Pub Date : 2024-06-18DOI: 10.1186/s10086-024-02143-3
Ryo Takase, Atsuko Ishikawa, Daisuke Kamikawa
Despite the increasing outdoor use of fire-retardant-treated wood, methods for predicting its service life remain poorly established. With the aim of establishing a method to predict chemical losses from fire-retardant-treated (FRT) wood caused by humid atmospheres and rain outdoors, this study examined the preferable conditions for artificial-weathering tests and demonstrated the acceleration coefficients in these tests (i.e., the ratio of equivalent time to reach the same retention of chemicals in artificial weathering and outdoors) based on the EN927-6 standard. To determine the moisture absorption and desorption levels of FRT exposed to outdoor conditions, an outdoor exposure experiment was conducted. The moisture content was higher in the FRT wood than in untreated wood, regardless of the type of coating, and ranged between 11% (in March) and 50% (in September) of the untreated wood’s weight. EN927-6 artificial weathering tests were performed on two groups of specimens with initial moisture contents of 0% and 25%. Retention rates of fire-retardant chemicals after a 2520-h test were compared with those retrieved from 4-year outdoor exposure reported elsewhere. Comparison of these two experiments demonstrated that the acceleration coefficients were 4.1–11.3 in the case of specimens with 0% initial moisture content and 5.1–11.4 in the case of specimens with 25% initial moisture content. The higher initial moisture content produced a more uniform acceleration coefficient. Nevertheless, larger acceleration coefficients were derived from specimens with penetrating or semi-film-forming coatings in both cases. The relationships between the uniformity of this acceleration coefficient and the initial moisture content are discussed from the moisture absorption experiment under constant temperature and humidity and under condensation conditions.
{"title":"Artificial-weathering test requirements for fire-retardant-treated wood to reproduce optimal chemical retention and moisture conditions","authors":"Ryo Takase, Atsuko Ishikawa, Daisuke Kamikawa","doi":"10.1186/s10086-024-02143-3","DOIUrl":"https://doi.org/10.1186/s10086-024-02143-3","url":null,"abstract":"Despite the increasing outdoor use of fire-retardant-treated wood, methods for predicting its service life remain poorly established. With the aim of establishing a method to predict chemical losses from fire-retardant-treated (FRT) wood caused by humid atmospheres and rain outdoors, this study examined the preferable conditions for artificial-weathering tests and demonstrated the acceleration coefficients in these tests (i.e., the ratio of equivalent time to reach the same retention of chemicals in artificial weathering and outdoors) based on the EN927-6 standard. To determine the moisture absorption and desorption levels of FRT exposed to outdoor conditions, an outdoor exposure experiment was conducted. The moisture content was higher in the FRT wood than in untreated wood, regardless of the type of coating, and ranged between 11% (in March) and 50% (in September) of the untreated wood’s weight. EN927-6 artificial weathering tests were performed on two groups of specimens with initial moisture contents of 0% and 25%. Retention rates of fire-retardant chemicals after a 2520-h test were compared with those retrieved from 4-year outdoor exposure reported elsewhere. Comparison of these two experiments demonstrated that the acceleration coefficients were 4.1–11.3 in the case of specimens with 0% initial moisture content and 5.1–11.4 in the case of specimens with 25% initial moisture content. The higher initial moisture content produced a more uniform acceleration coefficient. Nevertheless, larger acceleration coefficients were derived from specimens with penetrating or semi-film-forming coatings in both cases. The relationships between the uniformity of this acceleration coefficient and the initial moisture content are discussed from the moisture absorption experiment under constant temperature and humidity and under condensation conditions.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"19 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-06-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141496167","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-06-05DOI: 10.1186/s10086-024-02141-5
Y. Kurata, S. Horiuchi, M. Kojima, K. Watanabe, M. Iwasa, H. Abe
There are numerous wooden historical artifacts in Kyoto and other parts of Japan, including Buddhist statues or Shinto deities. The identification of wood species in these historical artifact is desirable for both repair and maintenance purposes. The most common method of identifying wood species involves examining samples taken from the artifacts. However, intentional sampling from old cultural artifacts is prohibited in Japan. As a result, we attempted to determine the wood species of old statues non-destructively using near-infrared spectroscopy (NIRS). In this article, we developed the softwood and hardwood separation model using NIRS to compare the prediction accuracy for few algorithms. The model was created based on wood samples stored in the xylarium of the Forestry and Forest Products Research Institute (TWTw). We then applied this model to old Buddhist statues in order to classify them as either softwood or hardwood. These Buddhist statues were housed in Nazenji temple and are believed to have been carved during the Heian period (8th–12th century). For the near-infrared (NIR) measurements, we collected diffuse reflectance spectra from TWTw sample and Buddhist statues using same spectrometer. Initially, we used the soft independent modeling of class analogy method (SIMCA), partial least squares discriminant analysis (PLS_DA), and support vector machine to analyze the NIR spectra obtained from the TWTw wood samples. Subsequently, we applied the NIR spectra obtained from several Buddhist statues in Nazenji temple to the aforementioned separation model and determined whether spectra data were classified as the softwood or hardwood. Finally, wood specimens detached naturally from the Buddhist statues over time were observed under microscopic analysis to identify the wood species. As comparing the prediction accuracy of few algorithms, SIMCA had a poor result, but PLS_DA had a good result. PLS_DA had better discrimination because it performed calculations to improve regression from both explanatory variables and objective variables.
{"title":"The utilization of wood samples from xylarium in historical wooden statues: improving the separation accuracy non-destructive measurement for using several algorithms","authors":"Y. Kurata, S. Horiuchi, M. Kojima, K. Watanabe, M. Iwasa, H. Abe","doi":"10.1186/s10086-024-02141-5","DOIUrl":"https://doi.org/10.1186/s10086-024-02141-5","url":null,"abstract":"There are numerous wooden historical artifacts in Kyoto and other parts of Japan, including Buddhist statues or Shinto deities. The identification of wood species in these historical artifact is desirable for both repair and maintenance purposes. The most common method of identifying wood species involves examining samples taken from the artifacts. However, intentional sampling from old cultural artifacts is prohibited in Japan. As a result, we attempted to determine the wood species of old statues non-destructively using near-infrared spectroscopy (NIRS). In this article, we developed the softwood and hardwood separation model using NIRS to compare the prediction accuracy for few algorithms. The model was created based on wood samples stored in the xylarium of the Forestry and Forest Products Research Institute (TWTw). We then applied this model to old Buddhist statues in order to classify them as either softwood or hardwood. These Buddhist statues were housed in Nazenji temple and are believed to have been carved during the Heian period (8th–12th century). For the near-infrared (NIR) measurements, we collected diffuse reflectance spectra from TWTw sample and Buddhist statues using same spectrometer. Initially, we used the soft independent modeling of class analogy method (SIMCA), partial least squares discriminant analysis (PLS_DA), and support vector machine to analyze the NIR spectra obtained from the TWTw wood samples. Subsequently, we applied the NIR spectra obtained from several Buddhist statues in Nazenji temple to the aforementioned separation model and determined whether spectra data were classified as the softwood or hardwood. Finally, wood specimens detached naturally from the Buddhist statues over time were observed under microscopic analysis to identify the wood species. As comparing the prediction accuracy of few algorithms, SIMCA had a poor result, but PLS_DA had a good result. PLS_DA had better discrimination because it performed calculations to improve regression from both explanatory variables and objective variables.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"3 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-06-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141252116","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
As an important renewable resource, wood is widely used in various industries. When addressing wood defects that limit the amount of wood used during processing, manual inspection and other technologies are not suitable for automated production scenarios. In this paper, we first establish our own dataset, which includes information about multiple tree species and multiple defects types, to enhance the overall applicability of the proposed model. Second, target detection technology involving deep learning is used for defect detection. The conditional parametric convolution (CondConv), Wise-IoU, and BiFormer modules are used to improve upon the latest YOLOv8 algorithm. Based on the experimental findings, the suggested approach exhibits notable improvements in terms of both the mAP@0.5 index and the mAP@0.5:0.95 index, surpassing the performance of the YOLOv8 algorithm by 3.5% and 5.8%, respectively. It also has advantages over other target detection algorithms. The proposed method can effectively improve wood utilization and automated wood processing technology.
{"title":"Wood defect detection based on the CWB-YOLOv8 algorithm","authors":"Hao An, Zhihong Liang, Mingming Qin, Yuxiang Huang, Fei Xiong, Guojian Zeng","doi":"10.1186/s10086-024-02139-z","DOIUrl":"https://doi.org/10.1186/s10086-024-02139-z","url":null,"abstract":"As an important renewable resource, wood is widely used in various industries. When addressing wood defects that limit the amount of wood used during processing, manual inspection and other technologies are not suitable for automated production scenarios. In this paper, we first establish our own dataset, which includes information about multiple tree species and multiple defects types, to enhance the overall applicability of the proposed model. Second, target detection technology involving deep learning is used for defect detection. The conditional parametric convolution (CondConv), Wise-IoU, and BiFormer modules are used to improve upon the latest YOLOv8 algorithm. Based on the experimental findings, the suggested approach exhibits notable improvements in terms of both the mAP@0.5 index and the mAP@0.5:0.95 index, surpassing the performance of the YOLOv8 algorithm by 3.5% and 5.8%, respectively. It also has advantages over other target detection algorithms. The proposed method can effectively improve wood utilization and automated wood processing technology.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"52 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-06-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141252121","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-05-13DOI: 10.1186/s10086-024-02132-6
Vanella Mbakop Nanshie, Ali Aidibe, Majid Heidari, Mohammad Jahazi
Squaring, a wood transformation process, is an operation which consists of introducing the logs into a squaring machine which then uses sharp tools to cut the wood into pieces with high surface quality. Tool steels used in this process experience significant wear, damaging the wood surface and hence leading to substantial scrape rate. This study investigates the wear resistance of three tool steels specifically designed for wood cutting applications: modified AISI A8, modified steels with 0% and 1% tungsten, and powder metallurgy prepared W360 steel. Furthermore, the influence of a PVD coating on the wear resistance of the three alloys was investigated. ASTM G65 abrasive wear tests were conducted using the dry sand/rubber wheel abrasion test. A methodology using a non-contact 3D measurement system and specialized software was developed, allowing for a thorough quantitative assessment of the wear of these steels. The results revealed that the coated A8mod + 1%W steel exhibits the best resistance among the coated steels. Despite the excellent intrinsic resistance of W360 steel, the coating did not provide a significant improvement for this steel, showing only a 10% reduction in wear. Microstructural analysis revealed that the predominant wear mechanisms were abrasion and impact. The relative performance of each steel was quantified and is reported. Field trials conducted under actual cutting conditions, indicate the superiority of W360 steel in terms of resilience to wear and impacts compared to other tested alloys, while confirming the effectiveness of surface treatments in mitigating material wear. However, A8 steel modified with 1% tungsten exhibits increased wear under coating.
{"title":"Impact of coating and microstructure on wear resistance of tool steels for wood cutting: a novel approach to quantification and analysis of wear-related damages","authors":"Vanella Mbakop Nanshie, Ali Aidibe, Majid Heidari, Mohammad Jahazi","doi":"10.1186/s10086-024-02132-6","DOIUrl":"https://doi.org/10.1186/s10086-024-02132-6","url":null,"abstract":"Squaring, a wood transformation process, is an operation which consists of introducing the logs into a squaring machine which then uses sharp tools to cut the wood into pieces with high surface quality. Tool steels used in this process experience significant wear, damaging the wood surface and hence leading to substantial scrape rate. This study investigates the wear resistance of three tool steels specifically designed for wood cutting applications: modified AISI A8, modified steels with 0% and 1% tungsten, and powder metallurgy prepared W360 steel. Furthermore, the influence of a PVD coating on the wear resistance of the three alloys was investigated. ASTM G65 abrasive wear tests were conducted using the dry sand/rubber wheel abrasion test. A methodology using a non-contact 3D measurement system and specialized software was developed, allowing for a thorough quantitative assessment of the wear of these steels. The results revealed that the coated A8mod + 1%W steel exhibits the best resistance among the coated steels. Despite the excellent intrinsic resistance of W360 steel, the coating did not provide a significant improvement for this steel, showing only a 10% reduction in wear. Microstructural analysis revealed that the predominant wear mechanisms were abrasion and impact. The relative performance of each steel was quantified and is reported. Field trials conducted under actual cutting conditions, indicate the superiority of W360 steel in terms of resilience to wear and impacts compared to other tested alloys, while confirming the effectiveness of surface treatments in mitigating material wear. However, A8 steel modified with 1% tungsten exhibits increased wear under coating.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"24 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-05-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140935308","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-05-13DOI: 10.1186/s10086-024-02134-4
Harumi Ikei, Hyunju Jo, Yoshifumi Miyazaki
In Japanese households, it is customary to walk barefoot on wooden floors. Previous reports on the psychological and physiological relaxing effects of feet contact with uncoated solid wood have already been published. However, there are no studies on the effects of feet contact with coated wood, which is commonly used for residential floors. This study aimed to validate the psychological and physiological relaxing effects of sole contact with oil-finished wood. In total, 27 women university students (mean age: 21.9 ± 1.9 years) participated in this study. Psychological indices such as the modified semantic differential method and the Profile of Mood States Second Edition were used. The oxyhemoglobin (oxy-Hb) concentrations in the prefrontal cortex were determined using near-infrared time-resolved spectroscopy. The sympathetic nervous activity and the parasympathetic nervous activity were measured using heart rate variability. The flat plate for tactile stimulation was oil-finished wood, and uncoated wood and marble were used for comparison. The sole of the feet of each participant touched each material for 90 s. Feet contact with oil-finished and uncoated wood had relaxing effects on psychological and physiological responses compared with marble. The relaxing effects of oil-finished wood and uncoated wood were similar. That is, they significantly increased subjective feelings of comfort and relaxation, improved mood states, and decreased oxy-Hb concentration in the left prefrontal cortex compared with marble. However, there were no statistically significant differences in terms of right prefrontal cortex and sympathetic nervous activities between oil-finished wood and marble. Oil-finished wood had a slightly weaker physiological relaxation effect than uncoated wood.
{"title":"Psychological and physiological effects of sole contact with oil-finished wood","authors":"Harumi Ikei, Hyunju Jo, Yoshifumi Miyazaki","doi":"10.1186/s10086-024-02134-4","DOIUrl":"https://doi.org/10.1186/s10086-024-02134-4","url":null,"abstract":"In Japanese households, it is customary to walk barefoot on wooden floors. Previous reports on the psychological and physiological relaxing effects of feet contact with uncoated solid wood have already been published. However, there are no studies on the effects of feet contact with coated wood, which is commonly used for residential floors. This study aimed to validate the psychological and physiological relaxing effects of sole contact with oil-finished wood. In total, 27 women university students (mean age: 21.9 ± 1.9 years) participated in this study. Psychological indices such as the modified semantic differential method and the Profile of Mood States Second Edition were used. The oxyhemoglobin (oxy-Hb) concentrations in the prefrontal cortex were determined using near-infrared time-resolved spectroscopy. The sympathetic nervous activity and the parasympathetic nervous activity were measured using heart rate variability. The flat plate for tactile stimulation was oil-finished wood, and uncoated wood and marble were used for comparison. The sole of the feet of each participant touched each material for 90 s. Feet contact with oil-finished and uncoated wood had relaxing effects on psychological and physiological responses compared with marble. The relaxing effects of oil-finished wood and uncoated wood were similar. That is, they significantly increased subjective feelings of comfort and relaxation, improved mood states, and decreased oxy-Hb concentration in the left prefrontal cortex compared with marble. However, there were no statistically significant differences in terms of right prefrontal cortex and sympathetic nervous activities between oil-finished wood and marble. Oil-finished wood had a slightly weaker physiological relaxation effect than uncoated wood.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"5 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-05-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140935376","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-04-15DOI: 10.1186/s10086-024-02129-1
Kota Enomoto, Takashi Hosoya, Hisashi Miyafuji
Furan compounds, including 5-hydroxymethylfurfural and furfural, can be synthesized from biomass and have garnered attention for their potential applications in biofuels and resin precursors. In this study, the synthesis of the furan compounds from rice straw was explored using a combined approach of ionic liquid treatment, specifically 1-methylimidazolium hydrogen sulfate ([MIM]HSO4), and vacuum steam distillation. Through the optimization of various processing parameters, we established that the best conditions for the furan compound production include: a cold trap cooling temperature of – 196 ℃, a system pressure of 10 hPa, a treatment temperature of 180 ℃, a reaction duration of 30 min, a sample loading of 1wt%, and a particle size range of 45–90 µm. Under these conditions, the resultant yield of the furan compounds was quantified at 27.9wt%. Additionally, the recyclability of the utilized ionic liquid was evaluated. Notably, even after four recycling cycles (encompassing a total of five reactions), the yield of the furan compounds remained consistent, underscoring the viability of ionic liquid reuse.
{"title":"Production and recovery system for furan compounds from rice straw using an ionic liquid (1-methylimidazolium hydrogen sulfate) and vacuum steam distillation","authors":"Kota Enomoto, Takashi Hosoya, Hisashi Miyafuji","doi":"10.1186/s10086-024-02129-1","DOIUrl":"https://doi.org/10.1186/s10086-024-02129-1","url":null,"abstract":"Furan compounds, including 5-hydroxymethylfurfural and furfural, can be synthesized from biomass and have garnered attention for their potential applications in biofuels and resin precursors. In this study, the synthesis of the furan compounds from rice straw was explored using a combined approach of ionic liquid treatment, specifically 1-methylimidazolium hydrogen sulfate ([MIM]HSO4), and vacuum steam distillation. Through the optimization of various processing parameters, we established that the best conditions for the furan compound production include: a cold trap cooling temperature of – 196 ℃, a system pressure of 10 hPa, a treatment temperature of 180 ℃, a reaction duration of 30 min, a sample loading of 1wt%, and a particle size range of 45–90 µm. Under these conditions, the resultant yield of the furan compounds was quantified at 27.9wt%. Additionally, the recyclability of the utilized ionic liquid was evaluated. Notably, even after four recycling cycles (encompassing a total of five reactions), the yield of the furan compounds remained consistent, underscoring the viability of ionic liquid reuse.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"2019 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-04-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140569958","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-04-11DOI: 10.1186/s10086-024-02131-7
Tomohiko Matsuzawa, Rie Tai, Hiroyuki Mano, Isamu Ogura
In parallel with the development of novel materials, such as cellulose nanofibers (CNFs), their effects on aquatic organisms should be evaluated. In ecotoxicity testing, concentration measurements are important to obtain accurate exposure concentrations; however, few studies have measured the concentration and dispersion state of CNFs in test solutions. Therefore, we evaluated the applicability of enzymatic and phenol–sulfuric acid methods for CNF quantification in ecotoxicity testing. In the enzymatic method, CNF content was determined by quantifying the d-glucose produced from the CNFs using cellulase with a glucose assay kit. Three types of cellulases were purchased, and impurities such as d-glucose were identified and removed. The differences in CNF degradation efficiency among the cellulases were evaluated, and a cellulase suitable for CNF degradation was selected. In the phenol–sulfuric acid method, a microplate-based method was employed to handle a large number of samples. We demonstrated that both the enzymatic and phenol–sulfuric acid methods could quantify CNFs in media for ecotoxicity testing. The enzymatic method was able to measure lower CNF concentrations (~ 1 mg/L) than the phenol–sulfuric acid method (~ 10 mg/L) and had less interference with CNF quantification by algae and non-cellulosic polysaccharides.
{"title":"Applicability of enzymatic and phenol–sulfuric acid methods for determination of cellulose nanofibers in ecotoxicity testing","authors":"Tomohiko Matsuzawa, Rie Tai, Hiroyuki Mano, Isamu Ogura","doi":"10.1186/s10086-024-02131-7","DOIUrl":"https://doi.org/10.1186/s10086-024-02131-7","url":null,"abstract":"In parallel with the development of novel materials, such as cellulose nanofibers (CNFs), their effects on aquatic organisms should be evaluated. In ecotoxicity testing, concentration measurements are important to obtain accurate exposure concentrations; however, few studies have measured the concentration and dispersion state of CNFs in test solutions. Therefore, we evaluated the applicability of enzymatic and phenol–sulfuric acid methods for CNF quantification in ecotoxicity testing. In the enzymatic method, CNF content was determined by quantifying the d-glucose produced from the CNFs using cellulase with a glucose assay kit. Three types of cellulases were purchased, and impurities such as d-glucose were identified and removed. The differences in CNF degradation efficiency among the cellulases were evaluated, and a cellulase suitable for CNF degradation was selected. In the phenol–sulfuric acid method, a microplate-based method was employed to handle a large number of samples. We demonstrated that both the enzymatic and phenol–sulfuric acid methods could quantify CNFs in media for ecotoxicity testing. The enzymatic method was able to measure lower CNF concentrations (~ 1 mg/L) than the phenol–sulfuric acid method (~ 10 mg/L) and had less interference with CNF quantification by algae and non-cellulosic polysaccharides.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"78 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-04-11","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140602920","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-04-09DOI: 10.1186/s10086-024-02130-8
Evelyn, Yusnimar, Muhammad Iwan Fermi, Edy Saputra, Syelvia Putri Utami, Komalasari, Sri Wahdini Rahmi, Hiroshi Ohi
The demand for high-purity cellulose, optimization of wood utilization, and environmentally friendly processes has increased in dissolving pulp (DP) production. Sago palm fronds (SPF), an abundant agricultural waste in Indonesia, hold great potential as a raw material for cellulose, hemicellulose, and lignin production. This study aimed to explore the production of from SPF by employing a combination of prehydrolysis, soda cooking with 2-methylanthraquinone (MAQ) as a green additive (PHS-MAQ), and totally chlorine-free (TCF) bleaching with peroxymonosulfuric acid (Psa). Furthermore, lignin was recovered from the black liquor of PHS-MAQ. The results showed that prehydrolysis at 150 ºC for 3 h, followed by soda-MAQ cooking at 160 ºC for 1.5 h using 0.03% of MAQ, 23% active alkali (AA), and a five-stage bleaching with oxygen (O), Psa, alkaline extraction with hydrogen peroxide (Ep), Psa, and Ep successfully produced high-purity cellulose as DP, with properties of 94.3% α-cellulose content, 89.9% ISO brightness (SNI ISO 2470–1:2016), 9.1 cP viscosity, and 0.13% ash content. Moreover, the soda-MAQ cooking method exhibited superior delignification compared to prehydrolysis kraft (PHK) and prehydrolysis soda (PHS) processes in a range of kappa numbers of 9.4–22.6 at 17–25% AA. The inclusion of MAQ increased pulp yields by 4.6–4.9% and decreased kappa number by 1.6–3.1 compared to the PHS without additives at similar AA. Lignin was separated from the PHS-MAQ, with yields of 69–77%. This work demonstrated the suitability of SPF processed by PHS-MAQ cooking and Psa bleaching for the preparation of viscose rayon and cellulose derivatives. The lignin recovery could be an attractive biorefinery process in modern pulp mills.
{"title":"Cellulose and lignin purified from Metroxylon sagu palm fronds by a new technology with 2-methylanthraquinone cooking and peroxymonosulfuric acid bleaching","authors":"Evelyn, Yusnimar, Muhammad Iwan Fermi, Edy Saputra, Syelvia Putri Utami, Komalasari, Sri Wahdini Rahmi, Hiroshi Ohi","doi":"10.1186/s10086-024-02130-8","DOIUrl":"https://doi.org/10.1186/s10086-024-02130-8","url":null,"abstract":"The demand for high-purity cellulose, optimization of wood utilization, and environmentally friendly processes has increased in dissolving pulp (DP) production. Sago palm fronds (SPF), an abundant agricultural waste in Indonesia, hold great potential as a raw material for cellulose, hemicellulose, and lignin production. This study aimed to explore the production of from SPF by employing a combination of prehydrolysis, soda cooking with 2-methylanthraquinone (MAQ) as a green additive (PHS-MAQ), and totally chlorine-free (TCF) bleaching with peroxymonosulfuric acid (Psa). Furthermore, lignin was recovered from the black liquor of PHS-MAQ. The results showed that prehydrolysis at 150 ºC for 3 h, followed by soda-MAQ cooking at 160 ºC for 1.5 h using 0.03% of MAQ, 23% active alkali (AA), and a five-stage bleaching with oxygen (O), Psa, alkaline extraction with hydrogen peroxide (Ep), Psa, and Ep successfully produced high-purity cellulose as DP, with properties of 94.3% α-cellulose content, 89.9% ISO brightness (SNI ISO 2470–1:2016), 9.1 cP viscosity, and 0.13% ash content. Moreover, the soda-MAQ cooking method exhibited superior delignification compared to prehydrolysis kraft (PHK) and prehydrolysis soda (PHS) processes in a range of kappa numbers of 9.4–22.6 at 17–25% AA. The inclusion of MAQ increased pulp yields by 4.6–4.9% and decreased kappa number by 1.6–3.1 compared to the PHS without additives at similar AA. Lignin was separated from the PHS-MAQ, with yields of 69–77%. This work demonstrated the suitability of SPF processed by PHS-MAQ cooking and Psa bleaching for the preparation of viscose rayon and cellulose derivatives. The lignin recovery could be an attractive biorefinery process in modern pulp mills.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"123 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-04-09","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140570116","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-04-02DOI: 10.1186/s10086-024-02128-2
Marcos Fernández-Bautista, Sandra Rivas, Remedios Yáñez, José Luís Alonso, Juan Carlos Parajó
Samples of Eucalyptus globulus wood were processed in a reaction media made up of 1-pentanol, water, and diluted acid catalyst. The effects of selected variables (proportion of 1-pentanol in the reaction media, catalyst charge and temperature) on wood solubilization and on the composition of the various phases from treatments (solids containing cellulose, pentanol-rich phase containing depolymerized lignin, and the aqueous phase concentrating the hemicellulose-derived products) were assessed by Response Surface Methodology. Numerical optimization based on the statistical models allowed the identification of the best operational conditions, under which extensive removal of both lignin and hemicelluloses was reached at good selectivity toward cellulose solubilization. The treated solids achieved near stoichiometric conversion upon enzymatic hydrolysis performed under diverse operational conditions, and the lignin structural analysis provided data typical for hardwoods. The experimental results confirmed the potential of 1-pentanol as a solvent for Eucalyptus globulus wood-based biorefineries.
{"title":"One-pot Eucalyptus globulus wood fractionation in acid-catalyzed mixtures of water and 1-pentanol: an optimization study","authors":"Marcos Fernández-Bautista, Sandra Rivas, Remedios Yáñez, José Luís Alonso, Juan Carlos Parajó","doi":"10.1186/s10086-024-02128-2","DOIUrl":"https://doi.org/10.1186/s10086-024-02128-2","url":null,"abstract":"Samples of Eucalyptus globulus wood were processed in a reaction media made up of 1-pentanol, water, and diluted acid catalyst. The effects of selected variables (proportion of 1-pentanol in the reaction media, catalyst charge and temperature) on wood solubilization and on the composition of the various phases from treatments (solids containing cellulose, pentanol-rich phase containing depolymerized lignin, and the aqueous phase concentrating the hemicellulose-derived products) were assessed by Response Surface Methodology. Numerical optimization based on the statistical models allowed the identification of the best operational conditions, under which extensive removal of both lignin and hemicelluloses was reached at good selectivity toward cellulose solubilization. The treated solids achieved near stoichiometric conversion upon enzymatic hydrolysis performed under diverse operational conditions, and the lignin structural analysis provided data typical for hardwoods. The experimental results confirmed the potential of 1-pentanol as a solvent for Eucalyptus globulus wood-based biorefineries.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"10 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-04-02","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140603460","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2024-03-07DOI: 10.1186/s10086-024-02126-4
Ming Li, Yue Zhao, Feilong Mao, Saiyin Fang, Gezhou Qin, Ning Xu, Daigen Zhu
To assess the damage and fracture behavior of wood under load, a wood damage assessment method was proposed based on acoustic emission (AE) b-values and seismic magnitude difference entropy. First, AE signals from Pinus sylvestris var. mongolica (softwood) and Zelkova schneideriana (hardwood) specimens were collected separately at a sampling frequency of 500 kHz in a three-point bending test. Then, 52 dB was taken as the threshold of the AE event, and the b-value and seismic magnitude difference entropy were calculated at 4-s intervals. Finally, by comparing with the load‒time curve, the b-value and seismic magnitude difference entropy were used to evaluate the damage fracture degree. The results showed that an increase in the b-value indicates the accumulation of strain energy, and vice versa, corresponding to the concentrated release of strain energy. At the same time, the test process can be divided into three stages—elastic, elastic‒plastic and plastic—based on the level of the seismic magnitude difference entropy.
为了评估木材在荷载作用下的损伤和断裂行为，提出了一种基于声发射（AE）b 值和震级差熵的木材损伤评估方法。首先，在三点弯曲试验中以 500 kHz 的采样频率分别采集了松柏（软木）和榉木（硬木）试样的声发射信号。然后，将 52 dB 作为 AE 事件的阈值，以 4 s 为间隔计算 b 值和震级差熵。最后，通过与载荷-时间曲线比较，利用 b 值和震级差熵来评估损伤断裂程度。结果表明，b 值的增加表明应变能的积累，反之则表明应变能的集中释放。同时，根据震级差熵的高低，可将试验过程分为三个阶段--弹性阶段、弹塑性阶段和塑性阶段。
{"title":"Study on damage and fracture characteristics of wood based on acoustic emission b-value and seismic magnitude difference entropy","authors":"Ming Li, Yue Zhao, Feilong Mao, Saiyin Fang, Gezhou Qin, Ning Xu, Daigen Zhu","doi":"10.1186/s10086-024-02126-4","DOIUrl":"https://doi.org/10.1186/s10086-024-02126-4","url":null,"abstract":"To assess the damage and fracture behavior of wood under load, a wood damage assessment method was proposed based on acoustic emission (AE) b-values and seismic magnitude difference entropy. First, AE signals from Pinus sylvestris var. mongolica (softwood) and Zelkova schneideriana (hardwood) specimens were collected separately at a sampling frequency of 500 kHz in a three-point bending test. Then, 52 dB was taken as the threshold of the AE event, and the b-value and seismic magnitude difference entropy were calculated at 4-s intervals. Finally, by comparing with the load‒time curve, the b-value and seismic magnitude difference entropy were used to evaluate the damage fracture degree. The results showed that an increase in the b-value indicates the accumulation of strain energy, and vice versa, corresponding to the concentrated release of strain energy. At the same time, the test process can be divided into three stages—elastic, elastic‒plastic and plastic—based on the level of the seismic magnitude difference entropy.","PeriodicalId":17664,"journal":{"name":"Journal of Wood Science","volume":"70 1","pages":""},"PeriodicalIF":2.9,"publicationDate":"2024-03-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140054711","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":3,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：