M. Azni, Atiqah Zainal Abidin, R. Noorain, Sharifah Mariam Syed Hitam, L. Ernawati, R. Abdullah, A. Shoiful, R. Mohamad
The most common method of treating palm oil mill effluent (POME) is by using various types of bacteria communities. However, the utilization of microalgae in consuming the high nutrient content in wastewater offer additional benefit, particularly for CO2 sequestration. In this study, we proposed to evaluate the performance of multicultural bacteria obtained from municipal wastewater and Chlorella sp. for batch treatment of POME at different COD concentrations (ranges between 600 to 1,300 mg/L), microalgae species (C. vulgaris and C. pyrenoidosa) and speed of agitation (0 and 150 rpm). The results showed that between the bacteria and microalgae that are involved in POME treatment, microalgae give high removal of colour (93%) and ammoniacal nitrogen (95%). As for the COD and phosphate removal, both microorganisms show comparable performances. It was observed that C. pyrenoidosa was able to remove more colour compared to C. vulgaris where higher lipid yield production was obtained (47.6%). However, there is no significant impact of agitation on pollutant removal. This study also reveals that co-cultivation of different microalgae species does not affect the efficiency of the system. This study provides an important insight into developing an efficient and environmentally friendly method to treat wastewater by incorporating green technology in the treatment system
{"title":"Performance of Chlorella sp. and Multicultural Bacteria in Removing Pollutants from Nutrient-Rich Wastewater","authors":"M. Azni, Atiqah Zainal Abidin, R. Noorain, Sharifah Mariam Syed Hitam, L. Ernawati, R. Abdullah, A. Shoiful, R. Mohamad","doi":"10.22146/ajche.69427","DOIUrl":"https://doi.org/10.22146/ajche.69427","url":null,"abstract":"The most common method of treating palm oil mill effluent (POME) is by using various types of bacteria communities. However, the utilization of microalgae in consuming the high nutrient content in wastewater offer additional benefit, particularly for CO2 sequestration. In this study, we proposed to evaluate the performance of multicultural bacteria obtained from municipal wastewater and Chlorella sp. for batch treatment of POME at different COD concentrations (ranges between 600 to 1,300 mg/L), microalgae species (C. vulgaris and C. pyrenoidosa) and speed of agitation (0 and 150 rpm). The results showed that between the bacteria and microalgae that are involved in POME treatment, microalgae give high removal of colour (93%) and ammoniacal nitrogen (95%). As for the COD and phosphate removal, both microorganisms show comparable performances. It was observed that C. pyrenoidosa was able to remove more colour compared to C. vulgaris where higher lipid yield production was obtained (47.6%). However, there is no significant impact of agitation on pollutant removal. This study also reveals that co-cultivation of different microalgae species does not affect the efficiency of the system. This study provides an important insight into developing an efficient and environmentally friendly method to treat wastewater by incorporating green technology in the treatment system","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"48396217","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. K. Wirawan, D. Timotius, Ivone Marselina Nugraha, Asdi Restana, Afrizal Luthfi Anggara, Sayoga Hidayatullah
Crude Palm Oil (CPO) is obtained from palm fruit extraction. Free Fatty Acid (FFA) level is one of the most important parameters to determine the CPO quality. The standard FFA level in the industry is less than 5%. In the palm oil processing industry, FFA levels in CPO have been minimized through vacuum distillation processes. However, due to the emulsified water in oil and long departure waiting time in port, FFA levels in CPO raise to above 5% resulting in lower quality and selling price. This study has developed a novel approach to mitigate this problem by using anionic resin as an adsorbent to decrease the FFA level. We investigated the kinetics and equilibrium behavior of FFA adsorption in CPO on the anionic resin. The adsorption was conducted in several resin dose (17.5%; 25%; 33.33%; 43%). The kinetic study shows that the FFA adsorption kinetics on anionic resin follows the Pseudo-second-order rate model with the value of k2 vary between 2.1034×10-4 – 1.7375×10-3 and the qe value is in the range of 103.627 - 163.880 (mg/g). The equilibrium study shows that the Freundlich isotherm model is the fittest. The Kf values are obtained between 4.16-15.02, and the n values are in the range of 1.62-2.05. The thermodynamic observation was also involved in this study. The value of and are 28.59 kJ/mol and 91.25 J/mol/K respectively. The results show that the reaction is endothermic, spontaneous, and feasible.
{"title":"Kinetics and Adsorption Equilibrium Study of Free Fatty Acid (FFA) from Crude Palm Oil (CPO) on Anionic Resin","authors":"S. K. Wirawan, D. Timotius, Ivone Marselina Nugraha, Asdi Restana, Afrizal Luthfi Anggara, Sayoga Hidayatullah","doi":"10.22146/ajche.70319","DOIUrl":"https://doi.org/10.22146/ajche.70319","url":null,"abstract":"Crude Palm Oil (CPO) is obtained from palm fruit extraction. Free Fatty Acid (FFA) level is one of the most important parameters to determine the CPO quality. The standard FFA level in the industry is less than 5%. In the palm oil processing industry, FFA levels in CPO have been minimized through vacuum distillation processes. However, due to the emulsified water in oil and long departure waiting time in port, FFA levels in CPO raise to above 5% resulting in lower quality and selling price. This study has developed a novel approach to mitigate this problem by using anionic resin as an adsorbent to decrease the FFA level. We investigated the kinetics and equilibrium behavior of FFA adsorption in CPO on the anionic resin. The adsorption was conducted in several resin dose (17.5%; 25%; 33.33%; 43%). The kinetic study shows that the FFA adsorption kinetics on anionic resin follows the Pseudo-second-order rate model with the value of k2 vary between 2.1034×10-4 – 1.7375×10-3 and the qe value is in the range of 103.627 - 163.880 (mg/g). The equilibrium study shows that the Freundlich isotherm model is the fittest. The Kf values are obtained between 4.16-15.02, and the n values are in the range of 1.62-2.05. The thermodynamic observation was also involved in this study. The value of and are 28.59 kJ/mol and 91.25 J/mol/K respectively. The results show that the reaction is endothermic, spontaneous, and feasible.","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47937632","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Understanding the fundamental aspects of foaming properties will influence its generation and stabilization at different concentrations of the critical aggregation concentration (CAC), foam volume stability, foam height, salinity influences, and crude oil CO2-foam stability. Carbon-Dioxide based enhanced oil recovery techniques are widely employed to extract additional oil from the reservoir. The adsorption of protein at the interfaces produces extremely viscoelastic layers with high viscosity. This research aims to investigate whether whey protein isolate (WPI) is a foaming agent that can be used to improve oil recovery. WPI lowers the interfaces’ surface tension, which also has a propensity to disclose and stabilize the interface by forming a viscoelastic network and directing to high surface moduli. Comparatively, the surface tension is lowered by sodium dodecyl sulfate (SDS) surfactants than the WPI, but they do not produce a high modulus interface. WPI is demonstrated to be a greater foam stabilizer in oil and various salt conditions than SDS foam. Adding sodium chloride (NaCl) increased the half-life and volume of foam more on WPI foam compared to SDS foam. SDS foamability and foam consistency decreased dramatically at 2 wt% of NaCl concentration and above while WPI foam increased. The crude oil affected both foams, but WPI foam has not been affected as much as the SDS foam due to its high strength compared to traditional foams. The study shows that WPI reduced interfacial tension from 38 to 11 mN/m and reduced surface tension (72.3 to 48 mN/m). It was low enough and can be used as a substitute for a foaming agent to enhance the recovery of oil.
{"title":"Utilization of Whey Protein Isolate as CO2 Foam Stabilizer for Enhanced Oil Recovery","authors":"M. Said, M. Jaafar, S. Omar, Ali Mohamed Samin","doi":"10.22146/ajche.69004","DOIUrl":"https://doi.org/10.22146/ajche.69004","url":null,"abstract":"Understanding the fundamental aspects of foaming properties will influence its generation and stabilization at different concentrations of the critical aggregation concentration (CAC), foam volume stability, foam height, salinity influences, and crude oil CO2-foam stability. Carbon-Dioxide based enhanced oil recovery techniques are widely employed to extract additional oil from the reservoir. The adsorption of protein at the interfaces produces extremely viscoelastic layers with high viscosity. This research aims to investigate whether whey protein isolate (WPI) is a foaming agent that can be used to improve oil recovery. WPI lowers the interfaces’ surface tension, which also has a propensity to disclose and stabilize the interface by forming a viscoelastic network and directing to high surface moduli. Comparatively, the surface tension is lowered by sodium dodecyl sulfate (SDS) surfactants than the WPI, but they do not produce a high modulus interface. WPI is demonstrated to be a greater foam stabilizer in oil and various salt conditions than SDS foam. Adding sodium chloride (NaCl) increased the half-life and volume of foam more on WPI foam compared to SDS foam. SDS foamability and foam consistency decreased dramatically at 2 wt% of NaCl concentration and above while WPI foam increased. The crude oil affected both foams, but WPI foam has not been affected as much as the SDS foam due to its high strength compared to traditional foams. The study shows that WPI reduced interfacial tension from 38 to 11 mN/m and reduced surface tension (72.3 to 48 mN/m). It was low enough and can be used as a substitute for a foaming agent to enhance the recovery of oil.","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46675178","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
A. Halim, Afninda Aryuni Widyanti, Celvin Dicky Wahyudi, F. Martak, Eka Luthfi Septiani
High moisture content in low-range coal causes low calorific value. To increase the quality, drying by a coal dryer to minimize moisture content is proposed. Here, a case study of a cyclone-like conical tube coal dryer pilot plant was reported. Drying heating uses combustion heat generated from volatile matter combustion. This approach will solve the two problems simultaneously: decreasing moisture content and volatile matter. The computational fluid dynamic (CFD) approach is used to study fluid dynamics inside the coal dryer using ANSYS Fluent 2020R2 software. The CFD simulation results represent the phenomenon of coal drying inside the coal dryer validated by the pilot plant experimental result. The simulation was carried out in steady and unsteady conditions to understand the drying phenomena. The simulation firmly fits the experimental result, especially in an unsteady state system, indicating that the simulation result is promising for further coal dryer design. The optimal condition produces a high moisture content reduction of 86.37%, uniform fluid distribution, and significant volatile matter combustion
{"title":"A Pilot Plant Study of Coal Dryer: Simulation and Experiment","authors":"A. Halim, Afninda Aryuni Widyanti, Celvin Dicky Wahyudi, F. Martak, Eka Luthfi Septiani","doi":"10.22146/ajche.68745","DOIUrl":"https://doi.org/10.22146/ajche.68745","url":null,"abstract":"High moisture content in low-range coal causes low calorific value. To increase the quality, drying by a coal dryer to minimize moisture content is proposed. Here, a case study of a cyclone-like conical tube coal dryer pilot plant was reported. Drying heating uses combustion heat generated from volatile matter combustion. This approach will solve the two problems simultaneously: decreasing moisture content and volatile matter. The computational fluid dynamic (CFD) approach is used to study fluid dynamics inside the coal dryer using ANSYS Fluent 2020R2 software. The CFD simulation results represent the phenomenon of coal drying inside the coal dryer validated by the pilot plant experimental result. The simulation was carried out in steady and unsteady conditions to understand the drying phenomena. The simulation firmly fits the experimental result, especially in an unsteady state system, indicating that the simulation result is promising for further coal dryer design. The optimal condition produces a high moisture content reduction of 86.37%, uniform fluid distribution, and significant volatile matter combustion","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42852456","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Puspitasari, A. Cifriadi, A. Ramadhan, M. Chalid
Cushion gum is a type of rubber composite material used as adhesive in the manufacture of retread tires. Therefore, cushion gum should have good processability and mechanical characteristics, particularly tensile property, and adhesion strength. The effect of hybrid filler and curing system on the performance of green cushion gum composite was investigated to determine the appropriate green cushion gum formula designed at a laboratory scale. The content of CB N330/lignin in hybrid filler was arranged at 40/10 phr and 50/10 phr. Meanwhile, the curing system was performed semi-efficient (CBS/S 1.6/1.6 phr) and conventional (CBS/S 1.6/2.2 phr). Green cushion gum composite was also formulated using pine tar oil as a bio plasticizer. Referred to the curing characteristic and mechanical property test result, it showed that green cushion gum composite formula coded by RF1 which composed of CB N330/lignin as 50/10 phr and applied conventional curing system which ratio of CBS/S as 1.6/2.2 phr was regarded as the acceptable combination in designing green cushion gum composite formula. Higher CB N330 loading in hybrid filler composition and conventional curing system attributed to the relatively high crosslink density indicated by MH-ML value. Consequently, green cushion gum composite was obtained using the RF1 formula that has a better optimum curing time accompanied by good tensile property and adhesion strength. The composite was also comparable to conventional commercial cushion gum.
{"title":"Performance Evaluation of Green Cushion Gum Composite Formulated Based on Hybrid Filler and Curing System","authors":"S. Puspitasari, A. Cifriadi, A. Ramadhan, M. Chalid","doi":"10.22146/ajche.69888","DOIUrl":"https://doi.org/10.22146/ajche.69888","url":null,"abstract":"Cushion gum is a type of rubber composite material used as adhesive in the manufacture of retread tires. Therefore, cushion gum should have good processability and mechanical characteristics, particularly tensile property, and adhesion strength. The effect of hybrid filler and curing system on the performance of green cushion gum composite was investigated to determine the appropriate green cushion gum formula designed at a laboratory scale. The content of CB N330/lignin in hybrid filler was arranged at 40/10 phr and 50/10 phr. Meanwhile, the curing system was performed semi-efficient (CBS/S 1.6/1.6 phr) and conventional (CBS/S 1.6/2.2 phr). Green cushion gum composite was also formulated using pine tar oil as a bio plasticizer. Referred to the curing characteristic and mechanical property test result, it showed that green cushion gum composite formula coded by RF1 which composed of CB N330/lignin as 50/10 phr and applied conventional curing system which ratio of CBS/S as 1.6/2.2 phr was regarded as the acceptable combination in designing green cushion gum composite formula. Higher CB N330 loading in hybrid filler composition and conventional curing system attributed to the relatively high crosslink density indicated by MH-ML value. Consequently, green cushion gum composite was obtained using the RF1 formula that has a better optimum curing time accompanied by good tensile property and adhesion strength. The composite was also comparable to conventional commercial cushion gum.","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49478171","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
M. Kaavessina, E. N. Shohih, S. Distantina, Fadilah Fadilah
In a specific range of electrical conductivity, poly(lactic acid)/PLA has the potential to be developed into environmentally friendly antistatic packaging after a modification process. PLA was blended in a mini single screw extruder at 180oC with different compositions of micro-graphite (0, 0.5, 1, and 1.5 %wt.). This report discusses the degradability of PLA composite, i.e., photo-oxidative degradation and hydrolytic degradation. The weight loss, thermal properties, and cross-section morphology of the tested specimens were monitored periodically. During the degradation test, micro-graphite could be released from the composite, leaving a rough surface and reducing the weight of the composite. Differential scanning calorimetry (DSC) test exhibited that the presence of micro-graphite did not influence the melting temperature of the composition studied. However, the onset temperature of the melting point showed a slight shift of about 2-4oC. Bulk crystallinity demonstrated a considerable dependence on the micro-graphite loading (0-1.5%wt). However, there were two contradictory phenomena after both degradation tests. UV exposure could stimulate the fragmentation of PLA chains, break the crystal structure and increase the embrittlement. Thus, crystallinity tended to decrease during photo-oxidative degradation. In hydrolytic degradation, degradation firstly occurred in the amorphous regions and was ongoing within the studied range of time (0-20 weeks). Thus, the bulk crystallinity of composite tended to increase.
{"title":"Photo-Oxidative Degradation and Hydrolytic Degradation of Micro-Graphite Filled Poly(lactic acid) Composites","authors":"M. Kaavessina, E. N. Shohih, S. Distantina, Fadilah Fadilah","doi":"10.22146/ajche.70871","DOIUrl":"https://doi.org/10.22146/ajche.70871","url":null,"abstract":"In a specific range of electrical conductivity, poly(lactic acid)/PLA has the potential to be developed into environmentally friendly antistatic packaging after a modification process. PLA was blended in a mini single screw extruder at 180oC with different compositions of micro-graphite (0, 0.5, 1, and 1.5 %wt.). This report discusses the degradability of PLA composite, i.e., photo-oxidative degradation and hydrolytic degradation. The weight loss, thermal properties, and cross-section morphology of the tested specimens were monitored periodically. During the degradation test, micro-graphite could be released from the composite, leaving a rough surface and reducing the weight of the composite. Differential scanning calorimetry (DSC) test exhibited that the presence of micro-graphite did not influence the melting temperature of the composition studied. However, the onset temperature of the melting point showed a slight shift of about 2-4oC. Bulk crystallinity demonstrated a considerable dependence on the micro-graphite loading (0-1.5%wt). However, there were two contradictory phenomena after both degradation tests. UV exposure could stimulate the fragmentation of PLA chains, break the crystal structure and increase the embrittlement. Thus, crystallinity tended to decrease during photo-oxidative degradation. In hydrolytic degradation, degradation firstly occurred in the amorphous regions and was ongoing within the studied range of time (0-20 weeks). Thus, the bulk crystallinity of composite tended to increase.","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47547489","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
S. Jamilatun, A. Budiman, I. Mufandi, A. Aktawan, N. Fauzi, Defiani Putri Denanti
Microalgae is the third generation of biomass as renewable energy, a future energy source for making bio-oil. The purpose of this research is to examine the biomass from microalgae Spirulina platensis residue (SPR) using the pyrolysis process, to investigate the effect of particle mesh and temperature on the pyrolysis process, to determine the bio-oil properties, including density, pH, color, flame power, and conversion. Fixed bed reactor used for SPR pyrolysis with dimensions of 4.4 cm outside diameter, 4.0 cm inside diameter, and 60.0 cm reactor height. The temperature controls have been fitted from 300-600 °C combined with a 14-16 °C/minute heating rate. Spirulina platensis residue of 50 grams with various particle mesh (80 and 140 mesh) was fed to the reactor. From the experiment results, the particle mesh and temperature process are influenced by bio-oil yield, water phase, gas yield, biochar yield, conversion, and bio-oil properties, including density, pH, flame power, and color. One hundred forty mesh particles at a temperature of 500 °C showed the highest bio-oil yield with a yield of 22.92%, then the water, charcoal, and gas phases were 27.98, 18.84, and 30.26%, with a conversion of 81.16%. At the same time, 80 mesh particles at 500 °C yielded bio-oil, water, charcoal, and gas phases of 19.66, respectively; 23.10, 27.90, and 29.34%, with a conversion of 72.10%. In addition, density, pH, color, and flame power are described in this study.
{"title":"The Effects of Particle Mesh and Temperature on Pyrolysis Spirulina platensis Residue (SPR): Pyrolysis Yield and Bio-Oil Properties","authors":"S. Jamilatun, A. Budiman, I. Mufandi, A. Aktawan, N. Fauzi, Defiani Putri Denanti","doi":"10.22146/ajche.69439","DOIUrl":"https://doi.org/10.22146/ajche.69439","url":null,"abstract":"Microalgae is the third generation of biomass as renewable energy, a future energy source for making bio-oil. The purpose of this research is to examine the biomass from microalgae Spirulina platensis residue (SPR) using the pyrolysis process, to investigate the effect of particle mesh and temperature on the pyrolysis process, to determine the bio-oil properties, including density, pH, color, flame power, and conversion. Fixed bed reactor used for SPR pyrolysis with dimensions of 4.4 cm outside diameter, 4.0 cm inside diameter, and 60.0 cm reactor height. The temperature controls have been fitted from 300-600 °C combined with a 14-16 °C/minute heating rate. Spirulina platensis residue of 50 grams with various particle mesh (80 and 140 mesh) was fed to the reactor. From the experiment results, the particle mesh and temperature process are influenced by bio-oil yield, water phase, gas yield, biochar yield, conversion, and bio-oil properties, including density, pH, flame power, and color. One hundred forty mesh particles at a temperature of 500 °C showed the highest bio-oil yield with a yield of 22.92%, then the water, charcoal, and gas phases were 27.98, 18.84, and 30.26%, with a conversion of 81.16%. At the same time, 80 mesh particles at 500 °C yielded bio-oil, water, charcoal, and gas phases of 19.66, respectively; 23.10, 27.90, and 29.34%, with a conversion of 72.10%. In addition, density, pH, color, and flame power are described in this study. ","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":"32 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"41272463","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
H. Rustamaji, T. Prakoso, H. Devianto, P. Widiatmoko, I. Nurdin
This research investigates the design, fabrication, and testing of single-cell and module supercapacitors. The supercapacitor consists of carbon nanocomposites, which contain activated carbon (AC), multiwall carbon nanotubes (MWCNT), and graphene (GR). The coin and pouch cell type supercapacitors were manufactured with AC: MWCNT: GR composite electrodes in a ratio of 70:20:10 weight percent. Meanwhile, the electrochemical characterization showed that the highest capacitance values for single coin and pouch cells were 32.13 F g-1 and 5.3 F g-1, respectively, in 6 M KOH electrolyte at a scan rate of 2 mV s-1. Furthermore, the power and energy densities for the coin-cell supercapacitor were 69 W kg-1 and 6.6 Wh kg-1, respectively, while for the pouch cell, it was 7.4 W kg-1 and 1.0 Wh kg-1, respectively. The coin-cell supercapacitor durability test was carried out for 1000 cycles, yielding the retention capacitance and coulombic efficiency values of 94-97% and 100%, respectively. These results showed that the performance of the supercapacitor is close to commercial products.
{"title":"Design, Fabrication, and Testing of Supercapacitor Based on Nanocarbon Composite Material","authors":"H. Rustamaji, T. Prakoso, H. Devianto, P. Widiatmoko, I. Nurdin","doi":"10.22146/ajche.70139","DOIUrl":"https://doi.org/10.22146/ajche.70139","url":null,"abstract":"This research investigates the design, fabrication, and testing of single-cell and module supercapacitors. The supercapacitor consists of carbon nanocomposites, which contain activated carbon (AC), multiwall carbon nanotubes (MWCNT), and graphene (GR). The coin and pouch cell type supercapacitors were manufactured with AC: MWCNT: GR composite electrodes in a ratio of 70:20:10 weight percent. Meanwhile, the electrochemical characterization showed that the highest capacitance values for single coin and pouch cells were 32.13 F g-1 and 5.3 F g-1, respectively, in 6 M KOH electrolyte at a scan rate of 2 mV s-1. Furthermore, the power and energy densities for the coin-cell supercapacitor were 69 W kg-1 and 6.6 Wh kg-1, respectively, while for the pouch cell, it was 7.4 W kg-1 and 1.0 Wh kg-1, respectively. The coin-cell supercapacitor durability test was carried out for 1000 cycles, yielding the retention capacitance and coulombic efficiency values of 94-97% and 100%, respectively. These results showed that the performance of the supercapacitor is close to commercial products. ","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42025523","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Francisca Larasati, Y. Kusumastuti, A. Mindaryani, R. Rochmadi, M. Handayani
Multi-walled carbon nanotubes (MWCNTs) are known as efficient drug carriers. To improve their interaction with other materials, surface modification of MWCNTs is necessary. In this work, MWCNTs were functionalized with acid and polysaccharides (chitosan and gelatin). The functionalization process was done via modification with acid solutions of nitric acid, sulfuric acid, and a mixture of nitric acid-sulfuric acid first, followed by functionalization with chitosan and gelatin. To achieve the optimum condition of MWCNTs functionalization, the reaction time, temperature, and acid ratio were varied. Furthermore, the effect of chitosan and gelatin addition into MWCNTs was studied at various mass ratios. The synthesized materials were characterized by Fourier transform infrared spectrophotometer, Boehm titration, and dispersion test. The Boehm titration results showed that the acid functional groups had been attached successfully to MWCNTs surface. The amount of acid functional groups increased along with reaction time. The highest amount of acidic group obtained from the data was 2.33 mmol/g. It was achieved when MWCNTs reacted with nitric acid for 24 hours. Temperature and acid ratio variations on the MWCNTs functionalization did not provide significant results. From the FTIR data, sharp peaks at 3480 cm-1 and 1040 cm-1 indicates a -CONH bond, which shows that chitosan and gelatin have been successfully grafted onto MWCNTs surface via an amide linkage. Moreover, the dispersion test showed that the functionalized materials were stable for 48 hours.
{"title":"Surface Modification of Multi-Walled Carbon Nanotubes with Polysaccharides","authors":"Francisca Larasati, Y. Kusumastuti, A. Mindaryani, R. Rochmadi, M. Handayani","doi":"10.22146/ajche.69866","DOIUrl":"https://doi.org/10.22146/ajche.69866","url":null,"abstract":"Multi-walled carbon nanotubes (MWCNTs) are known as efficient drug carriers. To improve their interaction with other materials, surface modification of MWCNTs is necessary. In this work, MWCNTs were functionalized with acid and polysaccharides (chitosan and gelatin). The functionalization process was done via modification with acid solutions of nitric acid, sulfuric acid, and a mixture of nitric acid-sulfuric acid first, followed by functionalization with chitosan and gelatin. To achieve the optimum condition of MWCNTs functionalization, the reaction time, temperature, and acid ratio were varied. Furthermore, the effect of chitosan and gelatin addition into MWCNTs was studied at various mass ratios. The synthesized materials were characterized by Fourier transform infrared spectrophotometer, Boehm titration, and dispersion test. The Boehm titration results showed that the acid functional groups had been attached successfully to MWCNTs surface. The amount of acid functional groups increased along with reaction time. The highest amount of acidic group obtained from the data was 2.33 mmol/g. It was achieved when MWCNTs reacted with nitric acid for 24 hours. Temperature and acid ratio variations on the MWCNTs functionalization did not provide significant results. From the FTIR data, sharp peaks at 3480 cm-1 and 1040 cm-1 indicates a -CONH bond, which shows that chitosan and gelatin have been successfully grafted onto MWCNTs surface via an amide linkage. Moreover, the dispersion test showed that the functionalized materials were stable for 48 hours.","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42772747","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
R. M. T. Cumba, Clark B. Ligalig, Jhea Mae D. Tingson, Meralin P. Molina, A. Alguno, C. Deocaris, Felmer S. Latayada, I. Primadona, R. Capangpangan
Organic dyes used in the food and textile industries are the primary sources of environmental contamination due to their high toxicity and nonbiodegradability. This paper describes the synthesis of cellulose nanocrystals/zinc oxide (CNC/ZnO) nanocomposite via the sol-gel method. Various characterization techniques such as FTIR spectroscopy, UV-Vis spectroscopy, and FESEM-EDX analysis were done. FTIR and UV-Vis analyses initially confirmed the formation of CNC/ZnO nanocomposites. FESEM-EDX showed a fiber-like structure with agglomerated particles on the CNC-ZnO image, suggesting the functionalization of ZnO nanoparticles onto the CNC. The photocatalytic potential of the CNC/ZnO nanocomposite was then evaluated by degrading 10 ppm thiazine dye (methylene blue) solution. The solution was irradiated with UV and visible light at an ambient temperature. The degradation was monitored at different time intervals using a UV spectrophotometer to measure the absorbance value intermittently. Results on the photocatalytic activity indicated that the synthesized CNC/ZnO nanocomposite showed faster degradation under UV light irradiation than the visible light, with an efficiency of 96.11% and 85.60%, respectively, after 180 mins of light irradiation. Further, the results suggest that the synthesized CNC/ZnO nanocomposite showed great promise as a sustainable material for the degradation of organic contaminants in an aqueous solution.
{"title":"Photocatalytic Activity of Cellulose Nanocrystals/Zinc Oxide Nanocomposite Against Thiazine Dye under UV and Visible Light Irradiation","authors":"R. M. T. Cumba, Clark B. Ligalig, Jhea Mae D. Tingson, Meralin P. Molina, A. Alguno, C. Deocaris, Felmer S. Latayada, I. Primadona, R. Capangpangan","doi":"10.22146/ajche.72331","DOIUrl":"https://doi.org/10.22146/ajche.72331","url":null,"abstract":"Organic dyes used in the food and textile industries are the primary sources of environmental contamination due to their high toxicity and nonbiodegradability. This paper describes the synthesis of cellulose nanocrystals/zinc oxide (CNC/ZnO) nanocomposite via the sol-gel method. Various characterization techniques such as FTIR spectroscopy, UV-Vis spectroscopy, and FESEM-EDX analysis were done. FTIR and UV-Vis analyses initially confirmed the formation of CNC/ZnO nanocomposites. FESEM-EDX showed a fiber-like structure with agglomerated particles on the CNC-ZnO image, suggesting the functionalization of ZnO nanoparticles onto the CNC. The photocatalytic potential of the CNC/ZnO nanocomposite was then evaluated by degrading 10 ppm thiazine dye (methylene blue) solution. The solution was irradiated with UV and visible light at an ambient temperature. The degradation was monitored at different time intervals using a UV spectrophotometer to measure the absorbance value intermittently. Results on the photocatalytic activity indicated that the synthesized CNC/ZnO nanocomposite showed faster degradation under UV light irradiation than the visible light, with an efficiency of 96.11% and 85.60%, respectively, after 180 mins of light irradiation. Further, the results suggest that the synthesized CNC/ZnO nanocomposite showed great promise as a sustainable material for the degradation of organic contaminants in an aqueous solution.","PeriodicalId":8490,"journal":{"name":"ASEAN Journal of Chemical Engineering","volume":" ","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-06-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43738665","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：