Mahdi J. Hussein, Kamal Ali Mohammed, Fatimah H. Naser
Abstract This study targeted to investigate a type of excavation slurry by local available material in Najaf region. On the other hand, chief practises is supported the deep sides of foundation in particular pile foundation and, drilling oil wells. The results of slurries are checking, for seven properties, which includes the viscosity (apparent plastic and funnel Marsh), yield stress, density, acidity, and gel power (10–0 min). Which are 11.7367, 8.8733, 38.1667, 11.5467 mPa·s, 1.1045 kg m −3 , 10.9067, and 11.2683 mPa·s, respectively. On the basis of the results tests for the above properties, that is possible to produce a product that conforms to the specifications of American Petroleum Institute specifications, and according to the requirements of the standard ACI 336.3R-93:2006 without additives. The rheological behavior improvement is achieved through the breakdown of the bundles of palygorskite fibers that normally make up the texture of these mudstones by increasing the time and speed of the shear force as soon as increasing the concentration of clay powder.
摘要本研究针对纳杰夫地区一种利用当地可利用材料的开挖浆体进行研究。另一方面,主要的做法是在深侧基础特别是桩基础和钻油井进行支撑。检查浆料的7项性能,包括粘度(表观塑性和漏斗沼泽)、屈服应力、密度、酸度和凝胶力(10-0分钟)。分别为11.7367、8.8733、38.1667、11.5467 mPa·s、1.1045 kg m−3、10.9067、11.2683 mPa·s。根据上述性能的测试结果,可以生产出符合美国石油协会规格的产品,并根据标准ACI 336.3R-93:2006的要求,不含添加剂。随着粘土粉浓度的增加,随着剪切力的时间和速度的增加,通常构成这些泥岩结构的坡缕石纤维束被破坏,从而实现了流变行为的改善。
{"title":"Assessment of excavation slurry produced clayey mineral from the Bahr Al-Najaf region","authors":"Mahdi J. Hussein, Kamal Ali Mohammed, Fatimah H. Naser","doi":"10.1556/606.2023.00893","DOIUrl":"https://doi.org/10.1556/606.2023.00893","url":null,"abstract":"Abstract This study targeted to investigate a type of excavation slurry by local available material in Najaf region. On the other hand, chief practises is supported the deep sides of foundation in particular pile foundation and, drilling oil wells. The results of slurries are checking, for seven properties, which includes the viscosity (apparent plastic and funnel Marsh), yield stress, density, acidity, and gel power (10–0 min). Which are 11.7367, 8.8733, 38.1667, 11.5467 mPa·s, 1.1045 kg m −3 , 10.9067, and 11.2683 mPa·s, respectively. On the basis of the results tests for the above properties, that is possible to produce a product that conforms to the specifications of American Petroleum Institute specifications, and according to the requirements of the standard ACI 336.3R-93:2006 without additives. The rheological behavior improvement is achieved through the breakdown of the bundles of palygorskite fibers that normally make up the texture of these mudstones by increasing the time and speed of the shear force as soon as increasing the concentration of clay powder.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135858736","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract Building information modeling is one of the trends in the modern construction industry. The use of 4D building information modeling in addition to 3D building information modeling improves project planning and leads to higher quality of the final product with minimal wastage of resources. In addition, 4D building information modeling allows creating visual effects that can be shown to clients before construction begins. The study describes the ways in which 4D building information modeling can be used, as well as some of the notable benefits. The level of awareness of this technology and the level of its use in construction practice are also described. The final part describes the main problems and tasks of this field and possible ways to solve them.
{"title":"Overview of the level of 4D BIM integration in the construction industry in Slovakia","authors":"Yaroslav Nechyporchuk, Renáta Baškova","doi":"10.1556/606.2023.00783","DOIUrl":"https://doi.org/10.1556/606.2023.00783","url":null,"abstract":"Abstract Building information modeling is one of the trends in the modern construction industry. The use of 4D building information modeling in addition to 3D building information modeling improves project planning and leads to higher quality of the final product with minimal wastage of resources. In addition, 4D building information modeling allows creating visual effects that can be shown to clients before construction begins. The study describes the ways in which 4D building information modeling can be used, as well as some of the notable benefits. The level of awareness of this technology and the level of its use in construction practice are also described. The final part describes the main problems and tasks of this field and possible ways to solve them.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135858883","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract Fair treatment of individuals in a scheduling task is essential. Unfairness can cause dissatisfaction among workers, faster obsolescence of work tools and underutilization of others. The literature's definitions vary, and there is no clear definition of general scheduling tasks. This article explores fair scheduling through the lens of final exams, aiming to extend decision support system methodologies. It proposes a method based on Lipschitz mapping to measure fairness and presents a pseudo-algorithm for estimating optimal trend lines. The model and the algorithm are demonstrated using the example of final exam schedules. In this way, two feasible solutions can be measured and compared in terms of fairness.
{"title":"Exploring fair scheduling aspects – Through final exam scheduling","authors":"Szilvia Jáhn-Erdős, Bence Kővári","doi":"10.1556/606.2023.00780","DOIUrl":"https://doi.org/10.1556/606.2023.00780","url":null,"abstract":"Abstract Fair treatment of individuals in a scheduling task is essential. Unfairness can cause dissatisfaction among workers, faster obsolescence of work tools and underutilization of others. The literature's definitions vary, and there is no clear definition of general scheduling tasks. This article explores fair scheduling through the lens of final exams, aiming to extend decision support system methodologies. It proposes a method based on Lipschitz mapping to measure fairness and presents a pseudo-algorithm for estimating optimal trend lines. The model and the algorithm are demonstrated using the example of final exam schedules. In this way, two feasible solutions can be measured and compared in terms of fairness.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135858871","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract The paper deals with the capacitance of cylindrical two-dimensional capacitor which consists of Cartesian orthotropic dielectric material. The determination of the capacitance of capacitor with orthotropic dielectric material by a suitable coordinate transformation is reduced to the computation of capacitance of an isotropic capacitor. It is proven that the capacitance of a Cartesian orthotropic capacitor can be obtained in terms of an isotropic capacitor whose dielectric constant is the geometric mean of the dielectric constant of the orthotropic capacitor.
{"title":"Determination of the capacitance of capacitor with orthotropic dielectric material","authors":"István Ecsedi, Ákos József Lengyel","doi":"10.1556/606.2023.00828","DOIUrl":"https://doi.org/10.1556/606.2023.00828","url":null,"abstract":"Abstract The paper deals with the capacitance of cylindrical two-dimensional capacitor which consists of Cartesian orthotropic dielectric material. The determination of the capacitance of capacitor with orthotropic dielectric material by a suitable coordinate transformation is reduced to the computation of capacitance of an isotropic capacitor. It is proven that the capacitance of a Cartesian orthotropic capacitor can be obtained in terms of an isotropic capacitor whose dielectric constant is the geometric mean of the dielectric constant of the orthotropic capacitor.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135917785","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract This study introduces the Chaotic Particle Swarm Optimization as an innovative variant of the traditional particle swarm optimization algorithm, addressing the issue of particle swarm optimization getting trapped in local minima with a low convergence characteristic during later iterations. Chaotic particle swarm optimization incorporates principles from chaos theory to enhance the swarm's exploration and exploitation capabilities. By introducing controlled chaotic behavior, particles exhibit more diverse and unpredictable movements in the search space, leading to improved global convergence and escape from local minima. The proposed method has been implemented and evaluated on benchmark problems to assess its effectiveness. The integration of chaos theory with particle swarm optimization offers promising opportunities for developing robust and efficient optimization techniques suitable for complex and dynamic problem domains in various real-world applications.
{"title":"Study of convergence speed of chaotic particle swarm optimization algorithm","authors":"Bhanu Sekhar Obbu, Zmrooda Jabeen","doi":"10.1556/606.2023.00933","DOIUrl":"https://doi.org/10.1556/606.2023.00933","url":null,"abstract":"Abstract This study introduces the Chaotic Particle Swarm Optimization as an innovative variant of the traditional particle swarm optimization algorithm, addressing the issue of particle swarm optimization getting trapped in local minima with a low convergence characteristic during later iterations. Chaotic particle swarm optimization incorporates principles from chaos theory to enhance the swarm's exploration and exploitation capabilities. By introducing controlled chaotic behavior, particles exhibit more diverse and unpredictable movements in the search space, leading to improved global convergence and escape from local minima. The proposed method has been implemented and evaluated on benchmark problems to assess its effectiveness. The integration of chaos theory with particle swarm optimization offers promising opportunities for developing robust and efficient optimization techniques suitable for complex and dynamic problem domains in various real-world applications.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136358811","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract The models compared in this study were applied to a catchment located in the western part of Slovakia in order to analyze and compare the amount of soil loss in different periods. Using of the empirical model universal soil loss equation, the average annual soil loss in the pilot basin was modeled for 2015–2020. The universal soil loss equation includes a topographic factor modeled using the USLE2D external model. In order to compare the empirical model and the physically-based model a continual sequence of individual rainfall events was created and used as an input to the physically-based EROSION-3D model. The results reflect different behaviors of erosion processes in a catchment together with a comparison between empirical and physically-based approaches.
{"title":"Two different soil erosion modeling approaches in a small experimental area","authors":"Matúš Tomaščík, Michaela Danáčová, Zuzana Németová","doi":"10.1556/606.2023.00835","DOIUrl":"https://doi.org/10.1556/606.2023.00835","url":null,"abstract":"Abstract The models compared in this study were applied to a catchment located in the western part of Slovakia in order to analyze and compare the amount of soil loss in different periods. Using of the empirical model universal soil loss equation, the average annual soil loss in the pilot basin was modeled for 2015–2020. The universal soil loss equation includes a topographic factor modeled using the USLE2D external model. In order to compare the empirical model and the physically-based model a continual sequence of individual rainfall events was created and used as an input to the physically-based EROSION-3D model. The results reflect different behaviors of erosion processes in a catchment together with a comparison between empirical and physically-based approaches.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136357468","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract The role of building orientation in decreasing energy consumption for cooling purposes was examined in this study. A radiation analysis was performed during the early stage of the architectural design process on a proposed four-story apartment building located in Cebu. The building's performance was evaluated using the Grasshopper Ladybug plugin on a 3D model developed in Rhinoceros. Results indicated that the optimal building orientation that produced the lowest total radiation was situated at 290° from the center of the building, with a recorded value of 731,356 kWh m −2 . Conversely, the building orientation that resulted in the highest total radiation was recorded at 210°, with a value of 755,596 kWh m −2 . The analysis results were utilized to make informed decisions about building orientation based on environmental factors and surrounding areas. The use of computational design tools in the early stages of architecture design improves the process by enabling designers to optimize building performance and identify potential design issues early, thereby avoiding costly problems.
摘要:本研究考察了建筑朝向在降低制冷能耗中的作用。在建筑设计过程的早期阶段,对位于宿务的一栋拟议的四层公寓楼进行了辐射分析。建筑的性能是使用Grasshopper Ladybug插件在rhino开发的3D模型上进行评估的。结果表明,总辐射最低的最佳建筑朝向位于距离建筑中心290°处,记录值为731,356 kWh m−2。相反,导致最高总辐射的建筑朝向为210°,其值为755,596 kWh m - 2。分析结果被用于根据环境因素和周围区域做出关于建筑朝向的明智决策。在建筑设计的早期阶段使用计算设计工具,使设计师能够优化建筑性能,及早发现潜在的设计问题,从而避免昂贵的问题,从而改善了整个过程。
{"title":"Building orientation radiation analysis: An early design study using Ladybug","authors":"Rowell Ray Lim Shih","doi":"10.1556/606.2023.00848","DOIUrl":"https://doi.org/10.1556/606.2023.00848","url":null,"abstract":"Abstract The role of building orientation in decreasing energy consumption for cooling purposes was examined in this study. A radiation analysis was performed during the early stage of the architectural design process on a proposed four-story apartment building located in Cebu. The building's performance was evaluated using the Grasshopper Ladybug plugin on a 3D model developed in Rhinoceros. Results indicated that the optimal building orientation that produced the lowest total radiation was situated at 290° from the center of the building, with a recorded value of 731,356 kWh m −2 . Conversely, the building orientation that resulted in the highest total radiation was recorded at 210°, with a value of 755,596 kWh m −2 . The analysis results were utilized to make informed decisions about building orientation based on environmental factors and surrounding areas. The use of computational design tools in the early stages of architecture design improves the process by enabling designers to optimize building performance and identify potential design issues early, thereby avoiding costly problems.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136358801","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract The main purpose of this paper is to propose a model for estimating the hysteresis damping ratio of moment steel frames and compare them with the results obtained using direct displacement-based design. In this study, different models of steel bending frames were examined by using several type of analysis to obtain this ratio. Thirty-steel frame models with 3, 6, 9, 12, and 15 floors and 3 and 6 bay with 6 m span length were analyzed and evaluated. The results showed that the equivalent damping ratio at the level of safety based on Jacobsen and Jennings, and the values of the equivalent damping relationships according to FEMA-440 vary from the empirical formula proposed in displacement-based design-2012. Therefore, in the ductility domain the exponential relationship form was more consistent with the results used. A new formula was proposed to calculate the hysteresis damping ratio, and it is more accurate than the empirical formula proposed in displacement-based design-2012.
{"title":"Hysteresis damping ratio for moment steel frame evaluation using DDBD","authors":"Hussein Kareem Sultan","doi":"10.1556/606.2023.00936","DOIUrl":"https://doi.org/10.1556/606.2023.00936","url":null,"abstract":"Abstract The main purpose of this paper is to propose a model for estimating the hysteresis damping ratio of moment steel frames and compare them with the results obtained using direct displacement-based design. In this study, different models of steel bending frames were examined by using several type of analysis to obtain this ratio. Thirty-steel frame models with 3, 6, 9, 12, and 15 floors and 3 and 6 bay with 6 m span length were analyzed and evaluated. The results showed that the equivalent damping ratio at the level of safety based on Jacobsen and Jennings, and the values of the equivalent damping relationships according to FEMA-440 vary from the empirical formula proposed in displacement-based design-2012. Therefore, in the ductility domain the exponential relationship form was more consistent with the results used. A new formula was proposed to calculate the hysteresis damping ratio, and it is more accurate than the empirical formula proposed in displacement-based design-2012.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135546340","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Abstract Expansive unsaturated soils present challenges in construction due to their moisture-induced behavior. This study proposes empirical equations to estimate the maximum wetting depth over time. Laboratory experiments and numerical analyses using SEEP/W software investigate wetting depth considering time and sand content in coastal and inland regions. Results reveal the significant influence of sand content on maximum soil moisture depth, emphasizing a recommended content above 30% to mitigate heave. The equations offer practical tools for assessing wetting depth, accounting for temporal and spatial variations. This research highlights the importance of wetting depth in addressing soil-related concerns and provides a foundation for further exploration of related factors.
{"title":"Impact of soil composition on maximum depth of wetting in expansive soils","authors":"Ammar Alnmr","doi":"10.1556/606.2023.00870","DOIUrl":"https://doi.org/10.1556/606.2023.00870","url":null,"abstract":"Abstract Expansive unsaturated soils present challenges in construction due to their moisture-induced behavior. This study proposes empirical equations to estimate the maximum wetting depth over time. Laboratory experiments and numerical analyses using SEEP/W software investigate wetting depth considering time and sand content in coastal and inland regions. Results reveal the significant influence of sand content on maximum soil moisture depth, emphasizing a recommended content above 30% to mitigate heave. The equations offer practical tools for assessing wetting depth, accounting for temporal and spatial variations. This research highlights the importance of wetting depth in addressing soil-related concerns and provides a foundation for further exploration of related factors.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135546341","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Myroslav Malovanyy, Roman Paraniak, Ivan Tymchuk, Volodymyr Zhuk, Iryna Ablieieva, Mariia Korbut, Yurii Dziurakh, Yustyna Zhylishchych
Abstract Promising method for disposal the pine wood waste through extrusion pelleting using sulphate soap as a natural binder is considered in the article. Prior to pelleting, the wood waste requires drying to a water content of no more than 10%. Analysis of pine wood waste drying in filtration mode yielded optimal parameters: a 20 mm layer thickness, temperature of 135 °C, and drying time of 3,900 s. The optimal content of sulphate soap binder was determined to be about 20%, resulting in reduced coke residue, increased volatile components, higher calorific value, and enhanced static strength. This binder facilitates formation of pellets at lower pressures, increases calorific value, and acts as a lubricant, reducing friction and associated energy costs.
{"title":"Disposal of pine wood waste by pelleting with sulphate soap binder","authors":"Myroslav Malovanyy, Roman Paraniak, Ivan Tymchuk, Volodymyr Zhuk, Iryna Ablieieva, Mariia Korbut, Yurii Dziurakh, Yustyna Zhylishchych","doi":"10.1556/606.2023.00885","DOIUrl":"https://doi.org/10.1556/606.2023.00885","url":null,"abstract":"Abstract Promising method for disposal the pine wood waste through extrusion pelleting using sulphate soap as a natural binder is considered in the article. Prior to pelleting, the wood waste requires drying to a water content of no more than 10%. Analysis of pine wood waste drying in filtration mode yielded optimal parameters: a 20 mm layer thickness, temperature of 135 °C, and drying time of 3,900 s. The optimal content of sulphate soap binder was determined to be about 20%, resulting in reduced coke residue, increased volatile components, higher calorific value, and enhanced static strength. This binder facilitates formation of pellets at lower pressures, increases calorific value, and acts as a lubricant, reducing friction and associated energy costs.","PeriodicalId":35003,"journal":{"name":"Pollack Periodica","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2023-10-04","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"135591963","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}