Pub Date : 2023-06-20DOI: 10.5552/drvind.2023.0047
G. Nemli, U. Aras, Hülya Kalaycoglu, Suleyman Kustas
In this study, the effect of using olive stone residues (OSR) on some properties of particleboard was investigated. For this purpose, particle boards were manufactured from particles of white poplar (Populus Alba L.), which were partially substituted with OSR particles in amounts of 10 %, 20 % and 30 %. In addition, boards containing 30 % OSR, which had previously been chemically modified with NaOH solution, were produced. Phenol formaldehyde adhesive was used in the production of the boards. Chemical properties of wood and OSR particles (pH, alcohol benzene solubility, amount of ash), physico-mechanical properties (density, moisture content thickness swelling, modulus of rupture, modulus of elasticity and internal bond strength) and formaldehyde emission values of boards were determined. Water absorption and thickness swelling values were generally decreased with the increase in the use of OSR. When the effect of OSR usage on bending strength, modulus of elasticity, and perpendicular tensile strength values were examined, a decrease in the values was observed except for the 10 % OSR usage ratio. As a result of the application of alkali pretreatment, an increase in thickness swelling values was observed, while the values of mechanical properties increased. Scanning electron microscopy (SEM) analysis results showed more spaces between particles with an increasing OSR usage ratio. Formaldehyde emission values decreased with the increasing amount of OSR. Formaldehyde emission values increased slightly with the application of alkaline pretreatment. Based on the findings of this study, we can conclude that OSR can be used at particularly low ratio in particleboard production.
研究了橄榄石废渣对刨花板某些性能的影响。为此，颗粒板由白杨（Populus Alba L.）颗粒制成，其被10%、20%和30%的OSR颗粒部分取代。此外，还生产了含有30%OSR的板材，这些板材以前曾用NaOH溶液进行过化学改性。酚醛胶粘剂被用于板材的生产。测定了木材和OSR颗粒的化学性能（pH、醇苯溶解度、灰分）、物理力学性能（密度、含水量、厚度膨胀、断裂模量、弹性模量和内部粘结强度）以及板材的甲醛释放值。吸水率和厚度膨胀值通常随着OSR使用的增加而降低。当检查OSR使用对弯曲强度、弹性模量和垂直拉伸强度值的影响时，除了10%的OSR使用率之外，观察到这些值的降低。由于应用了碱预处理，观察到厚度溶胀值增加，而机械性能值增加。扫描电子显微镜（SEM）分析结果显示，随着OSR使用率的增加，颗粒之间的空间越来越大。甲醛释放值随着OSR用量的增加而降低。甲醛释放值随着碱性预处理的应用略有增加。基于这项研究的结果，我们可以得出结论，OSR可以在刨花板生产中以特别低的比例使用。
{"title":"Potential Use of Olive Stone Residues in Particleboard Production","authors":"G. Nemli, U. Aras, Hülya Kalaycoglu, Suleyman Kustas","doi":"10.5552/drvind.2023.0047","DOIUrl":"https://doi.org/10.5552/drvind.2023.0047","url":null,"abstract":"In this study, the effect of using olive stone residues (OSR) on some properties of particleboard was investigated. For this purpose, particle boards were manufactured from particles of white poplar (Populus Alba L.), which were partially substituted with OSR particles in amounts of 10 %, 20 % and 30 %. In addition, boards containing 30 % OSR, which had previously been chemically modified with NaOH solution, were produced. Phenol formaldehyde adhesive was used in the production of the boards. Chemical properties of wood and OSR particles (pH, alcohol benzene solubility, amount of ash), physico-mechanical properties (density, moisture content thickness swelling, modulus of rupture, modulus of elasticity and internal bond strength) and formaldehyde emission values of boards were determined. Water absorption and thickness swelling values were generally decreased with the increase in the use of OSR. When the effect of OSR usage on bending strength, modulus of elasticity, and perpendicular tensile strength values were examined, a decrease in the values was observed except for the 10 % OSR usage ratio. As a result of the application of alkali pretreatment, an increase in thickness swelling values was observed, while the values of mechanical properties increased. Scanning electron microscopy (SEM) analysis results showed more spaces between particles with an increasing OSR usage ratio. Formaldehyde emission values decreased with the increasing amount of OSR. Formaldehyde emission values increased slightly with the application of alkaline pretreatment. Based on the findings of this study, we can conclude that OSR can be used at particularly low ratio in particleboard production.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-06-20","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43806357","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-20DOI: 10.5552/drvind.2023.0089
Z. Vlaović, Vid Palalić, D. Domljan
The paper provides a limited overview of existing pressure sensors based on composite technology from carbonized biomass and synthetic materials which could be implemented in seating furniture. Carbon-based pressure sensors have proven to be good for pressure measurement that works on the principle of the piezoresistive effect. Research on materials based on carbonized components of biological origin encourages the development of composite sensors made of different materials, which have different negative and positive properties. Despite the great potential, such sensors are still not sufficiently researched and there is a lot of space for their improvement. Today’s rapid development of technologies and frequent work at the computer leads to excessive sitting while working, which is a big problem for human health. Chairs with sensors could be increasingly used in the future, and in combination with the Internet of Things could be used to monitor the sitting habits and health of users. Sensors implemented in seating furniture are one way of monitoring sitting habits, warning users of inappropriate body positions when sitting, and mitigating the negative consequences of long-term improper sitting. The paper analyses research that includes the production and application of sensors made of carbonized bio-materials, which could be used in seating furniture with the aim of monitoring the way of sitting based on the principle of pressure detection. So far, the results have not provided the requested answers. However, they provided an overview of technologies that, with additional research, likely have the potential to be incorporated into seating furniture.
{"title":"Research of Carbon Biosensors for Application in Seating Furniture","authors":"Z. Vlaović, Vid Palalić, D. Domljan","doi":"10.5552/drvind.2023.0089","DOIUrl":"https://doi.org/10.5552/drvind.2023.0089","url":null,"abstract":"The paper provides a limited overview of existing pressure sensors based on composite technology from carbonized biomass and synthetic materials which could be implemented in seating furniture. Carbon-based pressure sensors have proven to be good for pressure measurement that works on the principle of the piezoresistive effect. Research on materials based on carbonized components of biological origin encourages the development of composite sensors made of different materials, which have different negative and positive properties. Despite the great potential, such sensors are still not sufficiently researched and there is a lot of space for their improvement. Today’s rapid development of technologies and frequent work at the computer leads to excessive sitting while working, which is a big problem for human health. Chairs with sensors could be increasingly used in the future, and in combination with the Internet of Things could be used to monitor the sitting habits and health of users. Sensors implemented in seating furniture are one way of monitoring sitting habits, warning users of inappropriate body positions when sitting, and mitigating the negative consequences of long-term improper sitting. The paper analyses research that includes the production and application of sensors made of carbonized bio-materials, which could be used in seating furniture with the aim of monitoring the way of sitting based on the principle of pressure detection. So far, the results have not provided the requested answers. However, they provided an overview of technologies that, with additional research, likely have the potential to be incorporated into seating furniture.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-06-20","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44598985","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-20DOI: 10.5552/drvind.2023.0050
Osman Goktas, Yasar Tahsin Bozkaya, Mehmet Yeniocak
The main goal of the study is to produce eco-friendly furniture dyes by using bio-colorants and to determine the color stability of these dyes in outdoor conditions. In this regard, dye extracts obtained from red beet (Beta vulgaris), safflower (Carthamus tinctorius L.), and purple cabbage (Brassica oleracea), as a bio-colorant source, were applied to MDF test panels by mixing with water-based synthetic lacquer coatings. Also, three different synthetic dyes were applied to MDF test panels in order to compare the results with eco-friendly natural dyes. Natural dyes were mixed with metal and natural mordants such as iron sulfate, aluminum sulfate and vinegar. Lacquer coated test panels, coated with natural and synthetic dyes, were exposed to outdoor conditions for 50 days in Denizli/Turkey in order to assess the change in color. As a result, the maximum color stability occurred in the test panels lacquer coated with synthetic black dye, while the minimum color stability occurred in the test panels lacquer coated with synthetic light blue dye. It was determined that the thickness of the color coating layer applied to test panels increases color stability. It was also observed that the color stability performance of natural dyes is as good as that of synthetic dyes.
{"title":"Obojenje lakova za namještaj s biljnim bojilima i određivanje njihove otpornosti na vremenske utjecaje","authors":"Osman Goktas, Yasar Tahsin Bozkaya, Mehmet Yeniocak","doi":"10.5552/drvind.2023.0050","DOIUrl":"https://doi.org/10.5552/drvind.2023.0050","url":null,"abstract":"The main goal of the study is to produce eco-friendly furniture dyes by using bio-colorants and to determine the color stability of these dyes in outdoor conditions. In this regard, dye extracts obtained from red beet (Beta vulgaris), safflower (Carthamus tinctorius L.), and purple cabbage (Brassica oleracea), as a bio-colorant source, were applied to MDF test panels by mixing with water-based synthetic lacquer coatings. Also, three different synthetic dyes were applied to MDF test panels in order to compare the results with eco-friendly natural dyes. Natural dyes were mixed with metal and natural mordants such as iron sulfate, aluminum sulfate and vinegar. Lacquer coated test panels, coated with natural and synthetic dyes, were exposed to outdoor conditions for 50 days in Denizli/Turkey in order to assess the change in color. As a result, the maximum color stability occurred in the test panels lacquer coated with synthetic black dye, while the minimum color stability occurred in the test panels lacquer coated with synthetic light blue dye. It was determined that the thickness of the color coating layer applied to test panels increases color stability. It was also observed that the color stability performance of natural dyes is as good as that of synthetic dyes.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-06-20","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42775156","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-03-25DOI: 10.5552/drvind.2023.0053
Alma Žiga, J. Kačmarčik
In this paper, the elastic behaviour in bending of three-layer plywood cantilever beams is analysed. Deflections of straight and half-circle cantilevers, loaded with a force at free end is determined experimentally and calculated using analytical and finite element method approach. The analytical calculation of deflection for the strait cantilever is obtained using a transformed cross section. The deflection of half-circle cantilever is determined by the classical laminated plate theory and Castigliano’s theorem. Loads and cantilever dimensions are varied in the study using the design of experiment. The deflection regression models for straight and semicircular plywood cantilevers are obtained from the experimental results. Analytically and numerically determined deflections of strait and half-circle cantilevers show very good agreement. Experimentally recorded deflections are approximately 30 % higher than analytical values. Stiffness properties and deflection values are influenced by direction of fibres in the outer layers of a three-layer plywood beam.
{"title":"Plywood Cantilever Deflection","authors":"Alma Žiga, J. Kačmarčik","doi":"10.5552/drvind.2023.0053","DOIUrl":"https://doi.org/10.5552/drvind.2023.0053","url":null,"abstract":"In this paper, the elastic behaviour in bending of three-layer plywood cantilever beams is analysed. Deflections of straight and half-circle cantilevers, loaded with a force at free end is determined experimentally and calculated using analytical and finite element method approach. The analytical calculation of deflection for the strait cantilever is obtained using a transformed cross section. The deflection of half-circle cantilever is determined by the classical laminated plate theory and Castigliano’s theorem. Loads and cantilever dimensions are varied in the study using the design of experiment. The deflection regression models for straight and semicircular plywood cantilevers are obtained from the experimental results. Analytically and numerically determined deflections of strait and half-circle cantilevers show very good agreement. Experimentally recorded deflections are approximately 30 % higher than analytical values. Stiffness properties and deflection values are influenced by direction of fibres in the outer layers of a three-layer plywood beam.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"45118323","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-03-25DOI: 10.5552/drvind.2023.0006
Günay Özbay, Musa Atar, Ayhan Ozcifci
In this study, phenol-formaldehyde (PF) resin has been modified with titanium dioxide nanoparticles (nano-TiO2) at a varying ratio from 0.05 wt.% to 1.5 wt.% to enhance the thermal properties and combustion performance of the resins. The effect of the nano-TiO2 modification on the properties (chemical or thermal) of the resins was determined by Fourier to transform infrared (FT-IR) and thermal analysis (TGA) techniques. In addition, the combustion performance of laminated veneer lumber (LVL) samples bonded with the PF resin modified with nano-TiO2 was tested. The result of the FT-IR analysis indicated that the modified PF resins had match peaks to the reference PF resin. These similarities of the peaks supported that the modified PF resins were successfully synthesise with phenol, formaldehyde, and nano-TiO2. The PF resins modified by nano-TiO2 demonstrated better thermal stability than the reference resin. The nano-TiO2 modified PF resin exhibited a favourable influence on the combustion characteristics of LVL. In consequence, PF resin modified with nano-TiO2 could be used as a combustion retardant adhesive in the wood industry.
{"title":"Sinteza fenolne smole ojačane nanočesticama TiO2 i njezin utjecaj na gorivost lamelirane drvne građe (LVL)","authors":"Günay Özbay, Musa Atar, Ayhan Ozcifci","doi":"10.5552/drvind.2023.0006","DOIUrl":"https://doi.org/10.5552/drvind.2023.0006","url":null,"abstract":"In this study, phenol-formaldehyde (PF) resin has been modified with titanium dioxide nanoparticles (nano-TiO2) at a varying ratio from 0.05 wt.% to 1.5 wt.% to enhance the thermal properties and combustion performance of the resins. The effect of the nano-TiO2 modification on the properties (chemical or thermal) of the resins was determined by Fourier to transform infrared (FT-IR) and thermal analysis (TGA) techniques. In addition, the combustion performance of laminated veneer lumber (LVL) samples bonded with the PF resin modified with nano-TiO2 was tested. The result of the FT-IR analysis indicated that the modified PF resins had match peaks to the reference PF resin. These similarities of the peaks supported that the modified PF resins were successfully synthesise with phenol, formaldehyde, and nano-TiO2. The PF resins modified by nano-TiO2 demonstrated better thermal stability than the reference resin. The nano-TiO2 modified PF resin exhibited a favourable influence on the combustion characteristics of LVL. In consequence, PF resin modified with nano-TiO2 could be used as a combustion retardant adhesive in the wood industry.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43670841","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-03-25DOI: 10.5552/drvind.2023.0087
Ivica Župčić, Igor Đukić, Matija Jug, Mario Jurišić, Marin Hasan
The increasing use of modified wood justifies the intention to use it in joints made by rotary welding with dowels. Thermal modification, for example, increases the dimensional stability of wood by reducing its hygroscopicity and water absorption, but it is difficult to glue or to rotary weld due to the appearance of cracks. This can be avoided by changing the optimal welding parameters, which on the other hand directly affects the reduction of the pull-out force by more than 25 % depending on the type of the modified base. In the case of welding wooden dowels into wood modified with citric acid, the reduction in pull-out force is even greater. Due to the significant reduction, the use of this type of modification for wood welding is questionable. When citric acid modification is extended to the dowels, the dowel becomes a problem due to its lower tensile strength, which is even lower than the pull-out force of the welded dowel.
{"title":"Utjecaj različitih vrsta modifikacije na izvlačnu silu rotacijski zavarenih moždanika","authors":"Ivica Župčić, Igor Đukić, Matija Jug, Mario Jurišić, Marin Hasan","doi":"10.5552/drvind.2023.0087","DOIUrl":"https://doi.org/10.5552/drvind.2023.0087","url":null,"abstract":"The increasing use of modified wood justifies the intention to use it in joints made by rotary welding with dowels. Thermal modification, for example, increases the dimensional stability of wood by reducing its hygroscopicity and water absorption, but it is difficult to glue or to rotary weld due to the appearance of cracks. This can be avoided by changing the optimal welding parameters, which on the other hand directly affects the reduction of the pull-out force by more than 25 % depending on the type of the modified base. In the case of welding wooden dowels into wood modified with citric acid, the reduction in pull-out force is even greater. Due to the significant reduction, the use of this type of modification for wood welding is questionable. When citric acid modification is extended to the dowels, the dowel becomes a problem due to its lower tensile strength, which is even lower than the pull-out force of the welded dowel.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":"1 1","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42106244","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-03-25DOI: 10.5552/drvind.2023.0020
Mislav Mikšik, Stjepan Pervan, Miljenko Klarić, Anita Čavlović, Nikola Španić, Silvana Prekrat
The effect of temperature and moisture on the behaviour of solid wood is a well-known fact that directly affects wood creep as well. Wood creep includes three types of behaviour, such as viscoelastic creep, mechano-sorptive creep, and pseudo-creep and recovery. All these types can occur simultaneously, and it is sometimes complicated for researchers to isolate or distinct one from another. This paper presents a review of literature on wood rheology and creep properties, as well as factors that influence them, mainly time, temperature, and moisture content. The study of the viscoelasticity and wood creep is very important for gaining knowledge to be applied in solid wood bending.
{"title":"Čimbenici koji utječu na proces savijanja cjelovitog drva","authors":"Mislav Mikšik, Stjepan Pervan, Miljenko Klarić, Anita Čavlović, Nikola Španić, Silvana Prekrat","doi":"10.5552/drvind.2023.0020","DOIUrl":"https://doi.org/10.5552/drvind.2023.0020","url":null,"abstract":"The effect of temperature and moisture on the behaviour of solid wood is a well-known fact that directly affects wood creep as well. Wood creep includes three types of behaviour, such as viscoelastic creep, mechano-sorptive creep, and pseudo-creep and recovery. All these types can occur simultaneously, and it is sometimes complicated for researchers to isolate or distinct one from another. This paper presents a review of literature on wood rheology and creep properties, as well as factors that influence them, mainly time, temperature, and moisture content. The study of the viscoelasticity and wood creep is very important for gaining knowledge to be applied in solid wood bending.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43655942","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-03-25DOI: 10.5552/drvind.2023.0014
Suleyman Kustas, S. K. Gülsoy
In this study, effects of KBH4 (PB), NaBH4 (SB), Etibor-48 (E48), Etidot-67 (E67), and colemanite (Col) on kraft pulp and paper properties of Scots pine (Pinus sylvestris L.) wood were evaluated. The control and boron compound-added kraft pulps were obtained under constant cooking conditions. The boron compounds were used as digester additives in different ratios (2 % and 4 %). The addition of boron compounds to kraft cooking liquor resulted in increases screened and total yield of pulps. The highest screened yield (52.05 %) and total yield (55.09 %) were obtained from PB-4 pulp. The lowest reject ratio (0.61 %) and kappa number (34.60) were determined from PB-2 pulp. Furthermore, the highest tensile properties of handsheets were obtained from E67-4 pulp. Also, E48-4 pulp had the highest burst index and tear index values. E48, E67, and Col are cheaper than PB and SB. From these boron compounds, pulps with relatively low pulp yield but stronger can be obtained.
{"title":"Boron Compounds-Added Kraft Pulping from Scots Pine","authors":"Suleyman Kustas, S. K. Gülsoy","doi":"10.5552/drvind.2023.0014","DOIUrl":"https://doi.org/10.5552/drvind.2023.0014","url":null,"abstract":"In this study, effects of KBH4 (PB), NaBH4 (SB), Etibor-48 (E48), Etidot-67 (E67), and colemanite (Col) on kraft pulp and paper properties of Scots pine (Pinus sylvestris L.) wood were evaluated. The control and boron compound-added kraft pulps were obtained under constant cooking conditions. The boron compounds were used as digester additives in different ratios (2 % and 4 %). The addition of boron compounds to kraft cooking liquor resulted in increases screened and total yield of pulps. The highest screened yield (52.05 %) and total yield (55.09 %) were obtained from PB-4 pulp. The lowest reject ratio (0.61 %) and kappa number (34.60) were determined from PB-2 pulp. Furthermore, the highest tensile properties of handsheets were obtained from E67-4 pulp. Also, E48-4 pulp had the highest burst index and tear index values. E48, E67, and Col are cheaper than PB and SB. From these boron compounds, pulps with relatively low pulp yield but stronger can be obtained.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42888277","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-03-25DOI: 10.5552/drvind.2023.0004
This paper investigated the bending moment of chair base joints. The ultimate bending moments (maximum moment), calculated on the base of the measured maximum applied loads (maximum force), were compared for the front leg and rear leg joints of a chair base. The joints had different angles between the stretcher and the leg (joint angle) as well different tenon lengths (30 mm and 32 mm). The results of the tests indicated that for different test specimen configurations but the same tenon-and-mortise geometry, the maximum force of joints with a smaller value of joint angle (front leg joints) was higher than the force values of joints with a larger angle (rear leg joints) for all tenon lengths. However, the results showed less difference among the calculated bending moments of the analysed sets of joints. A significant difference was not revealed between the bending moments of joints with a smaller value of joint angle and the bending moments of joints with a larger angle for all tenon lengths. A significant difference between the bending moments for the tenon length of 30 mm and tenon length of 32 mm was determined for rear leg joints but not for front leg joints. The presented approach of joint strength analysis through the testing of specimens with different shapes and dimensions are applicable to research and practice.
{"title":"Bending Moment of Mortise-and-Tenon Joints in a Crossed Chair Base","authors":"","doi":"10.5552/drvind.2023.0004","DOIUrl":"https://doi.org/10.5552/drvind.2023.0004","url":null,"abstract":"This paper investigated the bending moment of chair base joints. The ultimate bending moments (maximum moment), calculated on the base of the measured maximum applied loads (maximum force), were compared for the front leg and rear leg joints of a chair base. The joints had different angles between the stretcher and the leg (joint angle) as well different tenon lengths (30 mm and 32 mm). The results of the tests indicated that for different test specimen configurations but the same tenon-and-mortise geometry, the maximum force of joints with a smaller value of joint angle (front leg joints) was higher than the force values of joints with a larger angle (rear leg joints) for all tenon lengths. However, the results showed less difference among the calculated bending moments of the analysed sets of joints. A significant difference was not revealed between the bending moments of joints with a smaller value of joint angle and the bending moments of joints with a larger angle for all tenon lengths. A significant difference between the bending moments for the tenon length of 30 mm and tenon length of 32 mm was determined for rear leg joints but not for front leg joints. The presented approach of joint strength analysis through the testing of specimens with different shapes and dimensions are applicable to research and practice.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"45822053","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Dipteryx panamensis and Hieronyma alchorneoides are two species of high specific gravity used in reforestation programs in Costa Rica, but they lack products with structural value for commercialization. In order to introduce the wood of these two species in the market, the objective was established to study the behavior of solid timber beams and glued laminated timber beams of two cross sections (2 cm × 10 cm and 2 cm × 15 cm) and establish the design values in bending test. The results showed that the bending design values (fb) ranged from 2 to 26 MPa in glued laminated timber beams, while in solid timber beams, fb ranged from 6 to 15 MPa. In the shear design values (fv), the variation was from 0.29 to 0.67 MPa in glue laminated timber beams and from 1.80 to 2.58 MPa in solid timber beams. It was also found that the D. panamensis beams showed higher values than H. alchornoides beams. Finally, it was established that glued laminated timber beams showed better performance in bending parameters and higher design values, resulting in wider span values, than solid timber beams when used in floor and roof construction.
{"title":"Strukturne i projektirane vrijednosti lameliranih greda i greda od cjelovitog drva Dipteryx panamensis i Hieronyma alchorneoides s brzorastućih plantaža","authors":"Róger Moya, Carolina Tenorio, Angel Navarro-Mora, Freddy Munoz","doi":"10.5552/drvind.2023.0007","DOIUrl":"https://doi.org/10.5552/drvind.2023.0007","url":null,"abstract":"Dipteryx panamensis and Hieronyma alchorneoides are two species of high specific gravity used in reforestation programs in Costa Rica, but they lack products with structural value for commercialization. In order to introduce the wood of these two species in the market, the objective was established to study the behavior of solid timber beams and glued laminated timber beams of two cross sections (2 cm × 10 cm and 2 cm × 15 cm) and establish the design values in bending test. The results showed that the bending design values (fb) ranged from 2 to 26 MPa in glued laminated timber beams, while in solid timber beams, fb ranged from 6 to 15 MPa. In the shear design values (fv), the variation was from 0.29 to 0.67 MPa in glue laminated timber beams and from 1.80 to 2.58 MPa in solid timber beams. It was also found that the D. panamensis beams showed higher values than H. alchornoides beams. Finally, it was established that glued laminated timber beams showed better performance in bending parameters and higher design values, resulting in wider span values, than solid timber beams when used in floor and roof construction.","PeriodicalId":11427,"journal":{"name":"Drvna Industrija","volume":" ","pages":""},"PeriodicalIF":1.1,"publicationDate":"2023-03-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"45076329","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：