Pub Date : 2022-01-01DOI: 10.5658/wood.2022.50.1.1
In-Hwan Lee, Keon-Ho Kim, K. Shim
To evaluate the bearing strength of red pine cross-laminated timber (CLT) with self-tapping screw (STS), which is widely used as a fastener for connection in CLT building, the bearing test was conducted. Accoring to the STS’s diameters (8, 10, 12 mm), the bearing test specimens with half hole were manufactured. Bearing strength was compared and reviewed in consideration of the configuration in STS and the loading direction to the grain of red pine. As a result of the bearing test on the STS’s diameter, the yield bearing load increases as the larger diameter of the STS in all directions of the red pine. The bearing strength of the thread part (thread + tip) was higher than the shank part (shank + shank cutter). In compared with the directions to the grain of red pine, the bearing strength of the cross section parallel to the loading direction was the highest, and the tangent section was the lowest bearing strength. The average bearing strength of the loading direction in parallel to the grain was 23.43 MPa, which was about 45% higher than the average 16.16 MPa in perpendicular to the grain. The predicted bearing strength calculated by Eurocode (EN) and Korean Building Code (KBC)’s equation was lower than the experimental value. It is nessesary to propose the new equations of bearing strength reflected the configuration information of STS.
{"title":"Evaluation of Bearing Strength of Self-Tapping Screws according to the Grain Direction of Domestic Pinus densiflora","authors":"In-Hwan Lee, Keon-Ho Kim, K. Shim","doi":"10.5658/wood.2022.50.1.1","DOIUrl":"https://doi.org/10.5658/wood.2022.50.1.1","url":null,"abstract":"To evaluate the bearing strength of red pine cross-laminated timber (CLT) with self-tapping screw (STS), which is widely used as a fastener for connection in CLT building, the bearing test was conducted. Accoring to the STS’s diameters (8, 10, 12 mm), the bearing test specimens with half hole were manufactured. Bearing strength was compared and reviewed in consideration of the configuration in STS and the loading direction to the grain of red pine. As a result of the bearing test on the STS’s diameter, the yield bearing load increases as the larger diameter of the STS in all directions of the red pine. The bearing strength of the thread part (thread + tip) was higher than the shank part (shank + shank cutter). In compared with the directions to the grain of red pine, the bearing strength of the cross section parallel to the loading direction was the highest, and the tangent section was the lowest bearing strength. The average bearing strength of the loading direction in parallel to the grain was 23.43 MPa, which was about 45% higher than the average 16.16 MPa in perpendicular to the grain. The predicted bearing strength calculated by Eurocode (EN) and Korean Building Code (KBC)’s equation was lower than the experimental value. It is nessesary to propose the new equations of bearing strength reflected the configuration information of STS.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2022-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43247830","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-01-01DOI: 10.5658/wood.2022.50.1.12
Hyunjeong Na, Tae-Jong Kim
Many studies on plant extracts have been reported for the treatment of candidiasis caused by Candida albicans, a representative fungal infection. This study demonstrates the synergistic antifungal activity of the combination of Phellodendri Cortex and Magnoliae Cortex, previously reported to have antifungal efficacy. Considering the antifungal efficacy and the separation of the active constituents, berberine and magnolol, hot water extraction and carbon dioxide supercritical extraction were selected for Phellodendri Cortex and Magnoliae Cortex, respectively. A combination of 0.55 g/L hot water extract of Phellodendri Cortex and 0.59 g/L carbon dioxide supercritical extract of Magnoliae Cortex showed synergistic antifungal activity. The synergistic antifungal activity of 160 μM berberine and 100 μM magnolol, which are representative antifungal compounds of Phellodendri Cortex and Magnoliae Cortex, respectively, contributes to the synergistic antifungal effect of their extracts. The additive decrease in cellular ergosterol level and the increased antifungal efficacy by extracellular ergosterol suggest that disruption of the biological function of ergosterol in the cell membrane is not responsible for the synergistic antifungal activity of berberine and magnolol. Synergistic cellular release of chromosomal DNA upon mixing berberine and magnolol indicates that disruption of the cellular structure is responsible for the synergistic antifungal effect of berberine and magnolol.
{"title":"Synergistic Antifungal Activity of Phellodendri Cortex and Magnoliae Cortex against Candida albicans","authors":"Hyunjeong Na, Tae-Jong Kim","doi":"10.5658/wood.2022.50.1.12","DOIUrl":"https://doi.org/10.5658/wood.2022.50.1.12","url":null,"abstract":"Many studies on plant extracts have been reported for the treatment of candidiasis caused by Candida albicans, a representative fungal infection. This study demonstrates the synergistic antifungal activity of the combination of Phellodendri Cortex and Magnoliae Cortex, previously reported to have antifungal efficacy. Considering the antifungal efficacy and the separation of the active constituents, berberine and magnolol, hot water extraction and carbon dioxide supercritical extraction were selected for Phellodendri Cortex and Magnoliae Cortex, respectively. A combination of 0.55 g/L hot water extract of Phellodendri Cortex and 0.59 g/L carbon dioxide supercritical extract of Magnoliae Cortex showed synergistic antifungal activity. The synergistic antifungal activity of 160 μM berberine and 100 μM magnolol, which are representative antifungal compounds of Phellodendri Cortex and Magnoliae Cortex, respectively, contributes to the synergistic antifungal effect of their extracts. The additive decrease in cellular ergosterol level and the increased antifungal efficacy by extracellular ergosterol suggest that disruption of the biological function of ergosterol in the cell membrane is not responsible for the synergistic antifungal activity of berberine and magnolol. Synergistic cellular release of chromosomal DNA upon mixing berberine and magnolol indicates that disruption of the cellular structure is responsible for the synergistic antifungal effect of berberine and magnolol.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2022-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44752577","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-01-01DOI: 10.5658/wood.2022.50.1.46
Y. Hadi, E. N. Herliyana, G. Pari, R. Pari, I. B. Abdillah
Wood from tropical plantation forests has lower physical and mechanical properties than mature wood. Furfuryl alcohol (FA) impregnation into the wood could help to enhance hydrophobic properties, dimensional stability, and structural strength. Furfurylation was applied to specimens of the following four fast-growing tropical wood species: jabon (Anthocephalus cadamba), sengon (Falcataria moluccana), mangium (Acacia mangium), and pine (Pinus merkusii). The discoloration and physical and mechanical properties were subsequently measured, and the results showed that furfurylated wood had a darker color and better physical and mechanical properties than untreated wood. Specifically, the furfurylated wood had higher density, modulus of elasticity, and hardness and lower moisture content, water absorption, swelling, and shrinkage. The furfurylation significantly enhanced physical and mechanical properties.
{"title":"Furfurylation Effects on Discoloration and Physical-Mechanical Properties of Wood from Tropical Plantation Forests","authors":"Y. Hadi, E. N. Herliyana, G. Pari, R. Pari, I. B. Abdillah","doi":"10.5658/wood.2022.50.1.46","DOIUrl":"https://doi.org/10.5658/wood.2022.50.1.46","url":null,"abstract":"Wood from tropical plantation forests has lower physical and mechanical properties than mature wood. Furfuryl alcohol (FA) impregnation into the wood could help to enhance hydrophobic properties, dimensional stability, and structural strength. Furfurylation was applied to specimens of the following four fast-growing tropical wood species: jabon (Anthocephalus cadamba), sengon (Falcataria moluccana), mangium (Acacia mangium), and pine (Pinus merkusii). The discoloration and physical and mechanical properties were subsequently measured, and the results showed that furfurylated wood had a darker color and better physical and mechanical properties than untreated wood. Specifically, the furfurylated wood had higher density, modulus of elasticity, and hardness and lower moisture content, water absorption, swelling, and shrinkage. The furfurylation significantly enhanced physical and mechanical properties.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2022-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44119071","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-01-01DOI: 10.5658/wood.2022.50.1.59
J. Jung, S. Ha, Jae-Kyung Yang
Dietary fiber is considered a feed ingredient with high nutritional value in the broiler feed industry. Pine chips contain a large amount of dietary fiber and require some modification for use as broiler feed. In this study, pine chips were subjected to steam explosion under different severity factor (Ro) conditions to improve the chemical and physical properties of dietary fiber. The highest water-holding capacity, oil-holding capacity, and swelling capacity were found for Ro 4.0, followed by Ro 4.5 and 3.5. The optimal condition for the steam explosion was determined to be Ro 4.0 (reaction temperature of 210°C, and reaction time of 6.0 min). Under these conditions, the water-holding capacity, oil-holding capacity, and swelling capacity of steam-exploded pine chips were 8.3 g/g, 6.5 g/g, and 5.0 mL/g, respectively. This study may contribute to the application of lignocellulose and related products in the broiler feed industry.
{"title":"Effect of Steam Explosion Condition on the Improvement of Physicochemical Properties of Pine Chips for Feed Additives","authors":"J. Jung, S. Ha, Jae-Kyung Yang","doi":"10.5658/wood.2022.50.1.59","DOIUrl":"https://doi.org/10.5658/wood.2022.50.1.59","url":null,"abstract":"Dietary fiber is considered a feed ingredient with high nutritional value in the broiler feed industry. Pine chips contain a large amount of dietary fiber and require some modification for use as broiler feed. In this study, pine chips were subjected to steam explosion under different severity factor (Ro) conditions to improve the chemical and physical properties of dietary fiber. The highest water-holding capacity, oil-holding capacity, and swelling capacity were found for Ro 4.0, followed by Ro 4.5 and 3.5. The optimal condition for the steam explosion was determined to be Ro 4.0 (reaction temperature of 210°C, and reaction time of 6.0 min). Under these conditions, the water-holding capacity, oil-holding capacity, and swelling capacity of steam-exploded pine chips were 8.3 g/g, 6.5 g/g, and 5.0 mL/g, respectively. This study may contribute to the application of lignocellulose and related products in the broiler feed industry.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2022-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44213690","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-01-01DOI: 10.5658/wood.2022.50.1.31
JeongKwan Roh, Hyun-Jin Jo
After manufacturing the natural dyed actual size Hanji using 11 kinds of plant natural dyeing materials and 2 kinds of animal natural dyeing materials, the color characteristics and color change and color fastness after post-mordanting were compared and discussed. The hues of 13 types of natural dyed Hanji were black, PB, and RP, each with 1 type, YP with 3 types, and Y with 7 types. Among the natural dyeing materials, Chinese ink, indigo and Lac showed high color yield and color difference, and violet-root cromwell and gardenia seeds showed low color yield. The color fastness of Hanji dyed with turpentine diluted Ottchil, Pagoda tree seeds, Chinese ink and indigo was excellent, while that of gardenia seeds and violet-root cromwell were very poor. After post-mordanting of natural dyed Hanji with Al, Cu, and Fe mordants, the hue changes were show up the Alnus firma, clove, lac and cochineal. In addition, the color difference was very diverse and was overall the most biggest due to Fe mordant. After 72 hr. of UV irradiation on post-mordanting natural dyed Hanji, hue change was observed in 3 types and color fastness was improved in 8 types by post-mordanting. The Hue and color fastness are significantly different depending on the type of natural dying materials and post-mordants. Therefore, when dyeing Hanji with natural dyes, it is necessary to dye with sufficient knowledges and informations about the desired color and fastness.
{"title":"Dyeing and Color Fastness Properties of Natural Dyed Actual Size Hanji","authors":"JeongKwan Roh, Hyun-Jin Jo","doi":"10.5658/wood.2022.50.1.31","DOIUrl":"https://doi.org/10.5658/wood.2022.50.1.31","url":null,"abstract":"After manufacturing the natural dyed actual size Hanji using 11 kinds of plant natural dyeing materials and 2 kinds of animal natural dyeing materials, the color characteristics and color change and color fastness after post-mordanting were compared and discussed. The hues of 13 types of natural dyed Hanji were black, PB, and RP, each with 1 type, YP with 3 types, and Y with 7 types. Among the natural dyeing materials, Chinese ink, indigo and Lac showed high color yield and color difference, and violet-root cromwell and gardenia seeds showed low color yield. The color fastness of Hanji dyed with turpentine diluted Ottchil, Pagoda tree seeds, Chinese ink and indigo was excellent, while that of gardenia seeds and violet-root cromwell were very poor. After post-mordanting of natural dyed Hanji with Al, Cu, and Fe mordants, the hue changes were show up the Alnus firma, clove, lac and cochineal. In addition, the color difference was very diverse and was overall the most biggest due to Fe mordant. After 72 hr. of UV irradiation on post-mordanting natural dyed Hanji, hue change was observed in 3 types and color fastness was improved in 8 types by post-mordanting. The Hue and color fastness are significantly different depending on the type of natural dying materials and post-mordants. Therefore, when dyeing Hanji with natural dyes, it is necessary to dye with sufficient knowledges and informations about the desired color and fastness.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2022-01-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43678210","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2021-11-01DOI: 10.5658/wood.2021.49.6.574
Hyun Mi Lee, Woo-Seok Jeon, Jei-Wan Lee
1) International efforts to prevent illegally logged wood are expanding around the world. The “Legal Wood Trade Promotion System” was enacted in Korea in 2019 to strengthen the legal import and distribution of commercial wood in Korea. Since then, this system has promoted and ensured that the imported wood and wood products are legal with respect to the country of origin, wood species, and harvested area. As verification methods, DNA analysis technology and anatomical analysis using a microscope are mainly used in conjunction. Therefore, in this study, wood species of plywood were identified by analyzing the anatomical characteristics of various wood products for the first time. Douglas fir (Pseudotsuga menziesii (Mirb.) Franco.) and larch (Larix kaempferi (Lamb.) Carriere) plywoods (7, 9 ply) were obtained from four companies that supply plywood in Korea. After cutting each company's plywood to a size of about 1 cm 3 , the layers from top to bottom were separated into single layers, and three sections were observed using an optical microscope. The results revealed that the plywood was composed of a mixture of softwood and hardwood wood species, pine wood species, poplar wood species, or a mixture of larch and pine wood species. Identification of wood species using microscopy is important and can enable the scientific analysis and verification of various wood products, including plywood, imported from countries where the likelihood of indiscriminate distribution of illegal wood and illegal logging is high.
{"title":"Analysis of Anatomical Characteristics for Wood Species Identification of Commercial Plywood in Korea","authors":"Hyun Mi Lee, Woo-Seok Jeon, Jei-Wan Lee","doi":"10.5658/wood.2021.49.6.574","DOIUrl":"https://doi.org/10.5658/wood.2021.49.6.574","url":null,"abstract":"1) International efforts to prevent illegally logged wood are expanding around the world. The “Legal Wood Trade Promotion System” was enacted in Korea in 2019 to strengthen the legal import and distribution of commercial wood in Korea. Since then, this system has promoted and ensured that the imported wood and wood products are legal with respect to the country of origin, wood species, and harvested area. As verification methods, DNA analysis technology and anatomical analysis using a microscope are mainly used in conjunction. Therefore, in this study, wood species of plywood were identified by analyzing the anatomical characteristics of various wood products for the first time. Douglas fir (Pseudotsuga menziesii (Mirb.) Franco.) and larch (Larix kaempferi (Lamb.) Carriere) plywoods (7, 9 ply) were obtained from four companies that supply plywood in Korea. After cutting each company's plywood to a size of about 1 cm 3 , the layers from top to bottom were separated into single layers, and three sections were observed using an optical microscope. The results revealed that the plywood was composed of a mixture of softwood and hardwood wood species, pine wood species, poplar wood species, or a mixture of larch and pine wood species. Identification of wood species using microscopy is important and can enable the scientific analysis and verification of various wood products, including plywood, imported from countries where the likelihood of indiscriminate distribution of illegal wood and illegal logging is high.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2021-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42646339","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2021-11-01DOI: 10.5658/wood.2021.49.6.658
Junnan Xu, Yang Liu, Mingyu Wen, H. Park, Jiajie Zhu, Yu-nan Liu
1) A novel flame retardant and antibacterial composite membrane coating for wood surfaces was prepared by adding POSS-based phosphorous nitrogen flame retardant (later referred to as NH2-POSS) and silver nanoparticles (Ag NPs) to chitosan (CS). The effects of NH2-POSS content (mass fractions of CS 0%, 0.5%, 1%, 3%, 5%, and 7%) on the structure and properties of the composite membrane coating on wood were investigated. The composite film was prepared by the method of blending and ducting. Contact angle, tensile property and antibacterial effects of the composite film were measured, and infrared spectroscopy was used. The results show that the addition of NH2-POSS can not only improve the toughness of the membrane, but also the flame retardancy of the membrane, which improves the application of the membrane in wood products. However, with the addition of NH2-POSS, the transparency of the composite membrane was weakened. The inhibitory effect of the composite membrane on the growth of Escherichia coli was enhanced with the increase in Ag NPs. This research provides a foundation for the application of functional wood.
{"title":"Preparation of Flame Retardant and Antibacterial Wood with Composite Membrane Coating","authors":"Junnan Xu, Yang Liu, Mingyu Wen, H. Park, Jiajie Zhu, Yu-nan Liu","doi":"10.5658/wood.2021.49.6.658","DOIUrl":"https://doi.org/10.5658/wood.2021.49.6.658","url":null,"abstract":"1) A novel flame retardant and antibacterial composite membrane coating for wood surfaces was prepared by adding POSS-based phosphorous nitrogen flame retardant (later referred to as NH2-POSS) and silver nanoparticles (Ag NPs) to chitosan (CS). The effects of NH2-POSS content (mass fractions of CS 0%, 0.5%, 1%, 3%, 5%, and 7%) on the structure and properties of the composite membrane coating on wood were investigated. The composite film was prepared by the method of blending and ducting. Contact angle, tensile property and antibacterial effects of the composite film were measured, and infrared spectroscopy was used. The results show that the addition of NH2-POSS can not only improve the toughness of the membrane, but also the flame retardancy of the membrane, which improves the application of the membrane in wood products. However, with the addition of NH2-POSS, the transparency of the composite membrane was weakened. The inhibitory effect of the composite membrane on the growth of Escherichia coli was enhanced with the increase in Ag NPs. This research provides a foundation for the application of functional wood.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2021-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44851187","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2021-11-01DOI: 10.5658/wood.2021.49.6.541
Sei-Chang Oh
{"title":"Residual Strength Estimation of Decayed Wood by Insect Damage through in Situ Screw Withdrawal Strength and Compression Parallel to the Grain Related to Density","authors":"Sei-Chang Oh","doi":"10.5658/wood.2021.49.6.541","DOIUrl":"https://doi.org/10.5658/wood.2021.49.6.541","url":null,"abstract":"","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2021-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"45266405","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2021-11-01DOI: 10.5658/wood.2021.49.6.566
Hyoung-Woo Lee, Eun-Ju Lee
1) We investigated color changes on the outer surfaces of Phyllostachys bambusoides bam-boo by heat treatment under three different temperatures (180°C, 200°C, and 220°C) for three different durations (60 min, 90 min, and 120 min). A method of predicting the bam-boo surface color change after heat treatment was developed to provide valuable information and increase the added value of domestic bamboo products. The three average color parameters L*, a*, and b* decreased, and the overall color changes increased as the severity factor increased. The values of L* × a* × b* were highly related to the severity factor, and the optimal duration time for the desired bamboo surface color with a certain heat-treatment temperature could be estimated.
{"title":"Effects of Hot-Air Heat Treatment on the Surface Color of Phyllostachys bambusoides Bamboo","authors":"Hyoung-Woo Lee, Eun-Ju Lee","doi":"10.5658/wood.2021.49.6.566","DOIUrl":"https://doi.org/10.5658/wood.2021.49.6.566","url":null,"abstract":"1) We investigated color changes on the outer surfaces of Phyllostachys bambusoides bam-boo by heat treatment under three different temperatures (180°C, 200°C, and 220°C) for three different durations (60 min, 90 min, and 120 min). A method of predicting the bam-boo surface color change after heat treatment was developed to provide valuable information and increase the added value of domestic bamboo products. The three average color parameters L*, a*, and b* decreased, and the overall color changes increased as the severity factor increased. The values of L* × a* × b* were highly related to the severity factor, and the optimal duration time for the desired bamboo surface color with a certain heat-treatment temperature could be estimated.","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2021-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47522534","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2021-11-01DOI: 10.5658/wood.2021.49.6.550
Kwang-Hee Lee, C. Park, S. Kim
{"title":"Species Identification and Tree-Ring Dating of the Wooden Elements Used in Juheulgwan of Joryeong (Gate No.1), Mungyeong, Korea","authors":"Kwang-Hee Lee, C. Park, S. Kim","doi":"10.5658/wood.2021.49.6.550","DOIUrl":"https://doi.org/10.5658/wood.2021.49.6.550","url":null,"abstract":"","PeriodicalId":17357,"journal":{"name":"Journal of the Korean wood science and technology","volume":null,"pages":null},"PeriodicalIF":0.0,"publicationDate":"2021-11-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46619673","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：