Acta Stomatologica Croatica最新文献

Objective: The aim of this study was to compare the light transmission of monowave and polywave-curing devices by a bulk-fill composite containing only camphorquinone as a photoinitiator.

Materials and methods: Three light-curing devices were used to cure bulk-fill composite QuiXfil: one monowave (Translux® Wave) and two polywave (VALO Cordless and Bluephase® PowerCure. The NIST-calibrated spectrometer (MARC Resin Calibrator, BlueLight Analytics Inc.) was used to measure the incident and transmitted light through a 2-mm composite specimen over 20 s. Light transmittance was calculated from the ratio of the amount of transmitted and incident light. For data analysis (ANOVA, α = 0.05), total irradiation of the entire spectrum, irradiation with wavelengths of 360-420 nm for the violet spectrum, and 420-540 nm for the blue spectrum were selected.

Results: Monowave curing unit Translux® Wave had the lowest light transmission (13.78 ± 0.5%), similar to the violet light transmission of polywave devices (12.02 ± 0.94% and 13.81 ± 1.72% for Valo Cordless and Bluephase PowerCure, respectively). Blue light transmittance (32.15-23.70%) was more than twofold higher than for the wavelengths in the violet region of the spectrum (13.81-12.02%) for the two polywave devices. VALO Cordless showed the highest total and blue light transmission (p<0.001). There was no significant difference in the transmission of the violet part of the spectrum between VALO Cordless and Bluephase® PowerCure (p = 0.465).

Conclusion: Within the limitations of this study, we could conclude that polywave curing devices can be used for the polymerization of the bulk-fill composite with camphorquinone as the sole photoinitiator.

Objectives: This study aimed to determine the sex and estimate the age of individuals by analysing Raman spectra obtained from extracted teeth dentine.

Material and methods: A total of 25 male and 26 female extracted teeth were collected, disinfected, and fixed in auto acrylate before being cut near the cervical margin. The inclusion criteria were non endodontically treated teeth with the cervical third of the tooth crown preserved. The exposed dentine was recorded using a Raman spectrometer, with 100 scans per dentine site in the spectral range of 3500 to 200 cm^-1 and a resolution of 4 cm^-1. Background-corrected, normalized, and decomposed spectra were subjected to principal component analysis using MATLAB 2010 (The MathWorks, Natick, MA, USA). To assess age differences, prominent vibrational bands were observed and statistically analyzed, while sex differentiation employed the T-test on acquired data, exploring vibrational bands with significant intensity differences.

Results: The obtained results revealed a segmentation of spectra in the male sample group based on the age of teeth at extraction, with an accuracy of age estimation at 7.0048 years. A similar segmentation was observed in the female sample group, with an accuracy of 9.3863 years.

Conclusion: The recorded spectra were organized into datasets and analyzed with principal component analysis, demonstrating the feasibility of sex determination and age estimation using Raman spectra of teeth. Differences in classification accuracy between sexes may be attributed to hormonally-mediated differences in the biochemical composition of dentine between males and females. The findings of this study can provide valuable insights into methods for forensic and anthropological applications.

Objectives: The aim of this systematic review and meta-analysis is to assess the association between the MIH presence as well as the severity and OHRQoL in children.

Material and methods: Relevant studies were identified in PubMed, Embase, Cochrane and Google Scholar. Studies involving MIH and OHRQoL in children were included. A methodological quality assessment of included studies was performed using the Newcastle-Ottawa Scale (NOS) and its adapted version for cross-sectional studies. Random effects models were used to estimate summary effect measures for the association between MIH presence (presence vs. absence) as well as severity (moderate/severe MIH vs. no MIH) and OHRQoL using generic inverse variance meta-analyses. Tests for heterogeneity, publication bias and sensitivity of results were also performed.

Results: Out of 1696 identified publications 11 studies reporting on 5,017 children were included in the meta-analysis assessing the impact of MIH presence. There was no statistically significant association between the presence of MIH and lower OHRQoL in affected children (OR = 1.72, 95% CI = 0.99-2.98). Concerning MIH severity and its impact on OHRQoL, a sum of 6 studies were included in the meta-analysis involving a total of 2,595 children. There was a significant association between moderate/severe MIH and lower OHRQoL in affected children (OR = 3.43, 95% CI = 1.69-6.98).

Conclusion: Moderate/Severe MIH has a significant and clinically relevant negative impact on OHRQoL, and it should therefore be addressed adequately. Future research should also consider the impact of a uniform MIH diagnosis and precise severity criteria.

Objectives: To examine the effects of different whitening agents on the color and translucency of different resin composites, in vitro.

Material and methods: A total of 315 specimens (10.0 ×2.0 mm) were fabricated from two microhybrid (G-aenial anterior [G-Ant]) and (G-aenial posterior [G-Post]) and a nano hybrid (G-aenial A'CHORD [ G-ACH]) resin composites and each group was randomly distributed into seven experimental groups (n=15) as follows; 1- control (C); 2- in-office whitening agent (IOW); 3- at-home whitening agent (AHW); 4- prefilled tray (PT); 5- whitening pen (WP); 6- whitening toothpaste (WT) and 7- whitening mouthwash (WMW). The specimens were subjected to staining except control group before application of the different whitening procedures. The color of specimens was measured after 24 h (T₀), after staining (T₁) and after whitening (T₂). Color change [CIEDE2000 (ΔE₀₀)], translucency parameter (TP) values and changes in whiteness index (WI_D) were calculated. Data were analyzed statistically (p<0.05).

Results: No significant 𝑊I_D differences were detected among the tested resin composites at T₀ and T₁ (p>0.05), whereas a significant difference was observed at T₂ (p<0.005). AHW and IOW produced higher color change than PT, WP, WT and WMR. Significant TP changes were found after the application of IOW and AHW in G-Ant.

Conclusion: The effect of whitening products on the whitening index, color and translucency of resin composites are material and substrate dependent.

The presence of supernumerary tooth (SNT) in the nasal cavity is a rare condition with limited literature data. We report two cases with a history of nasal obstruction and difficulty breathing. In both cases, clinical and radiological examination confirmed intranasal SNT. Extractions were executed in general anesthesia using Rochester-Pean instruments transnasally. In addition, a literature review of intranasal SNT was performed. The database search retrieved a total number of 50 cases in time period from 1970 to 2020. Mean age of patients was 22.5 years. Most common symptoms were unilateral obstruction of breathing and headache. Surgical extraction of intranasal SNT is recommended to eliminate the symptoms.

Objectives: To optimize the therapeutic usefulness of aligners, it is crucial to understand how their mechanical properties alter with time.

Materials and methods: Specimens from four different brands, including Duran+, CA® Pro, Zendura A, and Zendura FLX, were produced for material testing of thermoplastic orthodontic aligners (TOA) using dimensions measuring 4mm x 10mm. Each brand's 24 samples were split into three groups as follows: G1 being thermoformed, G2 being thermoformed and underwent 500 thermocycles (simulating 7 days), and G3 being thermoformed and underwent 1000 thermocycles (simulating 14 days). Surface roughness, modulus of elasticity in bending, and spectrophotometry were used to assess the effect of aging on TOAs.

Results: After 1000 thermocycles, Duran+ had the highest modulus of elasticity and differed statistically from all other groups. The intragroup comparison showed that only Duran+'s elastic modulus significantly changed after 1000 thermocycles in comparison with the control group. Surface roughness values (Ra), did not statistically differ among brands or thermocycling group measures. The change in chemical properties was not significant in any brand.

Conclusion: One-layer PETG (Duran+) failed to demonstrate stability after in vitro aging, thus suggesting that clinicians should be aware of the change in mechanical properties when using one-layer PETG (Duran +) in a 2 weeks regime.

Objective: The study has evaluated the accuracy (trueness and precision) of seven extraoral scanners when scanning two different types of jaws: simplified jaw with sharp edges and abutments and realistic jaw with natural teeth. The accuracies of extraoral scanners were compared, and their compliance with the required clinical accuracy levels was discussed.

Material and methods: Ten scans were made with each scanner for both models. The comparison of the selected dental scanners relied on reference scans made for both models. Trueness, precision, and the distribution and value of laboratory scan points' deviations were assessed for each scanner across the models.

Results: The trueness for the model of the simplified jaw with abutments ranged from 16.15 to 49.78 μm. The measured precision values for the same model ranged from 4.33 to 29.49 μm. For the model of the realistic jaw with natural teeth, the trueness results ranged from 11.32 to 24.55 μm, while the obtained precision values were between 2.29 and 18.06 μm.

Conclusion: The revealed dissimilarities in the accuracies of scanners and their ranking when scanning different models lead to the conclusion that model selection is critical for the research design. All the scanners met the clinical accuracy requirements and are suitable for use in laboratories for scanning jaws with abutments and jaws with natural teeth. However, the accuracy values reported by the manufacturers of scanners are better than those obtained in this study. Furthermore, the results suggested that blue light scanners outperform white light and laser scanners.

Objectives: The objective of this study was to investigate the efficacy of tooth whitening and the effects on satisfaction with whitening treatment and esthetic self-perception of over-the-counter tooth whitening products.

Materials and methods: Fifty-six participants were randomly allocated to three groups based on the whitening product they used (toothpaste, pencil, or a combination of both). In this prospective study, alterations in tooth color were assessed using a spectrophotometer at three distinct time intervals (initial measurement, seven days, and 14 days after commencing the use of the whitening product). Simultaneously, the respondents were given the PIDAQ questionnaire to complete. Patient satisfaction with treatment characteristics (5-point Likert scale), and perception of side effects were assessed at the end of the study.

Results: Participants who used the whitening pen either alone or in combination with whitening toothpaste showed significant improvements in tooth color and whiteness index at seven and 14 days compared to those who used whitening toothpaste alone (p≤0.001). No significant differences were found between products in overall satisfaction with treatment, perception of final tooth color, and treatment comfort. Furthermore, with the exception of the psychological influence factor after 14 days (p≤0.001), there were no significant differences in the PIDAQ questionnaire scores between the whitening products at the different time points. However, many respondents (16.6%) reported oral mucosal sensitivity and a higher percentage (27.8%) reported tooth sensitivity during whitening pen application.

Conclusion: The combination of whitening toothpaste and whitening pen, as well as the whitening pen alone, showed effective objective color change results, but home whitening procedures did not significantly affect participants' self-perceived satisfaction or psychosocial outcomes depending on the product used.

Objectives: This study aimed to assess the color stability, surface roughness, and flexural properties of the injection-molded thermoplastic polyamide Vertex ThermoSens denture base resin following a 3-minute immersion in Polident 3-minute denture cleanser.

Methods: Sixty specimens (Vertex ThermoSens) were processed and divided into two main groups (n = 30) based on the type of test. Group 1 was further subdivided into two subgroups (n = 15): the control group immersed in distilled water (G1DW) and the test group immersed in Polident cleanser solution (G1PD). Group 2 was divided into three subgroups: a non-immersed group (G2None), a group immersed in distilled water (G2DW), and a group immersed in Polident cleanser solution (G2PD). Color change (∆E) and surface roughness measurements were conducted for group 1, and flexural modulus (E) test was performed for group 2. The CIE Lab* formula was utilized to calculate ∆E. An optical 3D surface analyzer and a three-point bending test were employed for surface roughness and E assessments, respectively. Data were subjected to statistical analysis using a paired-sample t-test for differences within each group before and after immersion. Furthermore, independent-sample t-tests and one-way ANOVA were conducted to analyze differences between groups. A significance level of P < 0.05 was considered.

Results: The results revealed a slight, statistically insignificant (P > 0.05) ∆E in all color components (L*, a*, b*) after immersion in distilled water. However, after immersion in the denture cleanser, only the L* component exhibited a statistically significant ∆E (P = 0.002), which was slight in magnitude. Additionally, a significant difference was found in the ∆E between G1DW and G1PD, with G1PD showing a higher change (P = 0.007). A significant increase in surface roughness after immersion was observed in G1PD (P = 0.017), with a notable difference between G1DW and G1PD. However, the E remained unaffected (P = 0.537).

Conclusion: Denture cleansers have the potential to modify the properties of thermoplastic polyamide resin. Further research is needed to explore the clinical implications of these observed changes on denture performance.

Background: Dental phenotype shows variation in the form of various metric and non-metric traits, primarily due to gene-environment interplay. It gives an insight into the evolutionary trends, ancestry, and food habits. Recently, it has been explored for genetic affinity with several growth anomalies and development of craniofacial skeleton which is also responsible for dental and skeletal malocclusions.

Objectives: the current study aims to investigate the non-metric dental crown traits (NDCTs) using Arizona State University Dental Anthropology system (ASUDAS) in different types of malocclusions in Delhi, National Capital Region (NCR) population.

Materials and methods: The study design was observational and retrospective. The total sample comprised of 240 pairs of dental casts divided into four equal groups of 60 subjects each (30 male and 30 female), based on malocclusion. The four groups of malocclusions were: Angle's Class I, Class II division 1, Class II division 2, Class III. The investigator was blinded for patient ID and sex before recording the data. The data for cast were recorded by three observers independently in a modified malocclusion- non-metric dental crown traits (M-NDCT) anthropological variants chart and statistically analyzed for association with different malocclusions and sex.

Results: Significant differences were found in the expression of several NDCTs (both in presence and scoring) in different malocclusions. Class I malocclusion showed a predominantly winging, shoveling -upper central and lateral incisor, protostylid, hypoconulid absence in lower second molar, and cusp number. Class II malocclusion showed a double shoveling, interrupted groove, tuberculum dentale, canine mesial ridge, premolar accessory cusp, Carabelli's trait, lingual cusp variation, and seventh cusp in the lower left first molar. Class III malocclusion showed the absence of hypocone in upper second molar, deflecting wrinkle, distal trigonid crest, and Y groove in left lower second molar (26.7%). Besides, sexual dimorphism was seen in shoveling -upper central and lateral incisor, canine mesial ridge, Carabelli's trait, 3-cusp in upper second molar, and cusp number.

Conclusions: Significant association was found between non-metric dental traits and malocclusions (Class I, Class division 1, Class II division 2, and Class III). Significant sex-linked differences were also found. Further studies can be performed at multicenter pan-India level with a standard robust protocol and a large sample.