Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-03
Gia Thanh Nguyen, Mi Le Thi Diem, N. Huynh
The study was carried out to assess the pollution, impact, and risk level to the surface water environment of pollutants in the water bodies of Soc Trang province, Vietnam. The parameters for evaluating surface water quality and risks included temperature, pH, TSS, DO, BOD, COD, NH4+-N, NO2--N, NO3--N, PO43--P, Cl-, Fet, and coliform. Surface water samples were collected at 35 locations with a frequency of six times (February, April, June, August, October, and December) in 2022. The water quality index (WQI), impact and risk level (risk quotient or RQ, RQ-F), correlation analysis, and principal component analysis (PCA) were utilized in the study. The results show that the surface water has been seriously polluted due to organic matter, nutrients, microorganisms, iron, and salinity. The values of WQI in the dry and rainy seasons fluctuated between bad and very good, indicating that surface water quality is suitable for water transport and other purposes with higher quality requirements. TSS, COD, Fet and coliform have a high impact and risk for the environment in this study area. There were no environmental impacts and risks to NO3--N. Locations with many high-risk pollutants were mainly distributed in residential and coastal areas. The significant negative correlation between the WQI and RQ indicated that the lower the WQI, the higher the environmental risk. The PCA results show that at least six polluting sources affected water quality and caused environmental risks. The results of this study contribute essential and valuable information for improving water quality in the study area through the assessment of environmental impacts and risks. Doi: 10.28991/CEJ-2023-09-08-03 Full Text: PDF
{"title":"Pollution and Risk Level Assessment of Pollutants in Surface Water Bodies","authors":"Gia Thanh Nguyen, Mi Le Thi Diem, N. Huynh","doi":"10.28991/cej-2023-09-08-03","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-03","url":null,"abstract":"The study was carried out to assess the pollution, impact, and risk level to the surface water environment of pollutants in the water bodies of Soc Trang province, Vietnam. The parameters for evaluating surface water quality and risks included temperature, pH, TSS, DO, BOD, COD, NH4+-N, NO2--N, NO3--N, PO43--P, Cl-, Fet, and coliform. Surface water samples were collected at 35 locations with a frequency of six times (February, April, June, August, October, and December) in 2022. The water quality index (WQI), impact and risk level (risk quotient or RQ, RQ-F), correlation analysis, and principal component analysis (PCA) were utilized in the study. The results show that the surface water has been seriously polluted due to organic matter, nutrients, microorganisms, iron, and salinity. The values of WQI in the dry and rainy seasons fluctuated between bad and very good, indicating that surface water quality is suitable for water transport and other purposes with higher quality requirements. TSS, COD, Fet and coliform have a high impact and risk for the environment in this study area. There were no environmental impacts and risks to NO3--N. Locations with many high-risk pollutants were mainly distributed in residential and coastal areas. The significant negative correlation between the WQI and RQ indicated that the lower the WQI, the higher the environmental risk. The PCA results show that at least six polluting sources affected water quality and caused environmental risks. The results of this study contribute essential and valuable information for improving water quality in the study area through the assessment of environmental impacts and risks. Doi: 10.28991/CEJ-2023-09-08-03 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"2 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"90368033","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-011
T. Awolusi, O. Aladegboye, O. Babalola, E. K. Ayo, M. Azab, A. Deifalla
The growing concern to reduce global warming has necessitated the use of more eco-friendly materials in construction. The study is focused on the utilization of cassava peel ash as supplementary cementitious material and bamboo as reinforcement in concrete beams. The response surface methodology approach was explored to determine the effect of simultaneously varying the cassava peel ash content, bamboo size, beam length, and beam depth on the flexural strength and strain of beams. An analysis of variance was carried out on experimentally obtained results to determine the accuracy of the obtained models and the contributions made by the linear interaction and quadratic terms on flexural strength and flexural strain. The coefficient of determination obtained for RSM models showed a good correlation between all predicted and experimentally obtained results. The optimum conditions obtained for bamboo-reinforced concrete containing cassava peel ash were 3% cassava peel ash, 16 mm bamboo diameter, 500 mm beam length, and 150 mm beam depth. The predicted flexural strengths were 11.85, 14.34, and 14.95 N/mm2 and flexural strains of 0.64, 0.67, and 0.91 for 28 days, 56 days, and 90 days, respectively. To validate the model prediction, a laboratory experiment was conducted using the optimum mix design proportion. From the results obtained, it was observed that the experimental results were close to those predicted by the models. These models can be efficiently used for simulating the flexural behavior of bamboo-reinforced concrete beams. Doi: 10.28991/CEJ-2023-09-08-011 Full Text: PDF
{"title":"Optimizing the Flexural Behavior of Bamboo Reinforced Concrete Beams Containing Cassava Peel Ash using Response Surface Methodology","authors":"T. Awolusi, O. Aladegboye, O. Babalola, E. K. Ayo, M. Azab, A. Deifalla","doi":"10.28991/cej-2023-09-08-011","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-011","url":null,"abstract":"The growing concern to reduce global warming has necessitated the use of more eco-friendly materials in construction. The study is focused on the utilization of cassava peel ash as supplementary cementitious material and bamboo as reinforcement in concrete beams. The response surface methodology approach was explored to determine the effect of simultaneously varying the cassava peel ash content, bamboo size, beam length, and beam depth on the flexural strength and strain of beams. An analysis of variance was carried out on experimentally obtained results to determine the accuracy of the obtained models and the contributions made by the linear interaction and quadratic terms on flexural strength and flexural strain. The coefficient of determination obtained for RSM models showed a good correlation between all predicted and experimentally obtained results. The optimum conditions obtained for bamboo-reinforced concrete containing cassava peel ash were 3% cassava peel ash, 16 mm bamboo diameter, 500 mm beam length, and 150 mm beam depth. The predicted flexural strengths were 11.85, 14.34, and 14.95 N/mm2 and flexural strains of 0.64, 0.67, and 0.91 for 28 days, 56 days, and 90 days, respectively. To validate the model prediction, a laboratory experiment was conducted using the optimum mix design proportion. From the results obtained, it was observed that the experimental results were close to those predicted by the models. These models can be efficiently used for simulating the flexural behavior of bamboo-reinforced concrete beams. Doi: 10.28991/CEJ-2023-09-08-011 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"14 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"74146827","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-013
A. Elsheikh, H. H. Alzamili
One of the most significant building materials used to build a variety of infrastructure, military, and civil structures is concrete. It can effectively withstand fire mishaps for a long period of time. This study employs a finite element simulation approach in Three steps: the first involves applying mechanical loading, the second involves applying mechanical and thermal loading; and the third involves strengthening the damaged model. Two different strengthening procedures were used to evaluate the performance of the fire-damaged slab. Two types of strengthening techniques—carbon-fiber-reinforced polymer (CFRP) sheet and slurry-infiltrated fibrous concrete (SIFCON) jacketing—were used. Studying the performance of SIFCON and CFRP together and in two different thicknesses of each for repairing both normal and high-strength concretes after fire exposure is considered limited. An investigation of their behavior can provide insights into how effective the restoration of strength is. The study aims to assess how well various repair materials perform in restoring the durability and strength of reinforced concrete members after being exposed to fire. This will assist in determining the best materials for concrete repair after a fire. Results show that the enhancements by SIFCON with a thickness of 30 mm significantly improved many indices, including load displacement behavior, ductility, and absorption energy of the slab. Doi: 10.28991/CEJ-2023-09-08-013 Full Text: PDF
{"title":"Post Fire Behavior of Structural Reinforced Concrete Member (Slab) Repairing with Various Materials","authors":"A. Elsheikh, H. H. Alzamili","doi":"10.28991/cej-2023-09-08-013","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-013","url":null,"abstract":"One of the most significant building materials used to build a variety of infrastructure, military, and civil structures is concrete. It can effectively withstand fire mishaps for a long period of time. This study employs a finite element simulation approach in Three steps: the first involves applying mechanical loading, the second involves applying mechanical and thermal loading; and the third involves strengthening the damaged model. Two different strengthening procedures were used to evaluate the performance of the fire-damaged slab. Two types of strengthening techniques—carbon-fiber-reinforced polymer (CFRP) sheet and slurry-infiltrated fibrous concrete (SIFCON) jacketing—were used. Studying the performance of SIFCON and CFRP together and in two different thicknesses of each for repairing both normal and high-strength concretes after fire exposure is considered limited. An investigation of their behavior can provide insights into how effective the restoration of strength is. The study aims to assess how well various repair materials perform in restoring the durability and strength of reinforced concrete members after being exposed to fire. This will assist in determining the best materials for concrete repair after a fire. Results show that the enhancements by SIFCON with a thickness of 30 mm significantly improved many indices, including load displacement behavior, ductility, and absorption energy of the slab. Doi: 10.28991/CEJ-2023-09-08-013 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"58 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82127881","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-01
Woratid Wongpattanawut, Borvorn Israngkura Na Ayudhya
The objective of this study was to investigate the effect of curing temperature on the mechanical properties of sanitary ware porcelain powder-based geopolymer paste and mortar under various curing temperatures. The setting time, porosity, water absorption, and compressive strength of specimens mixed with alkaline concentrations of 8M, 10M, 12M, and 14M were compared. All mortar cube (50×50×50 mm) specimens were placed into drying ovens for 24 hours at 60°C, 75°C, 90°C, and 105°C, respectively. The specimens were then air-cured for 1, 3, 7, 14, and 28 days. The results showed that the elevated curing temperature accelerated the polymerization process of the porcelain geopolymerization reaction. The setting time varied between 89 mins and 380 mins. It showed variability depending on alkaline concentration and initial curing temperature. The setting time of pastes decreased when alkaline concentrations increased. An increasing temperature in the drying oven decreased the initial and final setting times. Similar to this, the rate of water absorption and permeability of porcelain-based geopolymer mortar specimens decreased with drying oven temperatures and increments in alkaline concentration. The lowest water absorption and porosity of the specimen were 2.1% and 15.7%, respectively. The compressive strength increased as drying oven temperatures and alkaline concentrations increased. The highest 28 day compressive strength was found in 14M specimens with 105°C curing temperatures. The ultimate compressive strength was 64.45 N/mm2. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were investigated to study the microstructural properties of the geopolymers. Doi: 10.28991/CEJ-2023-09-08-01 Full Text: PDF
{"title":"Effect of Curing Temperature on Mechanical Properties of Sanitary Ware Porcelain based Geopolymer Mortar","authors":"Woratid Wongpattanawut, Borvorn Israngkura Na Ayudhya","doi":"10.28991/cej-2023-09-08-01","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-01","url":null,"abstract":"The objective of this study was to investigate the effect of curing temperature on the mechanical properties of sanitary ware porcelain powder-based geopolymer paste and mortar under various curing temperatures. The setting time, porosity, water absorption, and compressive strength of specimens mixed with alkaline concentrations of 8M, 10M, 12M, and 14M were compared. All mortar cube (50×50×50 mm) specimens were placed into drying ovens for 24 hours at 60°C, 75°C, 90°C, and 105°C, respectively. The specimens were then air-cured for 1, 3, 7, 14, and 28 days. The results showed that the elevated curing temperature accelerated the polymerization process of the porcelain geopolymerization reaction. The setting time varied between 89 mins and 380 mins. It showed variability depending on alkaline concentration and initial curing temperature. The setting time of pastes decreased when alkaline concentrations increased. An increasing temperature in the drying oven decreased the initial and final setting times. Similar to this, the rate of water absorption and permeability of porcelain-based geopolymer mortar specimens decreased with drying oven temperatures and increments in alkaline concentration. The lowest water absorption and porosity of the specimen were 2.1% and 15.7%, respectively. The compressive strength increased as drying oven temperatures and alkaline concentrations increased. The highest 28 day compressive strength was found in 14M specimens with 105°C curing temperatures. The ultimate compressive strength was 64.45 N/mm2. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were investigated to study the microstructural properties of the geopolymers. Doi: 10.28991/CEJ-2023-09-08-01 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"101 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"85946849","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-04
Vishal Murugan, A. Bahrami, Rakshit Srivastava, K. Satyanarayanan, Prakash Murugan, J. Arvind
This article investigates the mechanical and postfire structural performances of concrete under elevated temperatures (200°C, 400°C, 600°C, and 800°C) after 7 and 28 days of concrete curing. The main objective of this study is to evaluate the post-fire behavior of concrete structures and how their modulus of elasticity values influence their structural parameters. Mechanical studies, namely, the compressive strength, splitting tensile strength, and flexural strength, were performed on cubes, cylinders, and prism beams under normal and elevated temperatures. Non-destructive tests, like rebound hammer and ultrasonic pulse velocity, were also conducted on concrete cubes to obtain the strength of concrete before and after heating the specimens. Microstructural studies, in particular, scanning electron microscope and energy dispersive x-ray spectroscopy, were done to analyze the changes in the chemical composition of concrete under the effect of the temperatures. The weight loss of the concrete specimens was assessed under the elevated temperatures. The results indicated that the geometric shapes of the specimens influenced the loss in the moisture content of concrete under an elevated temperature scenario. Microstructural studies revealed the changes in the chemical composition under the elevated temperatures. The results of this research can be further integrated for industrial applications. Doi: 10.28991/CEJ-2023-09-08-04 Full Text: PDF
{"title":"Mechanical and Postfire Structural Performances of Concrete under Elevated Temperatures","authors":"Vishal Murugan, A. Bahrami, Rakshit Srivastava, K. Satyanarayanan, Prakash Murugan, J. Arvind","doi":"10.28991/cej-2023-09-08-04","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-04","url":null,"abstract":"This article investigates the mechanical and postfire structural performances of concrete under elevated temperatures (200°C, 400°C, 600°C, and 800°C) after 7 and 28 days of concrete curing. The main objective of this study is to evaluate the post-fire behavior of concrete structures and how their modulus of elasticity values influence their structural parameters. Mechanical studies, namely, the compressive strength, splitting tensile strength, and flexural strength, were performed on cubes, cylinders, and prism beams under normal and elevated temperatures. Non-destructive tests, like rebound hammer and ultrasonic pulse velocity, were also conducted on concrete cubes to obtain the strength of concrete before and after heating the specimens. Microstructural studies, in particular, scanning electron microscope and energy dispersive x-ray spectroscopy, were done to analyze the changes in the chemical composition of concrete under the effect of the temperatures. The weight loss of the concrete specimens was assessed under the elevated temperatures. The results indicated that the geometric shapes of the specimens influenced the loss in the moisture content of concrete under an elevated temperature scenario. Microstructural studies revealed the changes in the chemical composition under the elevated temperatures. The results of this research can be further integrated for industrial applications. Doi: 10.28991/CEJ-2023-09-08-04 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"5 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"88863548","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-08
Z. Arifin, Nuha Khairunisa, B. Kristiawan, S. D. Prasetyo, Watuhumalang Bhre Bangun
Using solar energy through photovoltaic (PV) panels has excellent potential as an alternative energy source. However, the problem of high operating temperatures causing a reduction in work efficiency needs to be addressed. This study aimed to analyze the development of a cooling system to increase PV panels' electrical and thermal efficiency. The research involved analyzing the use of TiO2, Al2O3, and ZnO working fluids by adding 0.5 vol% to water in an active cooling method. The cooling system involved a rectangular spiral and a rectangular tube behind the PV panel. A solar simulator simulated solar radiation with intensity variations to analyze the cooling system's performance in different working conditions. The results showed that the heat exchanger with a nanofluid configuration reduced the panel temperature by 14 oC, which increased the electrical efficiency by up to 4.7% in the ZnO nanofluid. In the rectangular spiral configuration, the ZnO nanofluid reduced the panel temperature from 60 to 45 oC, increasing the Isc value from 2.16A to 2.9A and the Voc value from 21.5V to 23V. This resulted in a maximum power increase of the panel to 53W. Doi: 10.28991/CEJ-2023-09-08-08 Full Text: PDF
{"title":"Performance Analysis of Nanofluid-based Photovoltaic Thermal Collector with Different Convection Cooling Flow","authors":"Z. Arifin, Nuha Khairunisa, B. Kristiawan, S. D. Prasetyo, Watuhumalang Bhre Bangun","doi":"10.28991/cej-2023-09-08-08","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-08","url":null,"abstract":"Using solar energy through photovoltaic (PV) panels has excellent potential as an alternative energy source. However, the problem of high operating temperatures causing a reduction in work efficiency needs to be addressed. This study aimed to analyze the development of a cooling system to increase PV panels' electrical and thermal efficiency. The research involved analyzing the use of TiO2, Al2O3, and ZnO working fluids by adding 0.5 vol% to water in an active cooling method. The cooling system involved a rectangular spiral and a rectangular tube behind the PV panel. A solar simulator simulated solar radiation with intensity variations to analyze the cooling system's performance in different working conditions. The results showed that the heat exchanger with a nanofluid configuration reduced the panel temperature by 14 oC, which increased the electrical efficiency by up to 4.7% in the ZnO nanofluid. In the rectangular spiral configuration, the ZnO nanofluid reduced the panel temperature from 60 to 45 oC, increasing the Isc value from 2.16A to 2.9A and the Voc value from 21.5V to 23V. This resulted in a maximum power increase of the panel to 53W. Doi: 10.28991/CEJ-2023-09-08-08 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"57 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"91317085","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-012
Md. Shohel Sayeed, Huzaifah Abdulrahim, Siti Fatimah Abdul Razak, U. Bukar, S. Yogarayan
Due to the limited availability of parking slots in parking areas, drivers often have difficulty finding an empty parking slot. The number of parking slots available at a particular location is usually less than the number of vehicles. Hence, drivers spend a lot of time looking for vacant parking slots, which eventually delays the completion of their tasks, such as paying bills, attending a meeting, or visiting a patient at the hospital, etc. There are a couple of parking guidance systems that have been highlighted by the other researchers, but most of them lack real-time, convenient guidance. This research proposed a smart parking guidance system made of an IoT Raspberry Pi combined with an Android application that makes use of the weighted k nearest neighbours for positioning the vehicle. This was achieved through the use of Wi-Fi signal strength indicator fingerprinting, allowing for real-time navigation and parking detection. In order to achieve real-time parking over the internet, Raspberry Pi hardware and the ThingSpeak IoT cloud with ultrasonic sensors are used in the proposed method. An Android application was involved in this parking detection system, which adopted IoT approaches to estimate the location of users in real-time and provide routes using route-finding techniques to assist drivers in finding their desired parking slots. Data from the sensors was processed and translated into the Raspberry Pi using the Python programming language. They were sent using the Message Telemetry Transport protocol to send parking data to the ThingSpeak IoT cloud in real-time. This data was displayed via the Android app. The user is then able to view each available parking slot, acquire the route, and be directed with high accuracy to the parking slots of their choice. In this study, advanced sensing and communication technologies were used together with the weighted k nearest neighbours algorithm for positioning and wayfinding in order to improve parking guidance accuracy. Based on the experimental results, the proposed system showed a lower average error rate of 1.5 metres in comparison to other positioning techniques, such as GPS, or other similar algorithms for positioning, such as maximum a posteriori, which have shown average errors of 2.3 metres and 3.55 metres, respectively, a potential increase of more than 35% from the previous error rate. Doi: 10.28991/CEJ-2023-09-08-012 Full Text: PDF
{"title":"IoT Raspberry Pi Based Smart Parking System with Weighted K-Nearest Neighbours Approach","authors":"Md. Shohel Sayeed, Huzaifah Abdulrahim, Siti Fatimah Abdul Razak, U. Bukar, S. Yogarayan","doi":"10.28991/cej-2023-09-08-012","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-012","url":null,"abstract":"Due to the limited availability of parking slots in parking areas, drivers often have difficulty finding an empty parking slot. The number of parking slots available at a particular location is usually less than the number of vehicles. Hence, drivers spend a lot of time looking for vacant parking slots, which eventually delays the completion of their tasks, such as paying bills, attending a meeting, or visiting a patient at the hospital, etc. There are a couple of parking guidance systems that have been highlighted by the other researchers, but most of them lack real-time, convenient guidance. This research proposed a smart parking guidance system made of an IoT Raspberry Pi combined with an Android application that makes use of the weighted k nearest neighbours for positioning the vehicle. This was achieved through the use of Wi-Fi signal strength indicator fingerprinting, allowing for real-time navigation and parking detection. In order to achieve real-time parking over the internet, Raspberry Pi hardware and the ThingSpeak IoT cloud with ultrasonic sensors are used in the proposed method. An Android application was involved in this parking detection system, which adopted IoT approaches to estimate the location of users in real-time and provide routes using route-finding techniques to assist drivers in finding their desired parking slots. Data from the sensors was processed and translated into the Raspberry Pi using the Python programming language. They were sent using the Message Telemetry Transport protocol to send parking data to the ThingSpeak IoT cloud in real-time. This data was displayed via the Android app. The user is then able to view each available parking slot, acquire the route, and be directed with high accuracy to the parking slots of their choice. In this study, advanced sensing and communication technologies were used together with the weighted k nearest neighbours algorithm for positioning and wayfinding in order to improve parking guidance accuracy. Based on the experimental results, the proposed system showed a lower average error rate of 1.5 metres in comparison to other positioning techniques, such as GPS, or other similar algorithms for positioning, such as maximum a posteriori, which have shown average errors of 2.3 metres and 3.55 metres, respectively, a potential increase of more than 35% from the previous error rate. Doi: 10.28991/CEJ-2023-09-08-012 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"85 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"90166049","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-015
F. Aneke, Shadi Hanandeh, D. Kalumba
This study is focused on evaluating the factors affecting the performance of fiber-reinforced subgrade under cyclic loading. To achieve the objectives of this study, a series of dynamic triaxial (DT) tests was performed, and the following parameters, such as resilient modulus (MR), number of loading cycles (N), cyclic stress (CS), resilient strain (RS), and stress-strain hysteresis response of both the reinforced and unreinforced subgrades were evaluated. Subsequently, a series of scanning electron microscope (SEM) tests was conducted to track the fiber-soil interfacial bonding after the completion of DT test. The results indicated that N and CS triggered an appreciable decrease in MR with significantly high RS deformation for the unreinforced subgrade. However, reversed responses were noted upon the inclusion of sisal fiber due to fiber-soil adhesion and a high ductility response was portrayed by the reinforced subgrades. A reversed response was significant upon 0.25% and 0.5% fiber inclusion, beyond which the CS resistance slightly decreased. The stress-strain hysteresis loop was observed to increase as the axial strain increased proportionally with an increase in fiber contents, thus causing a significant increase in energy absorption in specimens. The SEM micrograph showed tightly knitted fiber-soil adhesion after the DT test. This study indicated that the reinforced subgrade sustained the CS, N, and improved energy absorption capacity, and MRupon fiber inclusion. Doi: 10.28991/CEJ-2023-09-08-015 Full Text: PDF
{"title":"Evaluation of Factors Affecting the Performance of Fiber-Reinforced Subgrade Soil Characteristics Under Cyclic Loading","authors":"F. Aneke, Shadi Hanandeh, D. Kalumba","doi":"10.28991/cej-2023-09-08-015","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-015","url":null,"abstract":"This study is focused on evaluating the factors affecting the performance of fiber-reinforced subgrade under cyclic loading. To achieve the objectives of this study, a series of dynamic triaxial (DT) tests was performed, and the following parameters, such as resilient modulus (MR), number of loading cycles (N), cyclic stress (CS), resilient strain (RS), and stress-strain hysteresis response of both the reinforced and unreinforced subgrades were evaluated. Subsequently, a series of scanning electron microscope (SEM) tests was conducted to track the fiber-soil interfacial bonding after the completion of DT test. The results indicated that N and CS triggered an appreciable decrease in MR with significantly high RS deformation for the unreinforced subgrade. However, reversed responses were noted upon the inclusion of sisal fiber due to fiber-soil adhesion and a high ductility response was portrayed by the reinforced subgrades. A reversed response was significant upon 0.25% and 0.5% fiber inclusion, beyond which the CS resistance slightly decreased. The stress-strain hysteresis loop was observed to increase as the axial strain increased proportionally with an increase in fiber contents, thus causing a significant increase in energy absorption in specimens. The SEM micrograph showed tightly knitted fiber-soil adhesion after the DT test. This study indicated that the reinforced subgrade sustained the CS, N, and improved energy absorption capacity, and MRupon fiber inclusion. Doi: 10.28991/CEJ-2023-09-08-015 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"4 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82049539","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-02
S. Hermawan, David Bangguna, Edwin Mihardja, Jason Fernaldi, Jescey Edlin Prajogo
Indonesia is an archipelago country with a wealth of marine resources. However, local communities have not optimally utilized the use of natural resources, including those in the coastal zone of Central Sulawesi, Indonesia. This research goal is to identify the potential coastal areas for future development in the coastal zones, such as grouper floating net cage (FNC) culture, seaweed cultivation, and tourism areas. Thus, it is intended to develop the methodology of the hydrodynamic models for decision support systems (DSS) within the analysis hierarchy process. There are a total of 25 parameters criteria to calculate the potential future coastal zone development, including physics, water quality, and zoning properties. This DSS can serve as the foundation for instruction, knowledge, and application in developing rural coastal regions. Because of its breadth, this research endeavor is still ongoing. After calibration and verification, the initial study of the potential area of approximately 98,000 ha indicates that the model meets the accuracy requirement within the range of the root mean square error of approximately 0.184. Then, the outcomes of the hydrodynamic model simulation in DSS can be used as essential information for maritime development at this location. The outcomes demonstrate that the best areas for grouper FNC cultivation, seaweed cultivation, along with marine tourism are 6,163 ha, 91,000 ha, and 9,024 ha, respectively. It is expected that this research will contribute to sustainable future coastal zone development in the vicinity of Central Sulawesi, Indonesia. Doi: 10.28991/CEJ-2023-09-08-02 Full Text: PDF
{"title":"The Hydrodynamic Model Application for Future Coastal Zone Development in Remote Area","authors":"S. Hermawan, David Bangguna, Edwin Mihardja, Jason Fernaldi, Jescey Edlin Prajogo","doi":"10.28991/cej-2023-09-08-02","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-02","url":null,"abstract":"Indonesia is an archipelago country with a wealth of marine resources. However, local communities have not optimally utilized the use of natural resources, including those in the coastal zone of Central Sulawesi, Indonesia. This research goal is to identify the potential coastal areas for future development in the coastal zones, such as grouper floating net cage (FNC) culture, seaweed cultivation, and tourism areas. Thus, it is intended to develop the methodology of the hydrodynamic models for decision support systems (DSS) within the analysis hierarchy process. There are a total of 25 parameters criteria to calculate the potential future coastal zone development, including physics, water quality, and zoning properties. This DSS can serve as the foundation for instruction, knowledge, and application in developing rural coastal regions. Because of its breadth, this research endeavor is still ongoing. After calibration and verification, the initial study of the potential area of approximately 98,000 ha indicates that the model meets the accuracy requirement within the range of the root mean square error of approximately 0.184. Then, the outcomes of the hydrodynamic model simulation in DSS can be used as essential information for maritime development at this location. The outcomes demonstrate that the best areas for grouper FNC cultivation, seaweed cultivation, along with marine tourism are 6,163 ha, 91,000 ha, and 9,024 ha, respectively. It is expected that this research will contribute to sustainable future coastal zone development in the vicinity of Central Sulawesi, Indonesia. Doi: 10.28991/CEJ-2023-09-08-02 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"12 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"77742510","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-08-01DOI: 10.28991/cej-2023-09-08-05
Hasan Ehssan Alobaidi, A. H. Al-Zuhairi
This study aims to compare the response of reinforced concrete (RC) T-beams strengthened with carbon fibre-reinforced polymer (CFRP) composite with that of non-strengthened control beams when subjected to monotonic two-point loading until failure for flexural once and shear again. The experimental programme tested eight RC T-beams, which included two reference beams without strengthening and six strengthened beams. The eight beams were divided into two main groups according to strengthening (flexural and shear). Experimental analysis was performed to study the effect of the CFRP laminate width in the flexural group and the spacing of CFRP U-wrap sheets in the shear group on the ultimate load capacity, load-strain relationship, and load-deflection relationship. Results show that increasing the width of the CFRP laminate in the flexural group improves the ultimate strengths to approximately 9.5%, 35%, and 41% for beams with CFRP laminate widths of 50, 100, and 150 mm, respectively, compared with the reference non-strengthened beam. The stiffness of the beams increases in direct proportion to the width of the CFRP laminate. In the meantime, decreasing the spacing of the CFRP laminate in the shear group increases the ultimate strengths to approximately 13.2%, 17.7%, and 23.5% for beams with CFRP U-wrap sheet spacings of 166, 125, and 100 mm, respectively, compared with the reference non-strengthened beam. Therefore, the spacing of the CFRP sheet is inversely proportional to the stiffness of the beam. Doi: 10.28991/CEJ-2023-09-08-05 Full Text: PDF
{"title":"Structural Strengthening of Insufficiently Designed Reinforced Concrete T-Beams using CFRP Composites","authors":"Hasan Ehssan Alobaidi, A. H. Al-Zuhairi","doi":"10.28991/cej-2023-09-08-05","DOIUrl":"https://doi.org/10.28991/cej-2023-09-08-05","url":null,"abstract":"This study aims to compare the response of reinforced concrete (RC) T-beams strengthened with carbon fibre-reinforced polymer (CFRP) composite with that of non-strengthened control beams when subjected to monotonic two-point loading until failure for flexural once and shear again. The experimental programme tested eight RC T-beams, which included two reference beams without strengthening and six strengthened beams. The eight beams were divided into two main groups according to strengthening (flexural and shear). Experimental analysis was performed to study the effect of the CFRP laminate width in the flexural group and the spacing of CFRP U-wrap sheets in the shear group on the ultimate load capacity, load-strain relationship, and load-deflection relationship. Results show that increasing the width of the CFRP laminate in the flexural group improves the ultimate strengths to approximately 9.5%, 35%, and 41% for beams with CFRP laminate widths of 50, 100, and 150 mm, respectively, compared with the reference non-strengthened beam. The stiffness of the beams increases in direct proportion to the width of the CFRP laminate. In the meantime, decreasing the spacing of the CFRP laminate in the shear group increases the ultimate strengths to approximately 13.2%, 17.7%, and 23.5% for beams with CFRP U-wrap sheet spacings of 166, 125, and 100 mm, respectively, compared with the reference non-strengthened beam. Therefore, the spacing of the CFRP sheet is inversely proportional to the stiffness of the beam. Doi: 10.28991/CEJ-2023-09-08-05 Full Text: PDF","PeriodicalId":53612,"journal":{"name":"Open Civil Engineering Journal","volume":"39 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2023-08-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"80980305","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：