Pub Date : 2015-08-31DOI: 10.1109/TAPENERGY.2015.7229601
M. V. Divya Prabha, P. Seema
A novel topology of forward-flyback power factor correction (PFC) converter with constant on-time control is proposed in this paper. The converter integrates the operation of a forward converter and a flyback converter. It operates either in the forward mode or the flyback mode depending on whether the input is higher or lower than the reflected output voltage to the transformer primary side. This integrated operation ensures that the dead zone problem of ac input current in conventional forward converters is overcome. It works for the universal ac input range and a high power factor is achieved. The proposed converter operates in critical conduction mode in order to achieve zero voltage switching and constant on-time control is applied. To confirm the validity of the proposed converter, simulations have been done using MATLAB/SIMULINK and are presented here.
{"title":"A novel topology of forward-flyback PFC converter with constant on-time control","authors":"M. V. Divya Prabha, P. Seema","doi":"10.1109/TAPENERGY.2015.7229601","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229601","url":null,"abstract":"A novel topology of forward-flyback power factor correction (PFC) converter with constant on-time control is proposed in this paper. The converter integrates the operation of a forward converter and a flyback converter. It operates either in the forward mode or the flyback mode depending on whether the input is higher or lower than the reflected output voltage to the transformer primary side. This integrated operation ensures that the dead zone problem of ac input current in conventional forward converters is overcome. It works for the universal ac input range and a high power factor is achieved. The proposed converter operates in critical conduction mode in order to achieve zero voltage switching and constant on-time control is applied. To confirm the validity of the proposed converter, simulations have been done using MATLAB/SIMULINK and are presented here.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"70 1","pages":"109-113"},"PeriodicalIF":0.0,"publicationDate":"2015-08-31","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"86727305","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-08-31DOI: 10.1109/TAPENERGY.2015.7229625
Sibi Raj P M, M. Rashmi
Pulse Width Modulated (PWM) inverters produce common mode voltage. The common mode voltage will have adverse effect on the motor bearings. Hence the common mode voltage has to be reduced. This paper presents a modified Sinusoidal Pulse Width Modulation (SPWM) scheme in which two complementary modulating inputs are used to generate the pulses for the switches of a two level, three phase inverter to reduce the common mode voltage. The performance of proposed modulation scheme is evaluated and tested for various switching frequencies. With the proposed modulation scheme the phase voltages appears to be three level voltage which helps in reduction of common mode voltage. A comparative study of common mode voltage with both normal and modified SPWM method is also done and the results are presented in this paper.
{"title":"Reduction of common mode voltage in three phase inverter","authors":"Sibi Raj P M, M. Rashmi","doi":"10.1109/TAPENERGY.2015.7229625","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229625","url":null,"abstract":"Pulse Width Modulated (PWM) inverters produce common mode voltage. The common mode voltage will have adverse effect on the motor bearings. Hence the common mode voltage has to be reduced. This paper presents a modified Sinusoidal Pulse Width Modulation (SPWM) scheme in which two complementary modulating inputs are used to generate the pulses for the switches of a two level, three phase inverter to reduce the common mode voltage. The performance of proposed modulation scheme is evaluated and tested for various switching frequencies. With the proposed modulation scheme the phase voltages appears to be three level voltage which helps in reduction of common mode voltage. A comparative study of common mode voltage with both normal and modified SPWM method is also done and the results are presented in this paper.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"5 1","pages":"244-248"},"PeriodicalIF":0.0,"publicationDate":"2015-08-31","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82218542","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229599
D. Ashwin, M. Dixit, S. Ashok, Vinila Chavan
This paper describes the design and simulation of 15 kW, 2 pole, 50 Hz, three phase induction motor to achieve IE4 efficiency level as defined by the International Electrotechnical Commission (IEC). For achieving higher efficiency, the motor is designed, optimized and simulated with copper die-cast rotor and low loss electrical steel. The simulation method is first validated by comparing with the test results of standard IE3 motor. The same simulated model was taken as reference to design the IE4 motor. This design solution having IE4 efficiency is achieved without changing the stator geometry and frame size.
{"title":"Design optimization of 15 kW, 2-pole induction motor to achieve IE4 efficiency level with copper die-casting","authors":"D. Ashwin, M. Dixit, S. Ashok, Vinila Chavan","doi":"10.1109/TAPENERGY.2015.7229599","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229599","url":null,"abstract":"This paper describes the design and simulation of 15 kW, 2 pole, 50 Hz, three phase induction motor to achieve IE4 efficiency level as defined by the International Electrotechnical Commission (IEC). For achieving higher efficiency, the motor is designed, optimized and simulated with copper die-cast rotor and low loss electrical steel. The simulation method is first validated by comparing with the test results of standard IE3 motor. The same simulated model was taken as reference to design the IE4 motor. This design solution having IE4 efficiency is achieved without changing the stator geometry and frame size.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"6 1","pages":"98-102"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"84422173","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229608
P. Sruthi, D. Rajan, M. Pranav
This paper does the simulation of solar cell powered boost converter with resonant snubber. The converter system have a solar photo voltaic module and a closed loop boost converter. The low input from the solar PV module is converted to high level dc voltage by means of the closed loop boost converter. Converter have a 2D-2C-2L resonant snubber. This snubber ensures turn on at ZCS, and turn off at ZVS which will leads to considerable increase in performance. Converter has low complexity. The simulation of the converter for an input voltage of 12V is also presented.
{"title":"Solar powered boost converter with passive snubber","authors":"P. Sruthi, D. Rajan, M. Pranav","doi":"10.1109/TAPENERGY.2015.7229608","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229608","url":null,"abstract":"This paper does the simulation of solar cell powered boost converter with resonant snubber. The converter system have a solar photo voltaic module and a closed loop boost converter. The low input from the solar PV module is converted to high level dc voltage by means of the closed loop boost converter. Converter have a 2D-2C-2L resonant snubber. This snubber ensures turn on at ZCS, and turn off at ZVS which will leads to considerable increase in performance. Converter has low complexity. The simulation of the converter for an input voltage of 12V is also presented.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"8 1","pages":"150-154"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"85648920","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229607
P. Saranya, L. R. Chandran
Lighting system management and optimization have turned into the most important research trend in lighting electronics. Solar LED lighting scheme is a major kind of light sources in the coming decades because of the efficiency concerns and renewable energy utilization. Conventional LED driving circuit is the combination of diode bridge rectifier and input PFC stage. Diode bridge rectifier at the front end of driving circuit will cause reduced conversion efficiency and power factor. This paper deals with reliable lighting scheme which can be supplied from both solar panel and conventional supply. A battery storage unit is also used to store the energy from PV panel and it also reduces the peak loading while it charging from conventional supply. The dc supply from grid connection is obtained by using bridgeless flyback converter which has inherent power factor correction capability. A MATLAB/Simulink model of proposed scheme is developed for validating the theoretical explanation and the relevant results are also discussed.
{"title":"Bridgeless flyback converter for low power lighting application","authors":"P. Saranya, L. R. Chandran","doi":"10.1109/TAPENERGY.2015.7229607","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229607","url":null,"abstract":"Lighting system management and optimization have turned into the most important research trend in lighting electronics. Solar LED lighting scheme is a major kind of light sources in the coming decades because of the efficiency concerns and renewable energy utilization. Conventional LED driving circuit is the combination of diode bridge rectifier and input PFC stage. Diode bridge rectifier at the front end of driving circuit will cause reduced conversion efficiency and power factor. This paper deals with reliable lighting scheme which can be supplied from both solar panel and conventional supply. A battery storage unit is also used to store the energy from PV panel and it also reduces the peak loading while it charging from conventional supply. The dc supply from grid connection is obtained by using bridgeless flyback converter which has inherent power factor correction capability. A MATLAB/Simulink model of proposed scheme is developed for validating the theoretical explanation and the relevant results are also discussed.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"59 1","pages":"144-149"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"72816104","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229627
V. Ramya Chandranadhan, G. Renjini
This paper compares peak and average current mode control of flyback rectifier with bidirectional switch. The control schemes employs an outer voltage feedback loop, which maintains the output voltage as constant and an inner loop, which sense the input current. Average and peak current mode control of flyback rectifier is suitable for obtaining a regulated output voltage with a varying input. Voltage equivalent of input current is averaged by using high gain current error amplifier, which again compared with the reference voltage in the case of average current mode control. But in the case of peak current mode control, peak inductor current has been sensed and this gives rise to many serious problems, including poor noise immunity, a need for slope compensation, and peak-to-average current errors which the inherently low current loop gain cannot correct. Reference voltage is produced by multiplying the rectified input voltage with the error output voltage. These control methods obtain better line and load regulation with the addition of inner current loop compared with voltage mode control. Also the rectified input voltage feedback achieves better input power factor. Conventional flyback rectifier is the inter connection of a diode bridge rectifier in the input side and a flyback converter. In order to obtain a highly efficient flyback rectifier with fewer losses an improved flyback rectifier is introduced. Improved bridgeless flyback rectifier only introduces a switch with common gate drive, a diode and an additional winding in the secondary side. Thus the weight of the converter is not affected with these additional components. Proposed peak and average current mode control can be used as an adapter. Design details of average current mode control also discussed and simulation and hardware results are presented.
{"title":"Comparison between peak and average current mode control of improved bridgeless flyback rectifier with bidirectional switch","authors":"V. Ramya Chandranadhan, G. Renjini","doi":"10.1109/TAPENERGY.2015.7229627","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229627","url":null,"abstract":"This paper compares peak and average current mode control of flyback rectifier with bidirectional switch. The control schemes employs an outer voltage feedback loop, which maintains the output voltage as constant and an inner loop, which sense the input current. Average and peak current mode control of flyback rectifier is suitable for obtaining a regulated output voltage with a varying input. Voltage equivalent of input current is averaged by using high gain current error amplifier, which again compared with the reference voltage in the case of average current mode control. But in the case of peak current mode control, peak inductor current has been sensed and this gives rise to many serious problems, including poor noise immunity, a need for slope compensation, and peak-to-average current errors which the inherently low current loop gain cannot correct. Reference voltage is produced by multiplying the rectified input voltage with the error output voltage. These control methods obtain better line and load regulation with the addition of inner current loop compared with voltage mode control. Also the rectified input voltage feedback achieves better input power factor. Conventional flyback rectifier is the inter connection of a diode bridge rectifier in the input side and a flyback converter. In order to obtain a highly efficient flyback rectifier with fewer losses an improved flyback rectifier is introduced. Improved bridgeless flyback rectifier only introduces a switch with common gate drive, a diode and an additional winding in the secondary side. Thus the weight of the converter is not affected with these additional components. Proposed peak and average current mode control can be used as an adapter. Design details of average current mode control also discussed and simulation and hardware results are presented.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"10 1","pages":"254-259"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"83703745","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229626
Parvathi Nair, K. Deepa
A two port DC-DC converter, combined with a modified flyback inverter, is presented in this paper. The output of the inverter is 230V sinusoidal voltage at 50Hz used for supplying rural lighting applications. Combination (solar and battery) of the energy sources along with a voltage doubler forms the two input port of the DC-DC converter for solar-battery hybrid systems. To obtain a low frequency output voltage for the load modified flyback inverter structure is utilized. A control algorithm implemented to supply the load using PV and battery sources either independently or simultaneously for maintaining the constant output voltage is also presented. This work focuses on simulation studies of the same to verify the converter working using PSIM software.
{"title":"Two-port DC-DC converter with flyback inverter for rural lighting applications","authors":"Parvathi Nair, K. Deepa","doi":"10.1109/TAPENERGY.2015.7229626","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229626","url":null,"abstract":"A two port DC-DC converter, combined with a modified flyback inverter, is presented in this paper. The output of the inverter is 230V sinusoidal voltage at 50Hz used for supplying rural lighting applications. Combination (solar and battery) of the energy sources along with a voltage doubler forms the two input port of the DC-DC converter for solar-battery hybrid systems. To obtain a low frequency output voltage for the load modified flyback inverter structure is utilized. A control algorithm implemented to supply the load using PV and battery sources either independently or simultaneously for maintaining the constant output voltage is also presented. This work focuses on simulation studies of the same to verify the converter working using PSIM software.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"18 1","pages":"249-253"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82490073","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229649
Saketh Dogga, V. Surendar, P. Ponnambalam, M. P. Kumar
The hybrid converter topology presented in this article is called Boost Derived Hybrid Converter (BDHC), it can supply dc and ac loads simultaneously from a single dc input. This topology is realized by replacing the single control switch of a boost converter with an H-bridge inverter. The presented hybrid converter requires lesser number of switches. DC and AC outputs have high reliability, due to its essential shoot-through operation. Better power density and reliability can be well suited for Nano grids in residential applications. A suitable pulse width modulation (PWM) control strategy is devised for BDHC is described in this paper. The implementation of a fuzzy logic controller using output voltage as feedback for significantly improving the performance of BDHC is proposed in this article. The simulation results shows that dc and ac output voltages can be controlled independently in steady state condition of BDHC.
{"title":"Boost Derived Hybrid Converter implementation using fuzzy controller","authors":"Saketh Dogga, V. Surendar, P. Ponnambalam, M. P. Kumar","doi":"10.1109/TAPENERGY.2015.7229649","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229649","url":null,"abstract":"The hybrid converter topology presented in this article is called Boost Derived Hybrid Converter (BDHC), it can supply dc and ac loads simultaneously from a single dc input. This topology is realized by replacing the single control switch of a boost converter with an H-bridge inverter. The presented hybrid converter requires lesser number of switches. DC and AC outputs have high reliability, due to its essential shoot-through operation. Better power density and reliability can be well suited for Nano grids in residential applications. A suitable pulse width modulation (PWM) control strategy is devised for BDHC is described in this paper. The implementation of a fuzzy logic controller using output voltage as feedback for significantly improving the performance of BDHC is proposed in this article. The simulation results shows that dc and ac output voltages can be controlled independently in steady state condition of BDHC.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"99 1","pages":"381-386"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"81066646","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229583
Saakshi Awasthi, S. Nanda
In this paper we consider the problem of estimation of amplitude, phase and frequency of a time-varying sinusoidal signal corrupted by noise. The frequency is estimated using Linear Predictor Approach and amplitude, phase is estimated using ADALINE approach. It is a two stage algorithm, estimated frequency of first stage is used to estimate amplitude and phase in second stage. Moreover, the learning parameter is tuned iteratively for faster convergence. From the proposed method a numerically robust and low complexity algorithm is derived for tracking the parameters of real sinusoid. Simulation results illustrate the good performance of the proposed method.
{"title":"A two stage hybrid algorithm for estimation of non-stationary sinusoidal signal parameter","authors":"Saakshi Awasthi, S. Nanda","doi":"10.1109/TAPENERGY.2015.7229583","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229583","url":null,"abstract":"In this paper we consider the problem of estimation of amplitude, phase and frequency of a time-varying sinusoidal signal corrupted by noise. The frequency is estimated using Linear Predictor Approach and amplitude, phase is estimated using ADALINE approach. It is a two stage algorithm, estimated frequency of first stage is used to estimate amplitude and phase in second stage. Moreover, the learning parameter is tuned iteratively for faster convergence. From the proposed method a numerically robust and low complexity algorithm is derived for tracking the parameters of real sinusoid. Simulation results illustrate the good performance of the proposed method.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"1 1","pages":"1-5"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"90201470","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2015-06-24DOI: 10.1109/TAPENERGY.2015.7229620
Joseph Peter, R. Ramchand
A simple current error space vector (CESV)based constant switching frequency hysteresis controller for two level voltage source inverter fed Induction Motor(IM) drives is proposed in this paper. The main advantages of space phasor based hysteresis controllers such as fast dynamic response, adjacent voltage vector switching can be seen in the proposed controller. In addition to these, switching frequency variation can be eliminated substantially. The stator voltages estimated from the current ripple, calculation of vector switching times and voltage error vectors are used for the current error boundary calculation. The proposed controller selects only those inverter voltage vectors of the present sector which are adjacent to the machine voltage vectors for the entire range of operation to reduce current error. Bus clamping space vector pulse width modulation(BCSVPWM) is used for vector selection logic where only one zero state is used in a sub cycle of total switching time period. The proposed hysteresis controller based inverter fed drive scheme is simulated using SIMULINK toolbox of MATLAB for steady state and transient performance.
{"title":"Constant switching frequency hysteresis controller for VSI fed Induction Motor drive using current error space phasor approach","authors":"Joseph Peter, R. Ramchand","doi":"10.1109/TAPENERGY.2015.7229620","DOIUrl":"https://doi.org/10.1109/TAPENERGY.2015.7229620","url":null,"abstract":"A simple current error space vector (CESV)based constant switching frequency hysteresis controller for two level voltage source inverter fed Induction Motor(IM) drives is proposed in this paper. The main advantages of space phasor based hysteresis controllers such as fast dynamic response, adjacent voltage vector switching can be seen in the proposed controller. In addition to these, switching frequency variation can be eliminated substantially. The stator voltages estimated from the current ripple, calculation of vector switching times and voltage error vectors are used for the current error boundary calculation. The proposed controller selects only those inverter voltage vectors of the present sector which are adjacent to the machine voltage vectors for the entire range of operation to reduce current error. Bus clamping space vector pulse width modulation(BCSVPWM) is used for vector selection logic where only one zero state is used in a sub cycle of total switching time period. The proposed hysteresis controller based inverter fed drive scheme is simulated using SIMULINK toolbox of MATLAB for steady state and transient performance.","PeriodicalId":6552,"journal":{"name":"2015 International Conference on Technological Advancements in Power and Energy (TAP Energy)","volume":"97 1","pages":"217-221"},"PeriodicalIF":0.0,"publicationDate":"2015-06-24","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"85756040","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：