In this study, the blended cements produced by using the building stone waste were exposed to sulphate solution and the cement properties were examined. Prepared mortar specimens were cured under water for 28 days and then they were exposed to three different proportions of sodium sulphate solution for 125 days. Performances of cements were determined by means of compressive strength and tensile strength tests. The broken parts of some mortar bars were examined with scanning electron microscope (SEM). Besides, they were left under moist atmosphere and their length change was measured and continuously monitored for period of 125 days. In blended cements, solely cements obtained by replacing 10–20% of diatomites gave similar strength values with ordinary Portland cement (CEM I 42.5R) at the ages of 7, 28, and 56 days. In all mortar specimens that included either waste andesite (AP) or marble powder (MP) showed best performance against very severe effective sodium sulphate solutions (13500 mg/L).
在本研究中，利用建筑石料废料制备水泥，并将其暴露于硫酸盐溶液中，对水泥性能进行了研究。制备好的砂浆试件在水下固化28天，然后在三种不同比例的硫酸钠溶液中暴露125天。水泥的性能通过抗压强度和抗拉强度试验来确定。用扫描电镜对砂浆杆的断裂部位进行了观察。将其放置在潮湿的空气中，测量其长度变化，连续监测125 d。在混合水泥中，单独替换10-20%硅藻土获得的水泥在7、28和56天龄时的强度值与普通波特兰水泥(CEM I 42.5R)相似。在所有砂浆样品中，包括废安山岩(AP)或大理石粉(MP)，在非常严重的有效硫酸钠溶液(13500 mg/L)中表现出最佳性能。
{"title":"Sodium Sulphate Effect on Cement Produced with Building Stone Waste","authors":"E. Sancak, Ş. Özkan","doi":"10.1155/2015/813515","DOIUrl":"https://doi.org/10.1155/2015/813515","url":null,"abstract":"In this study, the blended cements produced by using the building stone waste were exposed to sulphate solution and the cement properties were examined. Prepared mortar specimens were cured under water for 28 days and then they were exposed to three different proportions of sodium sulphate solution for 125 days. Performances of cements were determined by means of compressive strength and tensile strength tests. The broken parts of some mortar bars were examined with scanning electron microscope (SEM). Besides, they were left under moist atmosphere and their length change was measured and continuously monitored for period of 125 days. In blended cements, solely cements obtained by replacing 10–20% of diatomites gave similar strength values with ordinary Portland cement (CEM I 42.5R) at the ages of 7, 28, and 56 days. In all mortar specimens that included either waste andesite (AP) or marble powder (MP) showed best performance against very severe effective sodium sulphate solutions (13500 mg/L).","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"28 1","pages":"1-12"},"PeriodicalIF":0.0,"publicationDate":"2015-05-07","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75027379","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
This research investigates the fresh behaviour and mechanical properties of self-compacting concrete (SCC) containing high volume of limestone, metakaolin, silica fume, zeolite, and viscosity modifying admixture. Two fine aggregates with different fineness modulus were also utilized to evaluate the effect of sand’s gradation on the mechanical and flow properties of SCC containing inert and pozzolanic powder. Slump flow, V-funnel for fresh concrete and 5-minute-old concrete, J-ring, Orimet with and without J-ring, and L-box and U-box tests were performed on all 14 fresh concrete mixtures to examine the fresh properties of self-compacting concrete. Compressive strength of hardened specimens was measured at 7 and 35 days and tensile strength was also determined at the age of 28 days. The results show that sand grading significantly affects the fresh properties of SCC. It is also concluded that high volume of active powders including metakaolin, zeolite, and silica fume could not improve both the flow and mechanical properties of SCC at the same time. Limestone can be effectively used as filler in SCC in high volume content. A new set of limits for the L-box and U-box tests for SCC containing silica fume is also recommended as the existing criteria are not satisfactory.
{"title":"Effect of Inert and Pozzolanic Materials on Flow and Mechanical Properties of Self-Compacting Concrete","authors":"Mehrdad Mahoutian, M. Shekarchi","doi":"10.1155/2015/239717","DOIUrl":"https://doi.org/10.1155/2015/239717","url":null,"abstract":"This research investigates the fresh behaviour and mechanical properties of self-compacting concrete (SCC) containing high volume of limestone, metakaolin, silica fume, zeolite, and viscosity modifying admixture. Two fine aggregates with different fineness modulus were also utilized to evaluate the effect of sand’s gradation on the mechanical and flow properties of SCC containing inert and pozzolanic powder. Slump flow, V-funnel for fresh concrete and 5-minute-old concrete, J-ring, Orimet with and without J-ring, and L-box and U-box tests were performed on all 14 fresh concrete mixtures to examine the fresh properties of self-compacting concrete. Compressive strength of hardened specimens was measured at 7 and 35 days and tensile strength was also determined at the age of 28 days. The results show that sand grading significantly affects the fresh properties of SCC. It is also concluded that high volume of active powders including metakaolin, zeolite, and silica fume could not improve both the flow and mechanical properties of SCC at the same time. Limestone can be effectively used as filler in SCC in high volume content. A new set of limits for the L-box and U-box tests for SCC containing silica fume is also recommended as the existing criteria are not satisfactory.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"71 1","pages":"1-11"},"PeriodicalIF":0.0,"publicationDate":"2015-03-31","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75741208","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The nondestructive methods applied to the evaluation of concrete use different parameters to be related in the estimated resistance of concrete or other properties. The conducted study has evaluated a qualitative method of thermochemical degradation in concrete and mortar using a solvent acid whose chemical energy is capable of degrading the material. The reported study consisted in performing laboratory tests on mechanical compressive strength of concrete and mortar and thermochemical tests performed on little cores of concrete or mortar immersed in hydrochloric acid contained in a calorimeter system, obtaining several parameters as the time of thermal equilibrium, increase of temperature, degradation energy, and mass loss due to the thermochemical reaction. From the obtained results, these variables were analyzed and served as a parameter to be related with the concrete or mortar strength. The best parameter proved to be a good estimator was the increase of temperature and its degradation energy, whose value was inversely proportional to the strength of the material. Also, it is found that the most significant mechanisms that influenced the thermochemical reaction are the calcium content and the water chemically bound in the cement paste to perform the thermochemical test.
{"title":"A Qualitative Study of Thermochemical Degradation Related with Concrete and Mortar Strength","authors":"José Mora-Ruacho, H. A. Monreal-Romero","doi":"10.1155/2015/502405","DOIUrl":"https://doi.org/10.1155/2015/502405","url":null,"abstract":"The nondestructive methods applied to the evaluation of concrete use different parameters to be related in the estimated resistance of concrete or other properties. The conducted study has evaluated a qualitative method of thermochemical degradation in concrete and mortar using a solvent acid whose chemical energy is capable of degrading the material. The reported study consisted in performing laboratory tests on mechanical compressive strength of concrete and mortar and thermochemical tests performed on little cores of concrete or mortar immersed in hydrochloric acid contained in a calorimeter system, obtaining several parameters as the time of thermal equilibrium, increase of temperature, degradation energy, and mass loss due to the thermochemical reaction. From the obtained results, these variables were analyzed and served as a parameter to be related with the concrete or mortar strength. The best parameter proved to be a good estimator was the increase of temperature and its degradation energy, whose value was inversely proportional to the strength of the material. Also, it is found that the most significant mechanisms that influenced the thermochemical reaction are the calcium content and the water chemically bound in the cement paste to perform the thermochemical test.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"22 1","pages":"1-7"},"PeriodicalIF":0.0,"publicationDate":"2015-03-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"76151022","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
In his 1952 publication, Ergun made the following proclamation: “Data of the present investigation and those presented earlier have been treated accordingly, and the coefficients and have been determined by the method of least squares. The values obtained are and, , representing 640 experiments.” In this paper, we demonstrate that because his experimental methodology was flawed, the corrected values, which his experimental results would otherwise have established for these coefficients, are significantly higher. This is, in part, because Ergun’s reporting of his measured data was ambiguous with respect to the embedded coefficients and . In addition, this ambiguity made it difficult for any subsequent researcher to figure out the true meaning of his empirical results which, in turn, resulted in his choice of the values for these coefficients being accepted by default in the scientific community.
{"title":"A Reconciliation of Packed Column Permeability Data: Deconvoluting the Ergun Papers","authors":"H. Quinn","doi":"10.1155/2014/548482","DOIUrl":"https://doi.org/10.1155/2014/548482","url":null,"abstract":"In his 1952 publication, Ergun made the following proclamation: “Data of the present investigation and those presented earlier have been treated accordingly, and the coefficients and have been determined by the method of least squares. The values obtained are and, , representing 640 experiments.” In this paper, we demonstrate that because his experimental methodology was flawed, the corrected values, which his experimental results would otherwise have established for these coefficients, are significantly higher. This is, in part, because Ergun’s reporting of his measured data was ambiguous with respect to the embedded coefficients and . In addition, this ambiguity made it difficult for any subsequent researcher to figure out the true meaning of his empirical results which, in turn, resulted in his choice of the values for these coefficients being accepted by default in the scientific community.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"6 1","pages":"1-24"},"PeriodicalIF":0.0,"publicationDate":"2014-09-22","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"78970339","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Idris Abdulrahman, H. Tijani, Bashir Mohammed, H. Saidu, Hindatu Yusuf, Mohammed Ndejiko Jibrin, Sulaiman Mohammed
The conversion of waste obtained from agricultural processes into biocompatible materials (biomaterials) used in medical surgery is a strategy that will add more value in waste utilization. This strategy has successfully turned the rather untransformed wastes into high value products. Eggshell is an agricultural waste largely considered as useless and is discarded mostly because it contributes to pollution. This waste has potential for producing hydroxyapatite, a major component found in bone and teeth. Hydroxyapatite is an excellent material used in bone repair and tissue regeneration. The use of eggshell to generate hydroxyapatite will reduce the pollution effect of the waste and the subsequent conversion of the waste into a highly valuable product. In this paper, we reviewed the utilization of this agricultural waste (eggshell) in producing hydroxyapatite. The process of transforming eggshell into hydroxyapatite and nanohydroxyapatite is an environmentally friendly process. Eggshell based hydroxyapatite and nanohydroxyapatite stand as good chance of reducing the cost of treatment in bone repair or replacement with little impact on the environment.
{"title":"From Garbage to Biomaterials: An Overview on Egg Shell Based Hydroxyapatite","authors":"Idris Abdulrahman, H. Tijani, Bashir Mohammed, H. Saidu, Hindatu Yusuf, Mohammed Ndejiko Jibrin, Sulaiman Mohammed","doi":"10.1155/2014/802467","DOIUrl":"https://doi.org/10.1155/2014/802467","url":null,"abstract":"The conversion of waste obtained from agricultural processes into biocompatible materials (biomaterials) used in medical surgery is a strategy that will add more value in waste utilization. This strategy has successfully turned the rather untransformed wastes into high value products. Eggshell is an agricultural waste largely considered as useless and is discarded mostly because it contributes to pollution. This waste has potential for producing hydroxyapatite, a major component found in bone and teeth. Hydroxyapatite is an excellent material used in bone repair and tissue regeneration. The use of eggshell to generate hydroxyapatite will reduce the pollution effect of the waste and the subsequent conversion of the waste into a highly valuable product. In this paper, we reviewed the utilization of this agricultural waste (eggshell) in producing hydroxyapatite. The process of transforming eggshell into hydroxyapatite and nanohydroxyapatite is an environmentally friendly process. Eggshell based hydroxyapatite and nanohydroxyapatite stand as good chance of reducing the cost of treatment in bone repair or replacement with little impact on the environment.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"107 1","pages":"1-6"},"PeriodicalIF":0.0,"publicationDate":"2014-08-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"89696738","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Fiber plays an important role in determining the hardness, strength, and dynamic mechanical properties of composite material. In the present work, enhancement of viscoelastic behaviour of hybrid phenolic composites has been synergistically investigated. Five different phenolic composites, namely, C1, C2, C3, C4, and C5, were fabricated by varying the weight percentage of basalt and aramid fiber, namely, 25, 20, 15, 10, and 5% by compensating with barium sulphate (BaSO4) to keep the combined reinforcement concentration at 25 wt%. Hardness was measured to examine the resistance of composites to indentation. The hardness of phenolic composites increased from 72.2 to 85.2 with increase in basalt fiber loading. Composite C1 (25 wt% fiber) is 1.2 times harder than composite C5. Compression test was conducted to find out compressive strength of phenolic composites and compressive strength increased with increase in fiber content. Dynamic mechanical analysis (DMA) was carried out to assess the temperature dependence mechanical properties in terms of storage modulus ( ), loss modulus ( ), and damping factor (tan δ). The results indicate great improvement of values and decrease in damping behaviour of composite upon fiber addition. Further X-ray powder diffraction (XRD) and energy-dispersive X-ray (EDX) analysis were employed to characterize the friction composites.
{"title":"Effect of Short Fiber Reinforcement on Mechanical Properties of Hybrid Phenolic Composites","authors":"S. Manoharan, B. Suresha, G. Ramadoss, B. Bharath","doi":"10.1155/2014/478549","DOIUrl":"https://doi.org/10.1155/2014/478549","url":null,"abstract":"Fiber plays an important role in determining the hardness, strength, and dynamic mechanical properties of composite material. In the present work, enhancement of viscoelastic behaviour of hybrid phenolic composites has been synergistically investigated. Five different phenolic composites, namely, C1, C2, C3, C4, and C5, were fabricated by varying the weight percentage of basalt and aramid fiber, namely, 25, 20, 15, 10, and 5% by compensating with barium sulphate (BaSO4) to keep the combined reinforcement concentration at 25 wt%. Hardness was measured to examine the resistance of composites to indentation. The hardness of phenolic composites increased from 72.2 to 85.2 with increase in basalt fiber loading. Composite C1 (25 wt% fiber) is 1.2 times harder than composite C5. Compression test was conducted to find out compressive strength of phenolic composites and compressive strength increased with increase in fiber content. Dynamic mechanical analysis (DMA) was carried out to assess the temperature dependence mechanical properties in terms of storage modulus ( ), loss modulus ( ), and damping factor (tan δ). The results indicate great improvement of values and decrease in damping behaviour of composite upon fiber addition. Further X-ray powder diffraction (XRD) and energy-dispersive X-ray (EDX) analysis were employed to characterize the friction composites.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"10 1","pages":"1-9"},"PeriodicalIF":0.0,"publicationDate":"2014-08-06","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"90116567","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Application of nanoscale science to construction material has already begun. In recent times, various nanofibers have raised the interest of researchers due to their exceptional mechanical properties and high potential to be used as reinforcement within cement matrix. Carbon nanotube (CNT) is one of the most important areas of research in the field of nanotechnology. The size and exceptional mechanical properties of CNT show their high potential to be used to produce high performance next generation cementitious composites. In this study, an attempt has been made to investigate the effect of size of CNTs on compressive strengths of CNT reinforced cement composites. Seven different sizes of multiwalled nanotubes (MWNTs) were used to produce MWNT-cement composites. A trend was observed regarding the effect of nanotube size on compressive strength of composites in most cases. MWNT with outside diameter (OD) of 20 nm or less exhibited relatively better performance. Smaller MWNT can be distributed at much finer scale and consequently filling the nanopore space within the cement matrix more efficiently. This in turn resulted in stronger composites.
{"title":"Effect of Carbon Nanotube Size on Compressive Strengths of Nanotube Reinforced Cementitious Composites","authors":"T. Manzur, N. Yazdani, Md Abul Bashar Emon","doi":"10.1155/2014/960984","DOIUrl":"https://doi.org/10.1155/2014/960984","url":null,"abstract":"Application of nanoscale science to construction material has already begun. In recent times, various nanofibers have raised the interest of researchers due to their exceptional mechanical properties and high potential to be used as reinforcement within cement matrix. Carbon nanotube (CNT) is one of the most important areas of research in the field of nanotechnology. The size and exceptional mechanical properties of CNT show their high potential to be used to produce high performance next generation cementitious composites. In this study, an attempt has been made to investigate the effect of size of CNTs on compressive strengths of CNT reinforced cement composites. Seven different sizes of multiwalled nanotubes (MWNTs) were used to produce MWNT-cement composites. A trend was observed regarding the effect of nanotube size on compressive strength of composites in most cases. MWNT with outside diameter (OD) of 20 nm or less exhibited relatively better performance. Smaller MWNT can be distributed at much finer scale and consequently filling the nanopore space within the cement matrix more efficiently. This in turn resulted in stronger composites.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"77 1","pages":"1-8"},"PeriodicalIF":0.0,"publicationDate":"2014-07-17","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"79845277","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Tian-xu Wang, D. Kevorkov, Ahmad Mostafa, M. Medraj
Al-Mn-Zn ternary system is experimentally investigated at 400°C using diffusion couples and key alloys. Phase relationships and homogeneity ranges are determined for binary and ternary compounds using EPMA, SEM/EDS, and XRD. Reported ternary compound T3 (Al11Mn3Zn2) is confirmed in this study and is denoted as τ2 in this paper. Two new ternary compounds (τ1 and τ3) are observed in this system at 400°C. τ1 is determined as a stoichiometric compound with the composition of Al31Mn8Zn11. τ3 has been found to have homogeneity range of AlxMnyZnz ( at%; at%; at%). The binary compounds Al4Mn and Al11Mn4 exhibit limited solid solubility of around 6 at% and 4 at% Zn, respectively. Terminal solid solution Al8Mn5 is found to have maximum ternary solubility of about 10 at% Zn. In addition, ternary solubility of Al-rich β-Mn′ at 400°C is determined as 4 at% Zn. Zn-rich β-Mn′′ has a ternary solubility of 3 at% Al. The solubility of Al in Mn5Zn21 is measured as 5 at%. Based on the current experimental results, the isothermal section of Al-Mn-Zn ternary system at 400°C has been constructed.
{"title":"Experimental Investigation of the Phase Equilibria in the Al-Mn-Zn System at 400°C","authors":"Tian-xu Wang, D. Kevorkov, Ahmad Mostafa, M. Medraj","doi":"10.1155/2014/451587","DOIUrl":"https://doi.org/10.1155/2014/451587","url":null,"abstract":"Al-Mn-Zn ternary system is experimentally investigated at 400°C using diffusion couples and key alloys. Phase relationships and homogeneity ranges are determined for binary and ternary compounds using EPMA, SEM/EDS, and XRD. Reported ternary compound T3 (Al11Mn3Zn2) is confirmed in this study and is denoted as τ2 in this paper. Two new ternary compounds (τ1 and τ3) are observed in this system at 400°C. τ1 is determined as a stoichiometric compound with the composition of Al31Mn8Zn11. τ3 has been found to have homogeneity range of AlxMnyZnz ( at%; at%; at%). The binary compounds Al4Mn and Al11Mn4 exhibit limited solid solubility of around 6 at% and 4 at% Zn, respectively. Terminal solid solution Al8Mn5 is found to have maximum ternary solubility of about 10 at% Zn. In addition, ternary solubility of Al-rich β-Mn′ at 400°C is determined as 4 at% Zn. Zn-rich β-Mn′′ has a ternary solubility of 3 at% Al. The solubility of Al in Mn5Zn21 is measured as 5 at%. Based on the current experimental results, the isothermal section of Al-Mn-Zn ternary system at 400°C has been constructed.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"115 1","pages":"1-13"},"PeriodicalIF":0.0,"publicationDate":"2014-07-17","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"89373297","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Cu xAg 1−xInS 2 solid thin films were fabricated through a low-cost process. Particular process-related enhanced properties lead to reaching a minimum of lattice mismatch between absorber and buffer layers within particular solar cell devices. First, copper-less samples X-ray diffraction analysis depicts the presence of AgInS 2 ternary compound in chalcopyrite tetragonal phase with privileged (112) peak ( A) according to JCPDS 75-0118 card. Second, when x content increases, we note a shift of the same preferential orientation (112) and its value reaches 1.63 A corresponding to CuInS 2 chalcopyrite tetragonal material according to JCPDS 89-6095 file. Finally, the formation and stability of these quaternaries have been discussed in terms of the lattice compatibility in relation with silver-copper duality within indium disulfide lattice structure. Plausible explanations for the extent and dynamics of copper incorporation inside AgInS 2 elaborated ternary matrices have been proposed.
{"title":"Structural Investigation of Photocatalyst Solid Ag1−xCuxInS2 Quaternary Alloys Sprayed Thin Films Optimized within the Lattice Compatibility Theory (LCT) Scope","authors":"A. Colantoni, L. Longo, K. Boubaker","doi":"10.1155/2014/325271","DOIUrl":"https://doi.org/10.1155/2014/325271","url":null,"abstract":"Cu xAg 1−xInS 2 solid thin films were fabricated through a low-cost process. Particular process-related enhanced properties lead to reaching a minimum of lattice mismatch between absorber and buffer layers within particular solar cell devices. First, copper-less samples X-ray diffraction analysis depicts the presence of AgInS 2 ternary compound in chalcopyrite tetragonal phase with privileged (112) peak ( A) according to JCPDS 75-0118 card. Second, when x content increases, we note a shift of the same preferential orientation (112) and its value reaches 1.63 A corresponding to CuInS 2 chalcopyrite tetragonal material according to JCPDS 89-6095 file. Finally, the formation and stability of these quaternaries have been discussed in terms of the lattice compatibility in relation with silver-copper duality within indium disulfide lattice structure. Plausible explanations for the extent and dynamics of copper incorporation inside AgInS 2 elaborated ternary matrices have been proposed.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"7 1","pages":"1-5"},"PeriodicalIF":0.0,"publicationDate":"2014-07-14","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"81674369","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Single crystals of BGHB were grown by slow evaporation technique. The unit cell dimensions and space group of the grown crystals were confirmed by single crystal X-ray diffraction. The modes of vibration of the molecules and the presence of functional groups were identified using FTIR technique. The microhardness study shows that the Vickers hardness number of the crystal increases with the increase in applied load. The optical properties of the crystals were determined using UV-Visible spectroscopy. The thermal properties of the grown crystal were also determined. The refractive index was determined as 1.396 using Brewster’s angle method. The emission of green light on passing the Nd: YAG laser light confirmed the second harmonic generation property of the crystals and the SHG efficiency of the crystals was found to be higher than that of KDP. The dielectric constant and dielectric loss measurements were carried out for different temperatures and frequencies. The ac conductivity study of the crystals was also discussed. The photoconductivity studies confirm that the grown crystal has negative photoconductivity nature. The etching studies were carried out to study the formation of etch pits.
{"title":"Synthesis, Growth, and Characterization of Bisglycine Hydrobromide Single Crystal","authors":"K. Pandurangan, S. Suresh","doi":"10.1155/2014/362678","DOIUrl":"https://doi.org/10.1155/2014/362678","url":null,"abstract":"Single crystals of BGHB were grown by slow evaporation technique. The unit cell dimensions and space group of the grown crystals were confirmed by single crystal X-ray diffraction. The modes of vibration of the molecules and the presence of functional groups were identified using FTIR technique. The microhardness study shows that the Vickers hardness number of the crystal increases with the increase in applied load. The optical properties of the crystals were determined using UV-Visible spectroscopy. The thermal properties of the grown crystal were also determined. The refractive index was determined as 1.396 using Brewster’s angle method. The emission of green light on passing the Nd: YAG laser light confirmed the second harmonic generation property of the crystals and the SHG efficiency of the crystals was found to be higher than that of KDP. The dielectric constant and dielectric loss measurements were carried out for different temperatures and frequencies. The ac conductivity study of the crystals was also discussed. The photoconductivity studies confirm that the grown crystal has negative photoconductivity nature. The etching studies were carried out to study the formation of etch pits.","PeriodicalId":17611,"journal":{"name":"Journal: Materials","volume":"18 1","pages":"1-7"},"PeriodicalIF":0.0,"publicationDate":"2014-06-29","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"83921787","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：