T50 and T90 distillation points, lower heating value and H/C molar ratio. Starting from a well validated comprehensive gas-phase chemistry, an automated method has been used for extracting a reduced chemistry that satisfies desired accuracy and is reasonable for use in CFD. Results show the level of modeling necessary to capture fuel-property trends under these widely varying engine conditions.
{"title":"Modeling Fuel Effects in a Diesel Engine Using Multi-Component Fuel Surrogates in CFD","authors":"K. Puduppakkam, C. Naik, E. Meeks","doi":"10.1115/ICEF2018-9747","DOIUrl":"https://doi.org/10.1115/ICEF2018-9747","url":null,"abstract":"A continued challenge to engine combustion simulation is predicting the impact of fuel-composition variability on performance and emissions. Diesel fuel properties, such as cetane number, aromatic content and volatility, significantly impact combustion phasing and emissions. Capturing such fuel property effects is critical to predictive engine combustion modeling. In this work, we focus on accurately modeling diesel fuel effects on combustion and emissions. Engine modeling is performed with 3D CFD using multi-component fuel models, and detailed chemical kinetics. Diesel FACE fuels (Fuels for Advanced Combustion Engines) have been considered in this study as representative of street fuel variability. The CFD modeling simulates experiments performed at Oak Ridge National Laboratory (ORNL) [1] using the diesel FACE fuels in a light-duty single-cylinder direct-injection engine. These ORNL experiments evaluated fuel effects on combustion phasing and emissions. The actual FACE fuels are used directly in engine experiments while surrogate-fuel blends that are tailored to represent the FACE fuels are used in the modeling. The 3D CFD simulations include spray dynamics and turbulent mixing.\u0000 We first establish a methodology to define a model fuel that captures diesel fuel property effects. Such a model should be practically useful in terms of acceptable computational turnaround time in engine CFD simulations, even as we use sophisticated fuel surrogates and detailed chemistry. Towards these goals, multi-component fuel surrogates have been developed for several FACE fuels, where the associated kinetics mechanisms are available in a model-fuels database. A surrogate blending technique has been employed to generate the multi-component surrogates, so that they match selected FACE fuel properties such as cetane number, chemical classes such as aromatics content, T50 and T90 distillation points, lower heating value and H/C molar ratio. Starting from a well validated comprehensive gas-phase chemistry, an automated method has been used for extracting a reduced chemistry that satisfies desired accuracy and is reasonable for use in CFD. Results show the level of modeling necessary to capture fuel-property trends under these widely varying engine conditions.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"8 5 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130798896","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
K. Partridge, P. R. Jha, Hamidreza Mahabadipour, K. Srinivasan, S. Krishnan
Computational simulations of engine combustion processes are increasingly relied upon to lead the design of advanced IC engines. Both computational fluid dynamics (CFD) simulations as well as thermodynamics-based phenomenological 0D or 1D gas dynamics simulations are examples of current simulation strategies. Before simulations can be utilized to guide the design process, they must be validated with experimental results. Typically, the experimental data used for validation of computational simulations include in-cylinder pressure and apparent heat release rate (AHRR) histories. However, the process of comparison of experimental and simulated pressure and AHRR curves is largely qualitative; therefore, the validation process is mostly visual. In the present work, the authors introduce a framework for quantifying uncertainties in experimental pressure data, as well as uncertainties in the “average” AHRR curve that is derived from ensemble-averaged cylinder pressure histories. Predicted AHRR curves from CFD simulations are also quantitatively compared with the experimental AHRR bounded by “uncertainty bands” in the present work.
{"title":"Systematic Uncertainty Considerations in the Comparison of Experimental and Computed Cylinder Pressure and Heat Release Histories","authors":"K. Partridge, P. R. Jha, Hamidreza Mahabadipour, K. Srinivasan, S. Krishnan","doi":"10.1115/ICEF2018-9707","DOIUrl":"https://doi.org/10.1115/ICEF2018-9707","url":null,"abstract":"Computational simulations of engine combustion processes are increasingly relied upon to lead the design of advanced IC engines. Both computational fluid dynamics (CFD) simulations as well as thermodynamics-based phenomenological 0D or 1D gas dynamics simulations are examples of current simulation strategies. Before simulations can be utilized to guide the design process, they must be validated with experimental results. Typically, the experimental data used for validation of computational simulations include in-cylinder pressure and apparent heat release rate (AHRR) histories. However, the process of comparison of experimental and simulated pressure and AHRR curves is largely qualitative; therefore, the validation process is mostly visual. In the present work, the authors introduce a framework for quantifying uncertainties in experimental pressure data, as well as uncertainties in the “average” AHRR curve that is derived from ensemble-averaged cylinder pressure histories. Predicted AHRR curves from CFD simulations are also quantitatively compared with the experimental AHRR bounded by “uncertainty bands” in the present work.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"1988 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128561776","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
H. Oh, Jinwook Son, Juhun Lee, S. Woo, Youngnam Kim, Seungwoo Hong
Experimental study on knocking characteristics in a direct injection turbo-charged gasoline engine was carried out. The thermodynamic analysis was conducted to investigate effects of the combustion phasing and the burning rate on the knocking behavior. The localization of knock events and the characterization of the early flame kernel propagation were conducted with the fiber optic sensor. The advanced combustion phasing and the slower combustion speed generally increased the knocking probability. However, not only quasi-dimensional thermodynamic combustion characteristics but also the spatial parameter such as the flame propagation direction significantly affected the knocking occurrence. From the fiber optic sensor test results, knocking onset location was found to be closely correlated with the flame propagation direction and mainly observed in the opposite side to the main flame propagation direction. The flame propagation direction leaning to the exhaust side was identified to be favorable for the knocking mitigation because the end gas location on hotter exhaust side could be avoided. Engine tests for various squish designs and tumble port designs were implemented to study the effect of the in-cylinder flow, which significantly affects previously discussed knocking-related parameters. As a result, tumble and squish flow significantly increased combustion speed and advanced combustion phasing. Fuel consumption could be also reduced due to suppressed knocking combustion. In addition, new tumble port design enabled the flame propagation to have favorable leaning direction.
{"title":"Effect of Combustion Characteristics on Knocking in a Direct Injection Turbo-Charged Gasoline Engine","authors":"H. Oh, Jinwook Son, Juhun Lee, S. Woo, Youngnam Kim, Seungwoo Hong","doi":"10.1115/ICEF2018-9524","DOIUrl":"https://doi.org/10.1115/ICEF2018-9524","url":null,"abstract":"Experimental study on knocking characteristics in a direct injection turbo-charged gasoline engine was carried out. The thermodynamic analysis was conducted to investigate effects of the combustion phasing and the burning rate on the knocking behavior. The localization of knock events and the characterization of the early flame kernel propagation were conducted with the fiber optic sensor.\u0000 The advanced combustion phasing and the slower combustion speed generally increased the knocking probability. However, not only quasi-dimensional thermodynamic combustion characteristics but also the spatial parameter such as the flame propagation direction significantly affected the knocking occurrence. From the fiber optic sensor test results, knocking onset location was found to be closely correlated with the flame propagation direction and mainly observed in the opposite side to the main flame propagation direction. The flame propagation direction leaning to the exhaust side was identified to be favorable for the knocking mitigation because the end gas location on hotter exhaust side could be avoided.\u0000 Engine tests for various squish designs and tumble port designs were implemented to study the effect of the in-cylinder flow, which significantly affects previously discussed knocking-related parameters. As a result, tumble and squish flow significantly increased combustion speed and advanced combustion phasing. Fuel consumption could be also reduced due to suppressed knocking combustion. In addition, new tumble port design enabled the flame propagation to have favorable leaning direction.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"67 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"127515197","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
R. Gao, Li Shen, Kwee-Yan Teh, Penghui Ge, Fengnian Zhao, D. Hung
Proper Orthogonal Decomposition (POD) offers an approach to quantify cycle-to-cycle variation (CCV) of the flow field inside the internal combustion engine cylinder. POD decomposes instantaneous flow fields (also called snapshots) into a series of orthonormal flow patterns (called POD modes) and the corresponding mode coefficients. The POD modes are rank-ordered by decreasing kinetic energy content, and the low-order, high-energy modes are interpreted as constituting the large-scale coherent flow structure that varies from engine cycle to engine cycle. Various POD-based analysis techniques have thus been proposed to characterize engine flow field CCV using these low-order modes. The validity of such POD-based analyses rests, as a matter of course, on the reliability of the underlying POD results (modes and coefficients). Yet a POD mode can be disproportionately skewed by a single outlier snapshot within a large data set, and an algorithm exists to define and identify such outliers. In this paper, the effects of a candidate outlier snapshot on the results of POD-based conditional averaging and quadruple POD analyses are examined for two sets of crank angle-resolved flow fields on the mid-tumble plane of an optical engine cylinder recorded by high-speed particle image velocimetry. The results with and without the candidate outlier are compared and contrasted. In the case of POD-based conditional averaging, the presence of the outlier scrambles the composition of snapshot subsets that define large-scale flow pattern variations, and thus substantially alters the coherent flow structures that are identified; for quadruple POD, the shape of coherent structures as well as the number of modes to define them are not significantly affected by the outlier.
{"title":"Effects of Outlier Flow Field on the Characteristics of In-Cylinder Coherent Structures Identified by POD-Based Conditional Averaging and Quadruple POD","authors":"R. Gao, Li Shen, Kwee-Yan Teh, Penghui Ge, Fengnian Zhao, D. Hung","doi":"10.1115/ICEF2018-9561","DOIUrl":"https://doi.org/10.1115/ICEF2018-9561","url":null,"abstract":"Proper Orthogonal Decomposition (POD) offers an approach to quantify cycle-to-cycle variation (CCV) of the flow field inside the internal combustion engine cylinder. POD decomposes instantaneous flow fields (also called snapshots) into a series of orthonormal flow patterns (called POD modes) and the corresponding mode coefficients. The POD modes are rank-ordered by decreasing kinetic energy content, and the low-order, high-energy modes are interpreted as constituting the large-scale coherent flow structure that varies from engine cycle to engine cycle. Various POD-based analysis techniques have thus been proposed to characterize engine flow field CCV using these low-order modes. The validity of such POD-based analyses rests, as a matter of course, on the reliability of the underlying POD results (modes and coefficients). Yet a POD mode can be disproportionately skewed by a single outlier snapshot within a large data set, and an algorithm exists to define and identify such outliers. In this paper, the effects of a candidate outlier snapshot on the results of POD-based conditional averaging and quadruple POD analyses are examined for two sets of crank angle-resolved flow fields on the mid-tumble plane of an optical engine cylinder recorded by high-speed particle image velocimetry. The results with and without the candidate outlier are compared and contrasted. In the case of POD-based conditional averaging, the presence of the outlier scrambles the composition of snapshot subsets that define large-scale flow pattern variations, and thus substantially alters the coherent flow structures that are identified; for quadruple POD, the shape of coherent structures as well as the number of modes to define them are not significantly affected by the outlier.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"4 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"114327896","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Diesel engines have been widely used due to the higher reliability and superior fuel conversion efficiency. However, they still generate significant amount of carbon dioxide (CO2) and particulate matter (PM) emissions. Natural gas is a low carbon and clean fuel that generates less CO2 and PM emissions than diesel during combustion. Replacing diesel by natural gas in internal combustion engines help reduce both CO2 and PM emissions. Natural gas – diesel dual fuel combustion is a practical and efficient way to replace diesel by natural gas in internal combustion engines. One concern for dual fuel combustion engines is the diesel injector tip temperature increase with increasing natural gas fraction. This paper reports an experimental investigation on the diesel injector tip temperature variation and combustion performance of a natural gas – diesel dual fuel engine at medium and high load conditions. The natural gas fraction was changed from zero to 90% in the experiment. The results suggest that the injector tip temperature increased with increasing natural gas fraction at a given diesel injection timing or with advancing the diesel injection timing at a given natural gas fraction. However, the injector tip temperature never exceeded 250 °C in the whole experimental range. The effect of natural gas fraction on combustion performance depended on engine load and diesel injection timing.
{"title":"Injector Tip Temperature and Combustion Performance of a Natural Gas-Diesel Dual Fuel Engine at Medium and High Load Conditions","authors":"Hongsheng Guo, B. Liko","doi":"10.1115/ICEF2018-9664","DOIUrl":"https://doi.org/10.1115/ICEF2018-9664","url":null,"abstract":"Diesel engines have been widely used due to the higher reliability and superior fuel conversion efficiency. However, they still generate significant amount of carbon dioxide (CO2) and particulate matter (PM) emissions. Natural gas is a low carbon and clean fuel that generates less CO2 and PM emissions than diesel during combustion. Replacing diesel by natural gas in internal combustion engines help reduce both CO2 and PM emissions. Natural gas – diesel dual fuel combustion is a practical and efficient way to replace diesel by natural gas in internal combustion engines. One concern for dual fuel combustion engines is the diesel injector tip temperature increase with increasing natural gas fraction.\u0000 This paper reports an experimental investigation on the diesel injector tip temperature variation and combustion performance of a natural gas – diesel dual fuel engine at medium and high load conditions. The natural gas fraction was changed from zero to 90% in the experiment. The results suggest that the injector tip temperature increased with increasing natural gas fraction at a given diesel injection timing or with advancing the diesel injection timing at a given natural gas fraction. However, the injector tip temperature never exceeded 250 °C in the whole experimental range. The effect of natural gas fraction on combustion performance depended on engine load and diesel injection timing.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"32 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"129577356","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Marine diesel engines usually operate on a highly boosted intake pressure. The reciprocating feature of diesel engines and the continuous flow operation characteristics of the turbocharger (TC) make the matching between the turbocharger and diesel engine very challenging. Sequential turbocharging (STC) technology is recognized as an effective approach in improving the fuel economy and exhaust emissions especially at low speed and high torque when a single stage turbocharger is not able to boost the intake air to the pressure needed. The application of STC technology also extends engine operation toward a wider range than that using a single-stage turbocharger. This research experimentally investigated the potential of a STC system in improving the performance of a TBD234V12 model marine diesel engine originally designed to operate on a single-stage turbocharger. The STC system examined consisted of a small (S) turbocharger and a large (L) turbocharger which were installed in parallel. Such a system can operate on three boosting modes noted as 1TC-S, 1TC-L and 2TC. A rule-based control algorithm was developed to smoothly switch the STC operation mode using engine speed and load as references. The potential of the STC system in improving the performance of this engine was experimentally examined over a wide range of engine speed and load. When operated at the standard propeller propulsion cycle, the application of the STC system reduced the brake specific fuel consumption (BSFC) by 3.12% averagely. The average of the exhaust temperature before turbine was decreased by 50°C. The soot and oxides of nitrogen (NOx) emissions were reduced respectively. The examination of the engine performance over an entire engine speed and torque range demonstrated the super performance of the STC system in extending the engine operation toward the high torque at low speed (900 to 1200 RPM) while further improving the fuel economy as expected. The engine maximum torque at 900 rpm was increased from 1680Nm to 2361 Nm (40.5%). The average BSFC over entire working area was improved by 7.4%. The BSFC at low load and high torque was significantly decreased. The application of the STC system also decreased the average NOx emissions by 31.5% when examined on the propeller propulsion cycle.
{"title":"An Experimental Study on Fuel Economy Improvement of a Marine Diesel Engine Using a Sequential Turbocharging System","authors":"Hechun Wang, Xiannan Li, Yinyan Wang, Hailin Li","doi":"10.1115/ICEF2018-9569","DOIUrl":"https://doi.org/10.1115/ICEF2018-9569","url":null,"abstract":"Marine diesel engines usually operate on a highly boosted intake pressure. The reciprocating feature of diesel engines and the continuous flow operation characteristics of the turbocharger (TC) make the matching between the turbocharger and diesel engine very challenging. Sequential turbocharging (STC) technology is recognized as an effective approach in improving the fuel economy and exhaust emissions especially at low speed and high torque when a single stage turbocharger is not able to boost the intake air to the pressure needed. The application of STC technology also extends engine operation toward a wider range than that using a single-stage turbocharger.\u0000 This research experimentally investigated the potential of a STC system in improving the performance of a TBD234V12 model marine diesel engine originally designed to operate on a single-stage turbocharger. The STC system examined consisted of a small (S) turbocharger and a large (L) turbocharger which were installed in parallel. Such a system can operate on three boosting modes noted as 1TC-S, 1TC-L and 2TC. A rule-based control algorithm was developed to smoothly switch the STC operation mode using engine speed and load as references. The potential of the STC system in improving the performance of this engine was experimentally examined over a wide range of engine speed and load. When operated at the standard propeller propulsion cycle, the application of the STC system reduced the brake specific fuel consumption (BSFC) by 3.12% averagely. The average of the exhaust temperature before turbine was decreased by 50°C. The soot and oxides of nitrogen (NOx) emissions were reduced respectively. The examination of the engine performance over an entire engine speed and torque range demonstrated the super performance of the STC system in extending the engine operation toward the high torque at low speed (900 to 1200 RPM) while further improving the fuel economy as expected. The engine maximum torque at 900 rpm was increased from 1680Nm to 2361 Nm (40.5%). The average BSFC over entire working area was improved by 7.4%. The BSFC at low load and high torque was significantly decreased. The application of the STC system also decreased the average NOx emissions by 31.5% when examined on the propeller propulsion cycle.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"33 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"128125292","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Mohammadrasool Morovatiyan, M. Shahsavan, M. Shen, J. H. Mack
Lean-burn engines are important due to their ability to reduce emissions, increase fuel efficiency, and mitigate engine knock. In this study, the surface roughness of spark plug electrodes is investigated as a potential avenue to extend the lean flammability limit of natural gas. A nano-/micro-morphology modification is applied on surface of the spark plug electrode to increase its surface roughness. High-speed Z-type Schlieren visualization is used to investigate the effect of the electrode surface roughness on the spark ignition process in a premixed methane-air charge at different lean equivalence ratios. In order to observe the onset of ignition and flame kernel behavior, experiments were conducted in an optically accessible constant volume combustion chamber at ambient pressures and temperatures. The results indicate that the lean flammability limit of spark-ignited methane can be lowered by modulating the surface roughness of the spark plug electrode.
{"title":"Investigation of the Effect of Electrode Surface Roughness on Spark Ignition","authors":"Mohammadrasool Morovatiyan, M. Shahsavan, M. Shen, J. H. Mack","doi":"10.1115/ICEF2018-9691","DOIUrl":"https://doi.org/10.1115/ICEF2018-9691","url":null,"abstract":"Lean-burn engines are important due to their ability to reduce emissions, increase fuel efficiency, and mitigate engine knock. In this study, the surface roughness of spark plug electrodes is investigated as a potential avenue to extend the lean flammability limit of natural gas. A nano-/micro-morphology modification is applied on surface of the spark plug electrode to increase its surface roughness. High-speed Z-type Schlieren visualization is used to investigate the effect of the electrode surface roughness on the spark ignition process in a premixed methane-air charge at different lean equivalence ratios. In order to observe the onset of ignition and flame kernel behavior, experiments were conducted in an optically accessible constant volume combustion chamber at ambient pressures and temperatures. The results indicate that the lean flammability limit of spark-ignited methane can be lowered by modulating the surface roughness of the spark plug electrode.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"603 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"130458980","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
B. Bihari, M. Biruduganti, Roberto Torelli, D. Singleton
Lean-burn combustion dominates the current reciprocating engine R&D efforts due to its inherent benefits of high BTE and low emissions. The ever-increasing push for high power densities necessitates high boost pressures. Therefore, the reliability and durability of ignition systems face greater challenges. In this study, four ignition systems, namely, stock Capacitive discharge ignition (CDI), Laser ignition, Flame jet ignition (FJI), and Nano-pulse delivery (NPD) ignition were tested using a single cylinder natural gas engine. Engine performance and emissions characteristics are presented highlighting the benefits and limitations of respective ignition systems. Optical tools enabled delving into the ignition delay period and assisted with some characterization of the spark and its impact on subsequent processes. It is evident that advanced ignition systems such as Lasers, Flame-jets and Nano-pulse delivery enable extension of the lean ignition limits of fuel/air mixtures compared to base CDI system.
{"title":"Performance Characterization of Alternative Ignition Systems Using Optical Tools in Natural Gas Engines","authors":"B. Bihari, M. Biruduganti, Roberto Torelli, D. Singleton","doi":"10.1115/ICEF2018-9704","DOIUrl":"https://doi.org/10.1115/ICEF2018-9704","url":null,"abstract":"Lean-burn combustion dominates the current reciprocating engine R&D efforts due to its inherent benefits of high BTE and low emissions. The ever-increasing push for high power densities necessitates high boost pressures. Therefore, the reliability and durability of ignition systems face greater challenges. In this study, four ignition systems, namely, stock Capacitive discharge ignition (CDI), Laser ignition, Flame jet ignition (FJI), and Nano-pulse delivery (NPD) ignition were tested using a single cylinder natural gas engine. Engine performance and emissions characteristics are presented highlighting the benefits and limitations of respective ignition systems. Optical tools enabled delving into the ignition delay period and assisted with some characterization of the spark and its impact on subsequent processes. It is evident that advanced ignition systems such as Lasers, Flame-jets and Nano-pulse delivery enable extension of the lean ignition limits of fuel/air mixtures compared to base CDI system.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"10 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124095402","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late-combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.
{"title":"Experimental Investigation of a Heavy-Duty CI Engine Retrofitted to Natural Gas SI Operation","authors":"Jinlong Liu, Hemanth Bommisetty, C. Dumitrescu","doi":"10.1115/ICEF2018-9611","DOIUrl":"https://doi.org/10.1115/ICEF2018-9611","url":null,"abstract":"Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late-combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"226 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"122372196","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The Achates Power Inc. (API) Opposed Piston (OP) Engine architecture provides fundamental advantages that increase thermal efficiency over current poppet valve 4 stroke engines. In this paper, combustion performance of diesel and gasoline compression ignition (GCI) combustion in a medium duty, OP engine are shown. By using GCI, NOx and/or soot reductions can be seen compared to diesel combustion at similar or increased thermal efficiencies. The results also show that high combustion efficiency can be achieved with GCI combustion with acceptable noise and stability over the same load range as diesel combustion in an OP engine.
与目前的四冲程锥阀发动机相比，Achates Power Inc. (API)的对置活塞(OP)发动机结构具有提高热效率的基本优势。本文研究了柴油和汽油压缩点火(GCI)燃烧在中等负荷柴油机上的燃烧性能。通过使用GCI，与柴油燃烧相比，在相似或更高的热效率下，可以看到氮氧化物和/或烟尘的减少。结果还表明，在相同的负荷范围内，GCI燃烧可以达到高的燃烧效率，并且具有可接受的噪声和稳定性，与OP发动机中的柴油燃烧相同。
{"title":"Experimental Comparison of GCI and Diesel Combustion in a Medium-Duty Opposed-Piston Engine","authors":"R. Hanson, Ashwin Salvi, F. Redon, G. Regner","doi":"10.1115/ICEF2018-9701","DOIUrl":"https://doi.org/10.1115/ICEF2018-9701","url":null,"abstract":"The Achates Power Inc. (API) Opposed Piston (OP) Engine architecture provides fundamental advantages that increase thermal efficiency over current poppet valve 4 stroke engines. In this paper, combustion performance of diesel and gasoline compression ignition (GCI) combustion in a medium duty, OP engine are shown.\u0000 By using GCI, NOx and/or soot reductions can be seen compared to diesel combustion at similar or increased thermal efficiencies. The results also show that high combustion efficiency can be achieved with GCI combustion with acceptable noise and stability over the same load range as diesel combustion in an OP engine.","PeriodicalId":441369,"journal":{"name":"Volume 1: Large Bore Engines; Fuels; Advanced Combustion","volume":"10 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2018-11-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"124950755","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：