Pub Date : 2022-05-22DOI: 10.3390/acoustics4020028
Manish Kumar, T. Abhayapala, P. Samarasinghe
The recent advances in Human-Computer Interaction and Artificial Intelligence have significantly increased the importance of identifying human emotions from different sensory cues. Hence, understanding the underlying relationships between emotions and sensory cues have become a subject of study in many fields including Acoustics, Psychology, Psychiatry, Neuroscience and Biochemistry. This work is a preliminary step towards investigating cues for human emotion on a fundamental level by aiming to establish relationships between tonal frequencies of sound and emotions. For that, an online perception test is conducted, in which participants are asked to rate the perceived emotions corresponding to each tone. The results show that a crossover point for four primary emotions lies in the frequency range of 417–440 Hz, thus consolidating the hypothesis that the frequency range of 432–440 Hz is neutral from human emotion perspective. It is also observed that the frequency dependant relationships between emotion pairs Happy—Sad, and Anger—Calm are approximately mirrored symmetric in nature.
{"title":"A Preliminary Investigation on Frequency Dependant Cues for Human Emotions","authors":"Manish Kumar, T. Abhayapala, P. Samarasinghe","doi":"10.3390/acoustics4020028","DOIUrl":"https://doi.org/10.3390/acoustics4020028","url":null,"abstract":"The recent advances in Human-Computer Interaction and Artificial Intelligence have significantly increased the importance of identifying human emotions from different sensory cues. Hence, understanding the underlying relationships between emotions and sensory cues have become a subject of study in many fields including Acoustics, Psychology, Psychiatry, Neuroscience and Biochemistry. This work is a preliminary step towards investigating cues for human emotion on a fundamental level by aiming to establish relationships between tonal frequencies of sound and emotions. For that, an online perception test is conducted, in which participants are asked to rate the perceived emotions corresponding to each tone. The results show that a crossover point for four primary emotions lies in the frequency range of 417–440 Hz, thus consolidating the hypothesis that the frequency range of 432–440 Hz is neutral from human emotion perspective. It is also observed that the frequency dependant relationships between emotion pairs Happy—Sad, and Anger—Calm are approximately mirrored symmetric in nature.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-05-22","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49107890","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-05-22DOI: 10.3390/acoustics4020029
M. Mironov
In this paper, the propagation of sound in an acoustically narrow waveguide, the wall of which is lined with identical dipole resonators and masses on springs, is theoretically considered. It is shown that, in the frequency range above the resonant frequency of the resonators, sound waves exponentially attenuate, and the waveguide is locked. The width of this range depends on two parameters—the ratio of the cross-sectional areas of the resonators and the waveguide and the ratio of the mass of the resonator to the mass of the medium displaced by it. As the resonator mass decreases, the locking band width expands and may become infinite.
{"title":"The Dipole Resonator and Dipole Waveguide Insulator in Dense Liquid Medium","authors":"M. Mironov","doi":"10.3390/acoustics4020029","DOIUrl":"https://doi.org/10.3390/acoustics4020029","url":null,"abstract":"In this paper, the propagation of sound in an acoustically narrow waveguide, the wall of which is lined with identical dipole resonators and masses on springs, is theoretically considered. It is shown that, in the frequency range above the resonant frequency of the resonators, sound waves exponentially attenuate, and the waveguide is locked. The width of this range depends on two parameters—the ratio of the cross-sectional areas of the resonators and the waveguide and the ratio of the mass of the resonator to the mass of the medium displaced by it. As the resonator mass decreases, the locking band width expands and may become infinite.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-05-22","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46598955","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-05-16DOI: 10.3390/acoustics4020026
Ali Haider Adeeb, Zühre Sü Gül
This study investigates the indoor acoustical characteristics of a Middle Byzantine masonry church in Cappadocia. The Bell Church is in partial ruins; therefore, archival data and the church’s remains are used for its acoustical reconstruction. The study aims to formulate a methodology for a realistic simulation of the church by testing the applicability of different approaches, including field and laboratory tests. By conducting qualitative and quantitative material tests, different tuff stone samples are examined from the region. Impedance tube tests are performed on the samples from Göreme and Ürgüp to document their sound absorption performances. Previous field tests on two sites in Cappadocia are also used to compare the sound absorption performance of tuff stones, supported by acoustical simulations. The texture, physical and chemical characteristics of the stones together with the measured sound absorption coefficient values are comparatively evaluated for selecting the most suitable material to be applied in the Bell Church simulations. The church was constructed in phases and underwent architectural modifications and additions over time. The indoor acoustical environment of the church is analyzed over objective acoustical parameters of EDT, T30, C50, C80, D50, and STI for its different phases with different architectural features and functional patterns.
{"title":"Investigation of a Tuff Stone Church in Cappadocia via Acoustical Reconstruction","authors":"Ali Haider Adeeb, Zühre Sü Gül","doi":"10.3390/acoustics4020026","DOIUrl":"https://doi.org/10.3390/acoustics4020026","url":null,"abstract":"This study investigates the indoor acoustical characteristics of a Middle Byzantine masonry church in Cappadocia. The Bell Church is in partial ruins; therefore, archival data and the church’s remains are used for its acoustical reconstruction. The study aims to formulate a methodology for a realistic simulation of the church by testing the applicability of different approaches, including field and laboratory tests. By conducting qualitative and quantitative material tests, different tuff stone samples are examined from the region. Impedance tube tests are performed on the samples from Göreme and Ürgüp to document their sound absorption performances. Previous field tests on two sites in Cappadocia are also used to compare the sound absorption performance of tuff stones, supported by acoustical simulations. The texture, physical and chemical characteristics of the stones together with the measured sound absorption coefficient values are comparatively evaluated for selecting the most suitable material to be applied in the Bell Church simulations. The church was constructed in phases and underwent architectural modifications and additions over time. The indoor acoustical environment of the church is analyzed over objective acoustical parameters of EDT, T30, C50, C80, D50, and STI for its different phases with different architectural features and functional patterns.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-05-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46879828","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-05-03DOI: 10.3390/acoustics4020025
A. Karki, Junru Wu
The relationship between ultrasonic parameters (attenuation coefficients and velocity) and bone porosity in bovine cancellous bone is explored to understand the possibility of fracture risk diagnosis associated with osteoporosis by applying ultrasound. In vitro measurements of ultrasonic parameters on twenty-one bovine cancellous bone samples from tibia were conducted, using ultrasonic spectroscopy in the through-transmission mode. Transducers of three different center frequencies were used to cover a wide diagnostic frequency range between 1.0–7.8 MHz. The nonlinear relationship of porosity and normalized attenuation coefficient (nATTN) and normalized broadband attenuation coefficient (nBUA) were well described by a third-order polynomial fit, whereas porosity and the phase velocity (UV) were found to be negatively correlated with the linear correlation coefficients of −0.93, −0.89 and −0.83 at 2.25, 5.00 and 7.50 MHz, respectively. The results imply that the ultrasound parameters attain maximum values for the bone sample with the lowest porosity, and then decrease for samples with greater porosity for the range of porosities in our samples for all frequencies. Spatial variation in the ultrasound parameters was found to be caused by non-uniform pore size distribution, which was examined at five different locations within the same bone specimen. However, it did not affect the relationship of ultrasound parameters and porosity at these frequencies.
{"title":"Measurement of Ultrasound Parameters of Bovine Cancellous Bone as a Function of Frequency for a Range of Porosities via Through-Transmission Ultrasonic Spectroscopy","authors":"A. Karki, Junru Wu","doi":"10.3390/acoustics4020025","DOIUrl":"https://doi.org/10.3390/acoustics4020025","url":null,"abstract":"The relationship between ultrasonic parameters (attenuation coefficients and velocity) and bone porosity in bovine cancellous bone is explored to understand the possibility of fracture risk diagnosis associated with osteoporosis by applying ultrasound. In vitro measurements of ultrasonic parameters on twenty-one bovine cancellous bone samples from tibia were conducted, using ultrasonic spectroscopy in the through-transmission mode. Transducers of three different center frequencies were used to cover a wide diagnostic frequency range between 1.0–7.8 MHz. The nonlinear relationship of porosity and normalized attenuation coefficient (nATTN) and normalized broadband attenuation coefficient (nBUA) were well described by a third-order polynomial fit, whereas porosity and the phase velocity (UV) were found to be negatively correlated with the linear correlation coefficients of −0.93, −0.89 and −0.83 at 2.25, 5.00 and 7.50 MHz, respectively. The results imply that the ultrasound parameters attain maximum values for the bone sample with the lowest porosity, and then decrease for samples with greater porosity for the range of porosities in our samples for all frequencies. Spatial variation in the ultrasound parameters was found to be caused by non-uniform pore size distribution, which was examined at five different locations within the same bone specimen. However, it did not affect the relationship of ultrasound parameters and porosity at these frequencies.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-05-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"48924525","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-04-13DOI: 10.3390/acoustics4020024
Milan Brankovic, M. Everett
Forward modeling plays a key role in both the creation of predictive models and the study of the surrounding environment through inversion methods. Due to their competitive computational cost and modest algorithmic complexity, finite difference methods (FDM) are commonly used to model the acoustic wave equation. An algorithm has been developed to decrease the computational cost of acoustic-wave forward modeling that can be applied to most finite difference methods. An important feature of the algorithm is the calculation, at each time step, of the pressure in only a moving subdomain which contains the grid points across which waves are passing. The computation is skipped at grid points at which the waves are negligibly small or non-existent. The novelty in this work comes from flexibility of the subdomain and its ability to closely follow the developing wavefield. To demonstrate the efficacy of the algorithm, it is applied to a standard finite difference scheme and validated against 2-D modeling results. The algorithm herein can play an important role in the reduction in computation time of seismic data analysis as the volumes of seismic data increase due to developments in data acquisition technology.
{"title":"A Method for Modeling Acoustic Waves in Moving Subdomains","authors":"Milan Brankovic, M. Everett","doi":"10.3390/acoustics4020024","DOIUrl":"https://doi.org/10.3390/acoustics4020024","url":null,"abstract":"Forward modeling plays a key role in both the creation of predictive models and the study of the surrounding environment through inversion methods. Due to their competitive computational cost and modest algorithmic complexity, finite difference methods (FDM) are commonly used to model the acoustic wave equation. An algorithm has been developed to decrease the computational cost of acoustic-wave forward modeling that can be applied to most finite difference methods. An important feature of the algorithm is the calculation, at each time step, of the pressure in only a moving subdomain which contains the grid points across which waves are passing. The computation is skipped at grid points at which the waves are negligibly small or non-existent. The novelty in this work comes from flexibility of the subdomain and its ability to closely follow the developing wavefield. To demonstrate the efficacy of the algorithm, it is applied to a standard finite difference scheme and validated against 2-D modeling results. The algorithm herein can play an important role in the reduction in computation time of seismic data analysis as the volumes of seismic data increase due to developments in data acquisition technology.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-13","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47235219","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-04-11DOI: 10.3390/acoustics4020022
Callum Daniels, N. Perera
Due to the nature of their deployment, very few people know the location and course of a submarine during its time at sea, including only a handful of the ship’s crew. The possibility of immediate retaliation by the UK and her allies is aided by the submarine’s ability to remain undetected by SONAR at all times. To investigate one method for improving acoustic stealth, a finite element model (FEM) was created on ANSYS to model a unit-cell of an Alberich coating and impeding sound wave representative of SONAR. A simplification of a widely used acoustic impedance equation was adopted into MATLAB code to attain values of impedance that were applied to the model in place of a water loading boundary. Using the results given by five sets of simulations, an optimised Alberich coating was modelled, containing a 26 mm spherical cavity, 40 mm anechoic layer and 30 mm long steel backplate. This optimised model improved the acoustic stealth of submarines by displaying greater acoustic absorption at both ends of the frequency range, compared with other models used, showing that Alberich-style coatings can be used to improve acoustic stealth, to combat new low-frequency SONAR.
{"title":"Investigation of Alberich Coating to Optimise Acoustic Stealth of Submarines","authors":"Callum Daniels, N. Perera","doi":"10.3390/acoustics4020022","DOIUrl":"https://doi.org/10.3390/acoustics4020022","url":null,"abstract":"Due to the nature of their deployment, very few people know the location and course of a submarine during its time at sea, including only a handful of the ship’s crew. The possibility of immediate retaliation by the UK and her allies is aided by the submarine’s ability to remain undetected by SONAR at all times. To investigate one method for improving acoustic stealth, a finite element model (FEM) was created on ANSYS to model a unit-cell of an Alberich coating and impeding sound wave representative of SONAR. A simplification of a widely used acoustic impedance equation was adopted into MATLAB code to attain values of impedance that were applied to the model in place of a water loading boundary. Using the results given by five sets of simulations, an optimised Alberich coating was modelled, containing a 26 mm spherical cavity, 40 mm anechoic layer and 30 mm long steel backplate. This optimised model improved the acoustic stealth of submarines by displaying greater acoustic absorption at both ends of the frequency range, compared with other models used, showing that Alberich-style coatings can be used to improve acoustic stealth, to combat new low-frequency SONAR.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-11","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49441776","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-04-11DOI: 10.3390/acoustics4020023
V. Palchikovskiy, I. Khramtsov, O. Kustov
This article considers the influence of the orifice arrangement in a cover of a cylindrical resonator on the impedance determined by the Dean’s method. A resonator with a small height and a low perforation degree is studied. This geometry provides different non-uniformity of the sound field at the resonator backing depending on the orifice arrangement in the resonator cover, while the number of orifices does not change. It is shown that, with different orifice arrangements, the impedance values determined by Dean’s method at high frequencies (3000 Hz and more) differ greatly. The authors propose the modification of Dean’s formula by using the amplitude coefficient of the zeroth order mode instead of the acoustic pressure at the resonator backing. The computations performed demonstrate that, in this case, the impedance does not depend on the orifice arrangement in the resonator cover. The computations consist of three stages: numerical simulation of the plane wave incidence onto the resonator (simulating a full-scale experiment); carrying out a modal analysis of the sound field at the resonator backing to extract the zeroth order mode; and determination of the resonator impedance according to the modified Dean’s formula.
{"title":"On the Influence of Certain Geometric Characteristics of the Resonator on the Impedance Determined by the Dean’s Method","authors":"V. Palchikovskiy, I. Khramtsov, O. Kustov","doi":"10.3390/acoustics4020023","DOIUrl":"https://doi.org/10.3390/acoustics4020023","url":null,"abstract":"This article considers the influence of the orifice arrangement in a cover of a cylindrical resonator on the impedance determined by the Dean’s method. A resonator with a small height and a low perforation degree is studied. This geometry provides different non-uniformity of the sound field at the resonator backing depending on the orifice arrangement in the resonator cover, while the number of orifices does not change. It is shown that, with different orifice arrangements, the impedance values determined by Dean’s method at high frequencies (3000 Hz and more) differ greatly. The authors propose the modification of Dean’s formula by using the amplitude coefficient of the zeroth order mode instead of the acoustic pressure at the resonator backing. The computations performed demonstrate that, in this case, the impedance does not depend on the orifice arrangement in the resonator cover. The computations consist of three stages: numerical simulation of the plane wave incidence onto the resonator (simulating a full-scale experiment); carrying out a modal analysis of the sound field at the resonator backing to extract the zeroth order mode; and determination of the resonator impedance according to the modified Dean’s formula.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-11","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43335533","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-04-01DOI: 10.3390/acoustics4020020
Daniel Deery, L. Flanagan, Gordon O’Brien, H. Rice, J. Kennedy
Significant potential for acoustic metamaterials to provide a breakthrough in sound attenuation has been unlocked in recent times due to advancements in additive manufacturing techniques. These materials allow the targeting of specific frequencies for sound attenuation. To date, acoustic metamaterials have not been demonstrated in a commercial automotive silencer for performance enhancement. A significant obstacle to the practical use of acoustic metamaterials is the need for low cost and efficient modelling strategies in the design phase. This study investigates the effect of acoustic metamaterials within a representative automotive silencer. The acoustic metamaterial design is achieved using a combination of analytical and finite element models, validated by experiment. The acoustic metamaterial is then compared with commonly used techniques in the silencer industry to gauge the effectiveness of the acoustic metamaterials. COMSOL simulations were used to validate the developed test rig and were compared to experimental results which were obtained using the two-load transmission loss test method. Through this testing method, the implementation of a labyrinthine metamaterial cylinder proved to be a significant improvement in transmission loss within the silencer, with an increase in transmission loss of 40 dB at 1500 Hz. The research has successfully shown that acoustic metamaterials can be used in practical settings, such as an automotive silencer, to improve the overall sound attenuating performance. The described analytical model demonstrates the potential for industrially relevant low cost design tools.
{"title":"Efficient Modelling of Acoustic Metamaterials for the Performance Enhancement of an Automotive Silencer","authors":"Daniel Deery, L. Flanagan, Gordon O’Brien, H. Rice, J. Kennedy","doi":"10.3390/acoustics4020020","DOIUrl":"https://doi.org/10.3390/acoustics4020020","url":null,"abstract":"Significant potential for acoustic metamaterials to provide a breakthrough in sound attenuation has been unlocked in recent times due to advancements in additive manufacturing techniques. These materials allow the targeting of specific frequencies for sound attenuation. To date, acoustic metamaterials have not been demonstrated in a commercial automotive silencer for performance enhancement. A significant obstacle to the practical use of acoustic metamaterials is the need for low cost and efficient modelling strategies in the design phase. This study investigates the effect of acoustic metamaterials within a representative automotive silencer. The acoustic metamaterial design is achieved using a combination of analytical and finite element models, validated by experiment. The acoustic metamaterial is then compared with commonly used techniques in the silencer industry to gauge the effectiveness of the acoustic metamaterials. COMSOL simulations were used to validate the developed test rig and were compared to experimental results which were obtained using the two-load transmission loss test method. Through this testing method, the implementation of a labyrinthine metamaterial cylinder proved to be a significant improvement in transmission loss within the silencer, with an increase in transmission loss of 40 dB at 1500 Hz. The research has successfully shown that acoustic metamaterials can be used in practical settings, such as an automotive silencer, to improve the overall sound attenuating performance. The described analytical model demonstrates the potential for industrially relevant low cost design tools.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"41712620","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-04-01DOI: 10.3390/acoustics4020019
Yaoqing Lu, Kangfu Liu, Tao Wu
The micro-electro-mechanical systems (MEMS) resonant scanners are in great demand for numerous light scanning applications. Recently, the development of LiDAR in micro-robotics and mobile devices has led to the requirement of ultra-small systems with low driving voltage, low power, compact size and high performance. We have first proposed the dual-axis MEMS scanner using the lithium niobate (LN) thin-film platform, which is expected to fulfill the requirement. This paper describes the actuation principle and scanner structure, meanwhile develops the analytical model for the scanner. The analytical model is later validated by the finite element analysis. The performance of the proposed scanner is improved with the optimization of the orientation of LN and layer thickness. The proposed scanner achieves the θopt·D·f up to 937.8∘·mm·kHz in simulation. The simulated optical angle in the x-axis and y-axis are 50∘ and 42∘ at 1 V, corresponding to resonant frequencies of 79.9 kHz and 558.2 kHz, respectively. With the superior performance of large deflection, high scanning frequency, high figure of merit and low voltage, the proposed MEMS scanner is a promising candidate for fast scanner applications (e.g., wavelength-selective switches and submicron biomedical system), especially the application of LiDAR in mobile devices or micro-robotics.
{"title":"Dual-Axis MEMS Resonant Scanner Using 128∘Y Lithium Niobate Thin-Film","authors":"Yaoqing Lu, Kangfu Liu, Tao Wu","doi":"10.3390/acoustics4020019","DOIUrl":"https://doi.org/10.3390/acoustics4020019","url":null,"abstract":"The micro-electro-mechanical systems (MEMS) resonant scanners are in great demand for numerous light scanning applications. Recently, the development of LiDAR in micro-robotics and mobile devices has led to the requirement of ultra-small systems with low driving voltage, low power, compact size and high performance. We have first proposed the dual-axis MEMS scanner using the lithium niobate (LN) thin-film platform, which is expected to fulfill the requirement. This paper describes the actuation principle and scanner structure, meanwhile develops the analytical model for the scanner. The analytical model is later validated by the finite element analysis. The performance of the proposed scanner is improved with the optimization of the orientation of LN and layer thickness. The proposed scanner achieves the θopt·D·f up to 937.8∘·mm·kHz in simulation. The simulated optical angle in the x-axis and y-axis are 50∘ and 42∘ at 1 V, corresponding to resonant frequencies of 79.9 kHz and 558.2 kHz, respectively. With the superior performance of large deflection, high scanning frequency, high figure of merit and low voltage, the proposed MEMS scanner is a promising candidate for fast scanner applications (e.g., wavelength-selective switches and submicron biomedical system), especially the application of LiDAR in mobile devices or micro-robotics.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49499090","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-03-18DOI: 10.3390/acoustics4010017
E. Nilsson, Sylvain Ménard, Delphine Bard Hagberg, N. Vardaxis
Sound reduction is complex to estimate for acoustical treatments on ventilation ducts through walls. Various acoustical treatments are available for ventilation ducts, including internal lining (absorption along the inner perimeter), external lagging (external sound insulation), silencer, and suspended ceilings. Previous studies have examined how silencers and the internal lining affect the sound transmission of ventilation ducts. However, there are few theories to predict the effect of external lagging in combination with ventilation ducts and how the total sound reduction is affected. This article aims to investigate different acoustical treatments and develop theoretical models when external lagging with stone wool is used to reduce flanking sound transmission via the surface area of ventilation ducts. Theoretical models are developed for external lagging and compared with measurement data. Measurements and theory are generally in good agreement over the third-octave band range of 100–5000 Hz. The developed models clarify that the distance closest to the wall has the main impact on sound reduction for a combined system with a wall and a ventilation duct. Suspended ceilings and silencers are found to be enough as acoustical treatments for certain combinations of ventilation ducts and walls. However, external lagging seems to be the only effective solution in offices and schools when a large ventilation duct passes through a wall with high sound reduction.
{"title":"Acoustical Treatments on Ventilation Ducts through Walls: Experimental Results and Novel Models","authors":"E. Nilsson, Sylvain Ménard, Delphine Bard Hagberg, N. Vardaxis","doi":"10.3390/acoustics4010017","DOIUrl":"https://doi.org/10.3390/acoustics4010017","url":null,"abstract":"Sound reduction is complex to estimate for acoustical treatments on ventilation ducts through walls. Various acoustical treatments are available for ventilation ducts, including internal lining (absorption along the inner perimeter), external lagging (external sound insulation), silencer, and suspended ceilings. Previous studies have examined how silencers and the internal lining affect the sound transmission of ventilation ducts. However, there are few theories to predict the effect of external lagging in combination with ventilation ducts and how the total sound reduction is affected. This article aims to investigate different acoustical treatments and develop theoretical models when external lagging with stone wool is used to reduce flanking sound transmission via the surface area of ventilation ducts. Theoretical models are developed for external lagging and compared with measurement data. Measurements and theory are generally in good agreement over the third-octave band range of 100–5000 Hz. The developed models clarify that the distance closest to the wall has the main impact on sound reduction for a combined system with a wall and a ventilation duct. Suspended ceilings and silencers are found to be enough as acoustical treatments for certain combinations of ventilation ducts and walls. However, external lagging seems to be the only effective solution in offices and schools when a large ventilation duct passes through a wall with high sound reduction.","PeriodicalId":72045,"journal":{"name":"Acoustics (Basel, Switzerland)","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43171427","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：