Journal of Analytical Methods in Chemistry最新文献

Objective: Cannabinoid extraction from Cannabis sativa L. (hemp) for nonmedical purposes has become popular in the United States. Concerns, however, have been raised regarding the accuracy of the labels for cannabinoid levels in the commercial products.

Methods: In this study, we developed rapid, sensitive, selective, accurate, and validated liquid chromatography-tandem mass spectrometry for the quantification of cannabinoids. The methods are for determining 11 cannabinoids in cannabis (hemp) extracted in oil form, and we investigated the accuracy of the labeling and thermal stability regarding the cannabinoids on 17 oil cannabis samples.

Results: In the UPLC chromatogram, we see a good resolution and there is no matrix effect and the accuracy were 98.2% to 102.6%, and the precision was 0.52%-8.18%. The linearity of the calibration curves in methanol was with a regression r² ≥ 0.99. The lowest of detection (LOD) was 5-25 ng/mL, and the limit of quantification (LOQ) was 10-50 ng/mL. The study showed that only 30% of the commercial samples were within the acceptable range of +/-10% compared to the labeled ingredient concentrations. The thermal stability test profile showed a change in the concentration of cannabinoids in each sample at 37°C for one week, with an average loss of cannabinoids up to 15%.

Conclusion: The validated method proved to be selective, accurate, and precise, with acceptable linearity within the calibration range with no matrix effect. The stability profile data indicated that high temperatures could change the quality of commercial samples.

Iron-based organic frame material MIL-53 (Fe) was synthesized by the hydrothermal method with Cu²⁺ incorporated to obtain bimetallic composite MIL-53 (Fe, Cu). The structure and morphology of the material were characterized by SEM, XRD, BET, FTIR, XPS, and zeta potential. The adsorption performance of MIL-53 (Fe, Cu) on methyl orange was tested under a variety of conditions, including the effects of pH and material dosage, by the static adsorption test. The results show that under the condition of pH = 7, a temperature of 30°C, and an adsorbent dosage of 20 mg, the removal rate of MIL-53 (Fe, Cu) for methyl orange can reach more than 96% within 4 h, and the maximum adsorption capacity after fitting by the thermodynamic model can reach 294.43 mg/g, showing the excellent adsorption performance of MIL-53 (Fe, Cu) on methyl orange. In addition, by exploring the adsorption mechanism of MIL-53 (Fe, Cu) on methyl orange, it is found that the adsorption of MIL-53 (Fe, Cu) on methyl orange depends on chemical adsorption, as evidenced by combining Fe³⁺ and Cu²⁺ in the material with methyl orange molecules to form complexes to achieve adsorption. While the specific surface area of the material had no obvious effect on adsorption, the effects of pH, temperature, and concentration were explored. At a pH of 6.5, greater adsorption occurred at higher temperatures, as determined by thermodynamic model fitting, as well as with higher initial methyl orange molecule concentration.

Oprozomib, as a second-generation orally bioavailable protease inhibitor (PI), is undergoing clinical evaluation for the treatment of haematological malignancies. In relapsed refractory multiple myeloma (RRMM) patients, oprozomib has shown good efficacy as a single agent or combination therapy. In this experiment, our purpose was to validate a sensitive and rapid method for the determination of oprozomib concentration in rat plasma by ultraperformance liquid chromatography tandem mass spectrometry (UPLC-MS/MS). The samples were treated with acetonitrile as the precipitant and separated by gradient elution using a Waters Acquity UPLC BEH C18 column (2.1 mm × 50 mm, 1.7 μm). Using the selective reaction monitoring (SRM) method, the measurement was finished with the ion transitions of m/z 533.18 ⟶ 199.01 for oprozomib and m/z 493.03 ⟶ 112.03 for tepotinib (internal standard, IS), respectively. Meanwhile, acetonitrile and 0.1% formic acid aqueous solution were used as the mobile phase, and the flow rate was 0.3 mL/min. The lower limit of quantification (LLOQ) of the method was 1.0 ng/mL, and the linear relationship was good in the range of 1.0-100 ng/mL. In addition, the precision of four concentration levels was determined with the values of 3.1-7.3% and the accuracy was from -14.9% to 12.9%. Moreover, the recovery was determined to be from 85.1% to 96.1%, and the values of matrix effect were no more than 110.4%. The optimized UPLC-MS/MS method was also suitable for the pharmacokinetic study of rats after a single oral administration of 21 mg/kg oprozomib.

TiO₂ nanoparticles have emerged as a great photocatalyst to degrade organic contaminants in water; however, the nanoparticles dispersed in water could be difficult to be recovered and potentially become contaminant. Herbicide like 2,4-dichlorophenoxyacetic acid (2,4-D) used in agriculture usually ends up with a large fraction remaining in water and sediment, which may cause potential risk to human health and the ecosystem. This study proposes a greener method to utilize TiO₂ as photocatalyst to remove 2,4-D from water. Accordingly, TiO₂ nanoparticles (10-45 nm) were synthesized and grafted on lightweight fired clay to generate a TiO₂-based floating photocatalyst. Experimental testing revealed that 60.2% of 2,4-D (0.1 mM) can be decomposed in 250 min under UV light with TiO₂-grafted lightweight fired clay floating on water. Degradation fits well into the pseudo-first-order kinetic model. The floating photocatalysts can degrade approximately 50% 2,4-D in 250 min under sunlight and the degradation efficiency is stable for cycles. The results revealed that the fabrication of floating photocatalyst could be a promising and greener way to remove herbicide contaminants in water using TiO₂.

Rapid and nondestructive measurement of moisture content in crude palm oil is essential for promoting the shelf-stability and quality. In this research, micro NIR spectrometer coupled with a multivariate calibration model was used to collect and analyse fingerprinted information from palm oil samples at different moisture contents. Several preprocessing methods such as standard normal variant (SNV), multiplicative scatter correction (MSC), Savitzky-Golay first derivative (SGD1), Savitzky-Golay second derivative (SGD2) together with partial least square (PLS) regression techniques, full PLS, interval PLS (iPLS), synergy interval PLS (SiPLS), genetic algorithm PLS (GAPLS), and successive projection algorithm PLS (SPA-PLS) were comparatively employed to construct an optimum quantitative prediction model for moisture content in crude palm oil. The models were evaluated according to the coefficient of determination and root mean square error in calibration (Rc and RMSEC) and prediction (Rp and RMSEC) set, respectively. The model SGD1 + SiPLS was the optimal novel algorithm obtained among the others with the performance of Rc = 0.968 and RMSEC = 0.468 in the calibration set and Rp = 0.956 and RMSEP = 0.361 in the prediction set. The results showed that rapid and nondestructive determination of moisture content in palm oil is feasible and this would go a long way to facilitating quality control of crude palm oil.

Ivermectin is a macrocyclic lactone widely used in veterinary medicine for its broad-spectrum antiparasitic properties. It has been proven to be effective and safe. The purpose of this study was to develop a high-performance liquid chromatography method with a diode array detector for ivermectin screening in feed and water for animal consumption. Furthermore, the objective was to quantify ivermectin levels that were higher than 0.5 mg/kg in solid matrixes and 0.1 mg/kg in water. Doramectin was used as process standard. Samples were extracted using solid phase extraction with silica and C-18 columns. The method involved the use of high-performance liquid chromatography (HPLC) with a diode array detector (DAD). The results were interpreted using a calibration curve built with ivermectin standards at multiple concentrations (0.5, 1, 2, 5, and 12.5 mg/kg). Statistical evaluation of data was done using ANOVA. The data analysis showed that the linear regression was highly significant (P < 0.001), the intercept values were not significantly different from zero, and the correlation coefficient values (>0.999) indicated excellent linearity. Further tests demonstrated that this method is also useful when studying soil matrixes. The soil was dried and analyzed in the same way as feed; the same recoveries were realized on the spiked samples. The method is easy, inexpensive, precise, and repeatable; it requires very small amounts of sample.

Schisandrin B (Sch.B) shows antineoplastic activity in colorectal cancer, but the mechanism is still obscure. The intracellular spatial distribution may be helpful in elucidating the mechanism. To investigate the intracellular drug distribution of Sch.B in cancer cells, a simple, rapid, and sensitive ultra-highperformance liquid chromatography tandem mass spectrometry (UHPLC-MS/MS) method was established for the determination of Sch.B in colorectal cancer cells. Warfarin was utilized as an internal standard. The sample pretreatment was carried out with protein precipitation using methanol. The analyte was separated on an Atlantis T3-C₁₈ column (3 μm, 2.1∗100 mm) using gradient elution with a mobile phase comprised of methanol and 0.2% formic acid in water. The flow rate was 0.4 mL/min. The linear range of Sch.B was 20.0-1000.0 ng/mL with a correlation coefficient (R) more than 0.99. The matrix effect and recovery ranged from 88.01% to 94.59% and from 85.25% to 91.71%; the interday and intraday precision and accuracy, stability, specificity, carryover, matrix effect, and recovery all conformed to the requirements of pharmacopoeia. Cell viability and apoptosis assays demonstrated that Sch.B has an inhibitory effect in a dose-dependent way on HCT116 proliferation and achieved significant suppression at 75 μM (IC₅₀). It was found that in HCT116 cell, nucleus, and mitochondria, exposure levels of Sch.B peaked at 36 h and then decreased, and mitochondria possessed more Sch.B than nucleus. These results may help to elucidate the antitumor effect of Sch.B.

Simple, accurate, precise, and cost-effective chemometric techniques for the measurement of candesartan cilexetil and hydrochlorothiazide in synthetic mixtures were improved and validated. H-point standard addition, Q-absorption ratio, and correction absorbance spectrophotometric techniques were utilized for the simultaneous determination of both medicines in real pharmaceutical formulations. A new calibration approach was implemented based on chemical H-point standards. This approach was developed to resolve significantly overlapping spectra of two analytes and provide direct correction of both proportional and constant errors caused by the matrix of the sample. The first method of simultaneous determination of candesartan cilexetil and hydrochlorothiazide was carried out using the H-point standard addition method at wavelengths 239 and 283. For the ratio of the absorption at two selected wavelengths, one of which is the isoabsorptive point and the other being the maximum of one of the two components, the second method absorption ratio method was utilized. In distilled water, the isoabsorptive point of candesartan cilexetil and hydrochlorothiazide occurs at 258 nm. λ _max of hydrochlorothiazide is 273 nm, which is the second wavelength used. Lastly, the absorbance correction method was implemented. This approach is based on absorbance correction equations and uses distilled water as the solvent for the examination of both medicines. In NaOH/EtOH solvent, the absorbance maxima of candesartan cilexetil and hydrochlorothiazide are 250 nm and 340 nm, respectively. For both wavelengths, candesartan cilexetil and hydrochlorothiazide exhibited linearity over a concentration range of 1-46 μg/ml and 1-44 μg/ml, respectively, for H-point standard addition. The Q-absorption ratio approach provides linearity over the concentration ranges of 1-46 μg/ml at 273 nm for candesartan cilexetil and 1-29 μg/ml for hydrochlorothiazide, 1-46 μg/ml at 258 nm for candesartan cilexetil, and 1-44 μg/ml for hydrochlorothiazide. For hydrochlorothiazide, the linearity for the correction absorbance method was obtained throughout a concentration range of 1-46 μg/ml at wavelengths 250 and 340 nm and 1-44 μg/ml at wavelength 250 nm. The results of the analysis have been statistically and empirically supported by recovery studies. All methods yielded recoveries in the range of 96 -102% for both medications. The LOD ranged from 0.46 -0.94 μg/mL for hydrochlorothiazide and from 1.26 -2.40 μg/mL for candesartan cilexetil. The approaches were then used to quantify candesartan cilexetil and hydrochlorothiazide in pharmaceutical tablets.

In this study, a magnetic metal-organic framework (MOF) was synthesized based on magnetic Fe₃O₄, Cu(II), and benzene-1,3,5-tricarboxylic acid (Cu-BTC) as a sorbent for solid phase extraction (SPE) of trace amounts of Pb(II) in water and lettuce samples. Pb(II) ion was adsorbed on the magnetic MOF and easily separated by a magnet; therefore, no filtration or centrifugation was necessary. The analyte ions were eluted by HCl 0.5 mol·L^-1 and analyzed via graphite furnace atomic absorption spectroscopy. The prepared sorbent was characterized by scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and Fourier transform-infrared (FT-IR) spectroscopy. Under optimal experimental conditions, the method had a linear range of 0.1-50 μg·L^-1. The limits of detection and quantitation for lead were found to be 0.026 and 0.08 μg·L^-1, respectively. The results showed that the prepared sorbent has high selectivity for Pb²⁺ even in the presence of other interfering metal ions.

Cistanche tubulosa (Schenk) R. Wight is a valuable herbal medicine in China. The study aimed to explore the potential mechanisms of C. tubulosa on antioxidant activity using spectrum-effect relationship and network pharmacology and the possibilities of utilizing herbal dregs. In this work, different extracts of C. tubulosa, including herbal materials, water extracts, and herbal residues, were evaluated using high-performance liquid chromatography (HPLC) technology. In addition, the antioxidant activities were estimated in vitro, including 2, 2-diphenyl-1-picrylhydrazyl; superoxide anion; and hydroxyl radical scavenging assays. The spectrum-effect relationships between the HPLC fingerprints and the biological capabilities were analyzed via partial least squares regression, bivariate correlation analysis, and redundancy analysis. Furthermore, network pharmacology was used to predict potential mechanisms of C. tubulosa in the treatment of antioxidant-related diseases. According to the results, eleven common peaks were shared by different extracts. Geniposidic acid, echinacoside, verbascoside, tubuloside A, and isoacteoside were quantified and compared among different forms of C. tubulosa. The spectrum-effect relationship study indicated that peak A ₆ might be the most decisive component among the three forms. Based on network pharmacology, there were 159 target genes shared by active components and antioxidant-related diseases. Targets related to antioxidant activity and relevant pathways were discussed. Our results provide a theoretical basis for recycling the herbal residues and the potential mechanisms of C. tubulosa in the treatment of antioxidant-related diseases.