Tamás Somogyi, Csenge Madácsi, Barbara Lovas-Bíró, Tamás Zsom, V. Zsom-Muha
The soaking step of dry pulse products' – e.g. chickpeas' – food processing is a time consuming process. Soaking time can be significantly reduced by ultrasonic treatment or using higher processing temperatures. The effect of ultrasonic treatment can be investigated by examining the soaking water characteristics. Ultrasound-assisted soaking of chickpeas was performed at 25, 35 and 45 °C, respectively. Additionally, control samples were also prepared without ultrasonic treatment at the same temperatures. The dynamics of the fitted curve clearly shows the relationship namely the higher the treatment temperature, the faster the hydration of the raw material for both untreated and treated groups. In contrast to control group, swelling rate of 2.00 – except the group 45 °C – is not achieved during ultrasound-assisted soaking. In case of treated group, the swelling rate was about 1.90 for all temperatures applied. The ANOVA test shows that the color of the ultrasonically treated samples was significantly different compared to the control (F (5;12) = 207.86; P < 0.001). Average dry matter content and °Brix value were significantly higher in the ultrasound treated group compared to the control in case of all temperatures. This may indicate the destructive effect of ultrasound, which may cause more components to dissolve out of the raw material by the end of the soaking process.
{"title":"Investigation of soaking water produced by ultrasound-assisted chickpea soaking process","authors":"Tamás Somogyi, Csenge Madácsi, Barbara Lovas-Bíró, Tamás Zsom, V. Zsom-Muha","doi":"10.1556/446.2023.00095","DOIUrl":"https://doi.org/10.1556/446.2023.00095","url":null,"abstract":"The soaking step of dry pulse products' – e.g. chickpeas' – food processing is a time consuming process. Soaking time can be significantly reduced by ultrasonic treatment or using higher processing temperatures. The effect of ultrasonic treatment can be investigated by examining the soaking water characteristics. Ultrasound-assisted soaking of chickpeas was performed at 25, 35 and 45 °C, respectively. Additionally, control samples were also prepared without ultrasonic treatment at the same temperatures. The dynamics of the fitted curve clearly shows the relationship namely the higher the treatment temperature, the faster the hydration of the raw material for both untreated and treated groups. In contrast to control group, swelling rate of 2.00 – except the group 45 °C – is not achieved during ultrasound-assisted soaking. In case of treated group, the swelling rate was about 1.90 for all temperatures applied. The ANOVA test shows that the color of the ultrasonically treated samples was significantly different compared to the control (F (5;12) = 207.86; P < 0.001). Average dry matter content and °Brix value were significantly higher in the ultrasound treated group compared to the control in case of all temperatures. This may indicate the destructive effect of ultrasound, which may cause more components to dissolve out of the raw material by the end of the soaking process.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"11 7","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-12-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"138604380","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Polyphenols from agro-industrial waste particularly of fruit origin are a reliable source of antioxidants and antimicrobials that can be used as natural food additives. Organic solvents play an important role in extracting the polyphenols, however, inefficiency in exerting bioactivity and interference with the organoleptic properties are among the reasons that hinder their use as food additives. These problems can be alleviated by purification. In this study, the effect of resin types and elution solvent for purification of the apple pomace extracts on total phenolic content (TPC) and antioxidants were investigated. Crude ethanolic extracts were purified using amberlite resins (XAD7HP and FPX66) in a glass column (25 × 310 mm). The sorption flow rate was 2 Bed volume (BV) per hour, rinse 2 BV per hour, and desorption was 2 BV per hour. Final wash and regeneration were each done by 2 BV per hour. Polyphenol content and antioxidant capacity were quantified spectrophotometrically using Folin-Ciocalteu and Ferric reducing ability of plasma (FRAP) assays respectively. Polyphenol recovery was 50% in XAD7HP (Lowest) using ethanol and 69% in FPX66 (Highest) using acetone. For the case of FRAP recovery, 76% (Lowest) was observed in FPX66 using ethanol while 93% (Highest) was observed in XAD7HP using acetone. Conclusively, FPX66 is the ideal resin for the purification of apple pomace extracts for enhancing antioxidant activity compared to XAD7HP. Further, acetone seems to be a good desorption solvent compared to ethanol.
{"title":"Purification of the apple pomace polyphenol extract using adsorbent resin","authors":"Faraja Gonelimali, B. Szabó-Nótin, M. Máté","doi":"10.1556/446.2023.00087","DOIUrl":"https://doi.org/10.1556/446.2023.00087","url":null,"abstract":"Polyphenols from agro-industrial waste particularly of fruit origin are a reliable source of antioxidants and antimicrobials that can be used as natural food additives. Organic solvents play an important role in extracting the polyphenols, however, inefficiency in exerting bioactivity and interference with the organoleptic properties are among the reasons that hinder their use as food additives. These problems can be alleviated by purification. In this study, the effect of resin types and elution solvent for purification of the apple pomace extracts on total phenolic content (TPC) and antioxidants were investigated. Crude ethanolic extracts were purified using amberlite resins (XAD7HP and FPX66) in a glass column (25 × 310 mm). The sorption flow rate was 2 Bed volume (BV) per hour, rinse 2 BV per hour, and desorption was 2 BV per hour. Final wash and regeneration were each done by 2 BV per hour. Polyphenol content and antioxidant capacity were quantified spectrophotometrically using Folin-Ciocalteu and Ferric reducing ability of plasma (FRAP) assays respectively. Polyphenol recovery was 50% in XAD7HP (Lowest) using ethanol and 69% in FPX66 (Highest) using acetone. For the case of FRAP recovery, 76% (Lowest) was observed in FPX66 using ethanol while 93% (Highest) was observed in XAD7HP using acetone. Conclusively, FPX66 is the ideal resin for the purification of apple pomace extracts for enhancing antioxidant activity compared to XAD7HP. Further, acetone seems to be a good desorption solvent compared to ethanol.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"31 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139225448","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Munkhnasan Enkhbold, Attila Lőrincz, Majd Elayan, László Friedrich, Attila Solymosi, Balázs Wieszt, Kornél Jáni, Adrienn Tóth
This study investigates the effect of 2% lactic acid and 2% ascorbic acid mixture on the quality parameters of red deer meat and beef. After treatment samples were stored at 4 ± 1 °C. The following meat quality parameters were evaluated: pH, color, and microbiological count on days 1, 7, 14, and 21. The results showed that at the end of the experiment, the pH of the treated samples was slightly higher than the non-treated samples, indicating that the lactic acid and ascorbic acid mixture had a mild acidifying effect on the meat. The color of the treated and non-treated samples did not show any significant difference. However, the microbiological count in the treated samples was lower than the non-treated samples. These findings suggest that an acid mixture could be used as a natural preservative to enhance the microbial safety of red deer meat and beef.
{"title":"Comparison of the effect of organic acid mixture on quality parameters of red deer meat and beef","authors":"Munkhnasan Enkhbold, Attila Lőrincz, Majd Elayan, László Friedrich, Attila Solymosi, Balázs Wieszt, Kornél Jáni, Adrienn Tóth","doi":"10.1556/446.2023.00079","DOIUrl":"https://doi.org/10.1556/446.2023.00079","url":null,"abstract":"This study investigates the effect of 2% lactic acid and 2% ascorbic acid mixture on the quality parameters of red deer meat and beef. After treatment samples were stored at 4 ± 1 °C. The following meat quality parameters were evaluated: pH, color, and microbiological count on days 1, 7, 14, and 21. The results showed that at the end of the experiment, the pH of the treated samples was slightly higher than the non-treated samples, indicating that the lactic acid and ascorbic acid mixture had a mild acidifying effect on the meat. The color of the treated and non-treated samples did not show any significant difference. However, the microbiological count in the treated samples was lower than the non-treated samples. These findings suggest that an acid mixture could be used as a natural preservative to enhance the microbial safety of red deer meat and beef.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"1 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139234097","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Thanh Tung Pham, Z. H. Siyum, Thi Thanh Nga Ha, Hoa Xuan Mac, S. Dam, Trang Ha Dieu Nguyen, Lien Le Phuong Nguyen, L. Baranyai
The presented study investigated the effects of edible coatings with concentration of 2%, 3% and 4% of starch (w/v) on the weight loss and firmness loss of green asparagus during 4 days of storage at room temperature (26 ± 2 °C, 65–70% RH). According to the results, the coated asparagus exhibited significantly slower deterioration rate than the uncoated control samples. This was indicated by the decrease in weight loss and increase in firmness (P < 0.05). After the storage period, the samples treated with 4% starch formula retained the highest quality. Furthermore, the assessment of asparagus quality throughout the storage period involved the use of the line laser scattering technique. Extracted parameters of laser scattering signal discriminated samples with linear discriminant analysis (LDA), in which the correct recognition rate of the treated groups was 75.26% and the storage time was 70.54%. This study showed the potential of laser scattering as a rapid, non-invasive, and practical optical method for assessing the quality of asparagus during storage.
{"title":"Evaluating the quality of green asparagus treated with cassava starch-based coating using laser scattering","authors":"Thanh Tung Pham, Z. H. Siyum, Thi Thanh Nga Ha, Hoa Xuan Mac, S. Dam, Trang Ha Dieu Nguyen, Lien Le Phuong Nguyen, L. Baranyai","doi":"10.1556/446.2023.00083","DOIUrl":"https://doi.org/10.1556/446.2023.00083","url":null,"abstract":"The presented study investigated the effects of edible coatings with concentration of 2%, 3% and 4% of starch (w/v) on the weight loss and firmness loss of green asparagus during 4 days of storage at room temperature (26 ± 2 °C, 65–70% RH). According to the results, the coated asparagus exhibited significantly slower deterioration rate than the uncoated control samples. This was indicated by the decrease in weight loss and increase in firmness (P < 0.05). After the storage period, the samples treated with 4% starch formula retained the highest quality. Furthermore, the assessment of asparagus quality throughout the storage period involved the use of the line laser scattering technique. Extracted parameters of laser scattering signal discriminated samples with linear discriminant analysis (LDA), in which the correct recognition rate of the treated groups was 75.26% and the storage time was 70.54%. This study showed the potential of laser scattering as a rapid, non-invasive, and practical optical method for assessing the quality of asparagus during storage.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"35 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139231715","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Besides their unique taste and texture, mushrooms are a promising source of important nutrients, including dietary fiber, amino acids, minerals, and vitamins. Fresh mushrooms, however, can only endure for a brief time, typically up to three days at ambient conditions. Different methods have been used to preserve mushrooms for a prolonged period, such as drying, cooking, frying, irradiation and fermentation. The objective of the current study is to investigate the effect of different pre-treatments and fermentation on physicochemical, textural, and microbial properties of oyster mushrooms. The fresh oyster mushroom was considered as control and 6 alternative pre-treatment methods were used as; blanching in water, steaming, oven cooking, microwave, High Hydrostatic Pressure and UV Light treatment. Moisture, pH, yield, color, texture, and microbiological analyses were performed on each pre-treatment group before and after fermentation. Our results showed that the quality attributes of oyster mushrooms were significantly affected by the usage of different pre-treatments.
{"title":"Effect of alternative pre-treatments and fermentation on quality characteristics of oyster mushrooms","authors":"Meltem Boylu, G. Hitka, György Kenesei","doi":"10.1556/446.2023.00080","DOIUrl":"https://doi.org/10.1556/446.2023.00080","url":null,"abstract":"Besides their unique taste and texture, mushrooms are a promising source of important nutrients, including dietary fiber, amino acids, minerals, and vitamins. Fresh mushrooms, however, can only endure for a brief time, typically up to three days at ambient conditions. Different methods have been used to preserve mushrooms for a prolonged period, such as drying, cooking, frying, irradiation and fermentation. The objective of the current study is to investigate the effect of different pre-treatments and fermentation on physicochemical, textural, and microbial properties of oyster mushrooms. The fresh oyster mushroom was considered as control and 6 alternative pre-treatment methods were used as; blanching in water, steaming, oven cooking, microwave, High Hydrostatic Pressure and UV Light treatment. Moisture, pH, yield, color, texture, and microbiological analyses were performed on each pre-treatment group before and after fermentation. Our results showed that the quality attributes of oyster mushrooms were significantly affected by the usage of different pre-treatments.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"98 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139231269","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
P. Kumar, D. Székely, L. Szalóki-Dorkó, J. Kereszturi, M. Máté
The aim of the present study was to find the best extraction parameters to obtain the highest amounts of polyphenols and antioxidants from the walnut. Walnut kernels from ‘Alsószentiváni 117’ cultivar were used for extraction. The extraction methods were as the follows:Method 1: shaking water-bath at 50 °C for 30 min.Method 2: shaking water-bath at 50 °C for 30 min, then storing at 5 °C for 20 h.Method 3: shaking water-bath at 40 °C for 30 min.Method 4: shaking water-bath at 40 °C for 30 min, then storing at 5 °C for 20 h.According to our results Method 1 showed the highest FRAP value (34.43 mg AAE g−1), the DPPH value (52,94%) and the highest HPLC peaks for chlorogenic acid, epicatechin and rutin were also seen in extracts obtained using Method 1. TPC values of Method 3 were 26.06 mg GAE g−1 for Method 1 it was 25.65 mg GAE g−1. The results of color values, L* and ΔE* were similar in all extracts as well. In our experiments extraction Method 1 proved to be better than others.
{"title":"Phenolic profile, color parameters and antioxidant activity of walnut kernel extracts as influenced by different time and temperature during extraction","authors":"P. Kumar, D. Székely, L. Szalóki-Dorkó, J. Kereszturi, M. Máté","doi":"10.1556/446.2023.00086","DOIUrl":"https://doi.org/10.1556/446.2023.00086","url":null,"abstract":"The aim of the present study was to find the best extraction parameters to obtain the highest amounts of polyphenols and antioxidants from the walnut. Walnut kernels from ‘Alsószentiváni 117’ cultivar were used for extraction. The extraction methods were as the follows:Method 1: shaking water-bath at 50 °C for 30 min.Method 2: shaking water-bath at 50 °C for 30 min, then storing at 5 °C for 20 h.Method 3: shaking water-bath at 40 °C for 30 min.Method 4: shaking water-bath at 40 °C for 30 min, then storing at 5 °C for 20 h.According to our results Method 1 showed the highest FRAP value (34.43 mg AAE g−1), the DPPH value (52,94%) and the highest HPLC peaks for chlorogenic acid, epicatechin and rutin were also seen in extracts obtained using Method 1. TPC values of Method 3 were 26.06 mg GAE g−1 for Method 1 it was 25.65 mg GAE g−1. The results of color values, L* and ΔE* were similar in all extracts as well. In our experiments extraction Method 1 proved to be better than others.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"7 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139233294","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
This study aimed to assess the effectiveness of two reverse osmosis membranes (RO99 and X20) plus one nanofiltration membrane (NF270) at concentrating hawthorn fruit and anise seed extracts. Extracting the anise was done using water at a temperature of 37 °C over a period of 100 min. For hawthorn, ethanol-water (56%) was used as the solvent and extraction occurred at 55 °C for 80 min. The transmembrane pressure (TMP), temperature, and recirculation flow rate of the membrane separation process were monitored and set at 35 bar, 30 °C, and 400 l/h respectively. Using a spectrophotometer, the quantification of valuable compounds was examined. After studying the flow levels, it was discovered that the X20 membrane had the tiniest alterations in permeability, followed by RO99 and NF270. Moreover, in terms of efficiency, the X-20 outperformed RO-99 and NF-270 membranes, where TPC was increased (20 and 18-fold) for anise seed and hawthorn fruit extracts respectively, and TFC was increased 8-fold for both of the extracts. While using NF-270, TPC was increased only (11 and 6-fold), and TFC (4 and 2-fold) for anise seed and hawthorn fruit extracts respectively. For the antioxidant activity, the process using X-20 showed an improvement of around 12-fold for anise extracts and 15-fold for hawthorn extracts for antioxidant activity. In terms of brix, the anise extracts saw a 3-fold increase and the hawthorn extracts saw a 4-fold boost after going through the X-20 membrane concentration process. Additionally, the X-20 membrane exhibits the highest retention rates for both anise and hawthorn extracts and is least affected by fouling during the concentration process.
{"title":"Evaluation of reverse osmosis and nanofiltration membranes in concentrating hawthorn fruit and anise seed extract","authors":"Areej Alsobh, G. Vatai, Szilvia Bánvölgyi","doi":"10.1556/446.2023.00074","DOIUrl":"https://doi.org/10.1556/446.2023.00074","url":null,"abstract":"This study aimed to assess the effectiveness of two reverse osmosis membranes (RO99 and X20) plus one nanofiltration membrane (NF270) at concentrating hawthorn fruit and anise seed extracts. Extracting the anise was done using water at a temperature of 37 °C over a period of 100 min. For hawthorn, ethanol-water (56%) was used as the solvent and extraction occurred at 55 °C for 80 min. The transmembrane pressure (TMP), temperature, and recirculation flow rate of the membrane separation process were monitored and set at 35 bar, 30 °C, and 400 l/h respectively. Using a spectrophotometer, the quantification of valuable compounds was examined. After studying the flow levels, it was discovered that the X20 membrane had the tiniest alterations in permeability, followed by RO99 and NF270. Moreover, in terms of efficiency, the X-20 outperformed RO-99 and NF-270 membranes, where TPC was increased (20 and 18-fold) for anise seed and hawthorn fruit extracts respectively, and TFC was increased 8-fold for both of the extracts. While using NF-270, TPC was increased only (11 and 6-fold), and TFC (4 and 2-fold) for anise seed and hawthorn fruit extracts respectively. For the antioxidant activity, the process using X-20 showed an improvement of around 12-fold for anise extracts and 15-fold for hawthorn extracts for antioxidant activity. In terms of brix, the anise extracts saw a 3-fold increase and the hawthorn extracts saw a 4-fold boost after going through the X-20 membrane concentration process. Additionally, the X-20 membrane exhibits the highest retention rates for both anise and hawthorn extracts and is least affected by fouling during the concentration process.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"46 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139229380","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Thi Thanh Nga Ha, Thanh Tung Pham, S. Dam, Xuan Hoa Mac, Lien Le Phuong Nguyen, G. Hitka, T. Zsom
This study focuses on the contribution of maturity stages and 1-methylcyclopropene (1-MCP) treatment to the quality of ‘Zebra’ apricot. Samples were harvested at mature-green, yellow and orange maturity stages. Fruit were treated with gaseous 1-MCP (24 h at 1 °C), followed by cold storage at 1 °C for 6 weeks. Non-destructive measurements were used to evaluate the quality changes of apricot during storage. The results showed that the maturity stages significantly affected the weight loss. The loss of weight increased rapidly for orange ripeness stage fruit, more than others during storage. Both maturity and 1-MCP affected the stiffness of apricot. The 1-MCP could delay the softening of fruit. The green and yellow maturity stages retained higher values in stiffness compared to orange. No significant difference in hue angle values was observed between 1-MCP treated and control fruit, however hue angle value decreased strongly in mature-green harvested fruit. The maturity stages and 1-MCP treatment had the effect on quality changes of apricot over storage. The maturity stage was an important factor contributing to the effectiveness of 1-MCP application as it was observed in slower softening after harvest.
{"title":"Effect of 1-methylcyclopropene treatment on quality of ‘Zebra’ apricot harvested at different maturity stages","authors":"Thi Thanh Nga Ha, Thanh Tung Pham, S. Dam, Xuan Hoa Mac, Lien Le Phuong Nguyen, G. Hitka, T. Zsom","doi":"10.1556/446.2023.00084","DOIUrl":"https://doi.org/10.1556/446.2023.00084","url":null,"abstract":"This study focuses on the contribution of maturity stages and 1-methylcyclopropene (1-MCP) treatment to the quality of ‘Zebra’ apricot. Samples were harvested at mature-green, yellow and orange maturity stages. Fruit were treated with gaseous 1-MCP (24 h at 1 °C), followed by cold storage at 1 °C for 6 weeks. Non-destructive measurements were used to evaluate the quality changes of apricot during storage. The results showed that the maturity stages significantly affected the weight loss. The loss of weight increased rapidly for orange ripeness stage fruit, more than others during storage. Both maturity and 1-MCP affected the stiffness of apricot. The 1-MCP could delay the softening of fruit. The green and yellow maturity stages retained higher values in stiffness compared to orange. No significant difference in hue angle values was observed between 1-MCP treated and control fruit, however hue angle value decreased strongly in mature-green harvested fruit. The maturity stages and 1-MCP treatment had the effect on quality changes of apricot over storage. The maturity stage was an important factor contributing to the effectiveness of 1-MCP application as it was observed in slower softening after harvest.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"77 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139233687","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
O. Haykir, R. Forrez, G. Mathijssen, B. Vanderborght
The food robotics revolution is driving a shift in the vending machine sector from conventional pre-packaged sales to on-site food manufacture. As these machines develop into small-scale food processing points, it is critical to guarantee food safety. The implementation of automated Clean-in-Place (CIP) techniques, in addition to manual cleaning, is modelled after food production practices, where hygiene is maintained without direct human intervention. These days, running these modern, multifunctional vending machines requires giving the highest priority to food safety and putting rigorous control measures in practice.This case study aimed to implement a CIP procedure in a vending machine and assess microbial contamination. Water, blender, and smoothies were microbiologically analyzed to evaluate the microbial safety of ingredients, equipment, and the final product.Microbiological analysis showed that none of the samples was contaminated with three major pathogens: Listeria monocytogenes, Salmonella spp., and Escherichia coli. This study showed the importance of the Clean-in-Place (CIP) process in automated vending machines.
{"title":"Food safety and quality assessment of an automated vending machine for smoothies – A case study","authors":"O. Haykir, R. Forrez, G. Mathijssen, B. Vanderborght","doi":"10.1556/446.2023.00077","DOIUrl":"https://doi.org/10.1556/446.2023.00077","url":null,"abstract":"The food robotics revolution is driving a shift in the vending machine sector from conventional pre-packaged sales to on-site food manufacture. As these machines develop into small-scale food processing points, it is critical to guarantee food safety. The implementation of automated Clean-in-Place (CIP) techniques, in addition to manual cleaning, is modelled after food production practices, where hygiene is maintained without direct human intervention. These days, running these modern, multifunctional vending machines requires giving the highest priority to food safety and putting rigorous control measures in practice.This case study aimed to implement a CIP procedure in a vending machine and assess microbial contamination. Water, blender, and smoothies were microbiologically analyzed to evaluate the microbial safety of ingredients, equipment, and the final product.Microbiological analysis showed that none of the samples was contaminated with three major pathogens: Listeria monocytogenes, Salmonella spp., and Escherichia coli. This study showed the importance of the Clean-in-Place (CIP) process in automated vending machines.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"26 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139231060","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Hoa Xuan Mac, Nga Thi Thanh Ha, Lien Le Phuong Nguyen, L. Baranyai
In this work, the simulated adulteration of coconut drink by dilution with water was investigated using laser-light backscattering (LLB) imaging. The laser vision system consisted of six low power laser modules, emitting 1 mm diameter beams at wavelengths of 532, 635, 780, 808, 850 and 1,064 nm. The backscattering images were acquired by a grey scale camera with 12 bit resolution. Eight parameters were extracted to describe the backscattering profile. The methods of linear discriminant analysis (LDA) and partial least squares (PLS) regression were performed on LLB parameters for classifying and predicting dilution level of adulterated coconut drink samples. Based on the results, LLB signals responded sensitively to adulteration. LDA results showed that adulterated samples were correctly recognized with accuracies between 60 and 100%. PLS models were able to estimate the adulteration level of samples with coefficients of determination of 0.57–0.97 in validation. This result demonstrated the potential of laser-light backscattering imaging as a rapid and non-destructive optical technique for evaluation of coconut drink adulteration.
{"title":"A novel approach for determining coconut drink adulteration by means of laser light backscattering imaging","authors":"Hoa Xuan Mac, Nga Thi Thanh Ha, Lien Le Phuong Nguyen, L. Baranyai","doi":"10.1556/446.2023.00082","DOIUrl":"https://doi.org/10.1556/446.2023.00082","url":null,"abstract":"In this work, the simulated adulteration of coconut drink by dilution with water was investigated using laser-light backscattering (LLB) imaging. The laser vision system consisted of six low power laser modules, emitting 1 mm diameter beams at wavelengths of 532, 635, 780, 808, 850 and 1,064 nm. The backscattering images were acquired by a grey scale camera with 12 bit resolution. Eight parameters were extracted to describe the backscattering profile. The methods of linear discriminant analysis (LDA) and partial least squares (PLS) regression were performed on LLB parameters for classifying and predicting dilution level of adulterated coconut drink samples. Based on the results, LLB signals responded sensitively to adulteration. LDA results showed that adulterated samples were correctly recognized with accuracies between 60 and 100%. PLS models were able to estimate the adulteration level of samples with coefficients of determination of 0.57–0.97 in validation. This result demonstrated the potential of laser-light backscattering imaging as a rapid and non-destructive optical technique for evaluation of coconut drink adulteration.","PeriodicalId":20837,"journal":{"name":"Progress in Agricultural Engineering Sciences","volume":"46 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-11-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139241254","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：