Gels最新文献

The viscoelastic response of carrageenan hydrogels to large amplitude oscillatory shear (LAOS) has not received much attention in the literature in spite of its relevance in industrial application. A set of hybrid carrageenans with differing chemical compositions are gelled in the presence of KCl or NaCl, and their nonlinear viscoelastic responses are systematically compared with mixtures of kappa- and iota-carrageenans of equivalent kappa-carrageenan contents. Two categories of LAOS response are identified: strain softening and strain hardening gels. Strain softening gels show LAOS non-reversibility: when entering the nonlinear viscoelastic regime, the shear storage modulus G' decreases with increasing strain, and never recovers its linear value G₀ after successive LAOS sweeps. In contrast to this, strain hardening carrageenan gels show a certain amount of LAOS reversibility: when entering the nonlinear regime, G' increases with strain and shows a maximum at strain γ_H. For strains applied below γ_H, G₀ shows good reversibility and the strain hardening behavior is maintained. For strains larger than γ_H, G₀ decreases significantly indicating an irreversible structural change in the elastic network. Strain hardening and elastic recovery after LAOS prevail for hybrid carrageenan and iota-carrageenan gels, but are only achieved when blends are gelled in NaCl, suggesting a phase separated structure with a certain degree of co-aggregated interface for mixed gels.

This study evaluated possible utilization of infrared drying (ID) as an alternative to spray- (SD) and freeze-drying (FD) for fish skin-derived gelatins. Physical, functional, thermal, and spectroscopic analyses were conducted for characterization of the resulting gelatin powders. Energy consumption for the applied drying methods were 3.41, 8.46 and 25.33 kWh/kg for ID, SD and FD respectively, indicating that ID had the lowest energy consumption among the studied methods. Gel strength, on the other hand, was lower (398.4 g) in infrared-dried gelatin (ID-FG) compared to that (454.9 g) of freeze-dried gelatin (FD-FG) and that (472.7 g) of spray-dried gelatin (SD-FG). TGA curves indicated that ID-FG showed more resilience to thermal degradation. SDS-PAGE and UV-Vis spectra indicated that slight degradation was observed in the β-configuration of ID-FG. ID-FG and SD-FG gelatins had the highest water holding capacity (WHC), protein solubility and transparency values compared to that of FD-FG. Morphological structures of the samples were quite different as shown by SEM visuals. Ultimately, the findings showed that infrared drying may be a promising alternative for gelatin processing, maintaining product quality and supporting sustainable practices in food and other industries.

Hydrogel features can be designed and optimized using different crosslinking agents to meet specific requirements. In this regard, the present work investigates the physico-chemical features of cellulose-based hydrogels, designed by using different epoxy crosslinkers from the same glycidyl family, namely epichlorohydrin (ECH), 1,4-butanediol diglycidyl ether (BDDE), and trimethylolpropane triglycidyl ether (TMPTGE). The effect of the crosslinker's structure (from simple to branched) and functionality (mono-, bi- and tri-epoxy groups) on the hydrogels' features was studied. The performances of the hydrogels were investigated through the gel fraction, as well as by ATR-FTIR, DVS, SEM, DSC, and TG analyses. Also, the swelling and rheological behaviors of the hydrogels were examined. The advantages and limitations of each approach were discussed and a strong correlation between the crosslinker structure and the hydrogel properties was established. The formation of new ether bonds was evidenced by ATR-FTIR spectroscopy. It was emphasized that the pore size is directly influenced by the crosslinker type, namely, it decreases with the increasing number of epoxy groups from the crosslinker molecule, i.e., from 46 ± 11.1 µm (hydrogel CE, with ECH) to 12.3 ± 2.5 µm (hydrogel CB, with BDDE) and 6.7 ± 1.5 µm (hydrogel CT, with TMPTGE). The rheological behavior is consistent with the swelling data and hydrogel morphology, such as CE with the highest Q_max and the largest pore size being relatively more elastic than CB and CT. Instead, the denser matrices obtained by using crosslinkers with more complex structures have better thermal stability. The experimental results highlight the possibility of using a specific crosslinking agent, with a defined structure and functionality, in order to establish the main characteristics of hydrogels and, implicitly, to design them for a certain field of application.

Polyvinyl alcohol (PVA)/TiO₂/colloidal photonic crystal (CPC) films with photocatalytic properties are presented, where TiO₂ nanoparticles were introduced into the PVA gel network. Such PVA/TiO₂/CPC films possess three-dimensional periodic structures that are supported with a PVA/TiO₂ composite gel. The unique structural color of CPCs can indicate the process of material preparation, adsorption, and desorption. The shift of diffraction peaks of CPCs can be more accurately determined using fiber-optic spectroscopy. The effect of the PVA/TiO₂/CPC catalyst films showed better properties as the degradation of methylene blue (MB) by the PVA/TiO₂/CPC film catalyst in 4 h was 77~90%, while the degradation of MB by the PVA/TiO₂ film was 33% in 4 h, indicating that the photonic crystal structure was 2.3~2.7 times more effective than that of the bulk structure.

A new series of flexible polyamide (PA) aerogels was synthesized using terephthaloyl chloride (TPC), 2,2'-dimethylbenzidine (DMBZ) and cross-linked with an inexpensive, commercially available tri-isocyanate (Desmodur N3300A) at polymer concentrations of 6-8 wt.% total solids and repeating units, n, from 30 to 60. The cross-linked DMBZ-based polyamide aerogels obtained, after supercritically drying using liquid CO₂, had shrinkages of 19-27% with densities ranging from 0.12 g/cm³ to 0.22 g/cm³, porosity and surface areas up to 91% and 309 m²/g, respectively, and modulus values ranging from 20.6 to 109 MPa. Evidence suggests that a higher flexibility could be achieved using DMBZ in the polyamide backbone with N3300A as a cross-linker, when compared to previously reported TPC-mPDA-BTC PA aerogels, N3300A-polyimide aerogels, and N3300-reinforced silica aerogels.

Oil paintings represent significant cultural heritage, as they embody human creativity and historical narratives. The preservation of these invaluable artifacts requires effective maintenance practices to ensure their longevity and integrity. Despite their inherent durability, oil paintings are susceptible to mechanical damage and chemical deterioration, necessitating rigorous conservation efforts. Traditional preservation techniques that have been developed over centuries involve surface treatment, structural stabilization, and gel-based cleaning to maintain both the integrity and aesthetic appeal of these artworks. Recent advances in artificial intelligence (AI)-powered predictive maintenance techniques offer innovative solutions to predict and prevent deterioration. By integrating image analysis and environmental monitoring, AI-based models provide valuable insights into painting preservation. This review comprehensively analyzes traditional and AI-based techniques for oil painting maintenance, highlighting the importance of adopting innovative approaches. By integrating traditional expertise with AI technology, conservators can enhance their capacity to maintain and preserve these cultural treasures for future generations.

We revealed that the encapsulation of enzyme-immobilized silica particles in hollow-type spherical bacterial cellulose (HSBC) gels enables the use of the inside of HSBC gels as a reaction field. The encapsulation of horseradish peroxidase (HRP)-immobilized silica particles (Si-HRPs, particle size: 40-50 μm) within HSBC gels was performed by using a BC gelatinous membrane produced at the interface between Komagataeibacter xylinus suspension attached onto an alginate gel containing Si-HRPs and silicone oil. After the biosynthesis of the BC gelatinous membrane, formed from cellulose nanofiber networks, the alginate gel was removed via immersion in a phosphate-buffered solution. Si-HRP encapsulated HSBC gels were reproducibly produced using our method with a yield of over 90%. The pore size of the network structure of the BC gelatinous membrane was less than 1 μm, which is significantly smaller than the encapsulated Si-HRPs. Consequently, the encapsulated Si-HRPs could neither pass through the BC gelatinous membrane nor leak from the interior cavity of the HSBC gel. The activity of the encapsulated HRPs was detected using the 3,3',5,5'-tetramethylbenzidine (TMB)-H₂O₂ system, demonstrating that this method can encapsulate the enzyme without inactivation. Since HSBC gels are composed of a network structure of biocompatible cellulose nanofibers, immune cells cannot enter the hollow interior, thus, the enzyme-immobilized particles encapsulated inside the HSBC gel are protected from immune-cell attacks. The encapsulation technique demonstrated in this study is expected to facilitate the delivery of enzymes and catalysts that are not originally present in the in vivo environment.

Cell spheroids are an important three-dimensional (3D) model for in vitro testing and are gaining interest for their use in clinical applications. More natural 3D cell culture environments that support cell-cell interactions have been created for cancer drug discovery and therapy applications, such as the scaffold-free 3D Petri Dish^® technology. This technology uses reusable and autoclavable silicone micro-molds with different topographies, and it conventionally uses gelled agarose for hydrogel formation to preserve the topography of the selected micro-mold. The present study investigated the feasibility of using a patterned Poly(vinyl alcohol) hydrogel using the circular topography 12-81 (9 × 9 wells) micro-mold to form HeLa cancer cell spheroids and compare them with the formed spheroids using agarose hydrogels. PVA hydrogels showed a slightly softer, springier, and stickier texture than agarose hydrogels. After preparation, Fourier transform infrared (FTIR) spectra showed chemical interactions through hydrogen bonding in the PVA and agarose hydrogels. Both types of hydrogels favor the formation of large HeLa spheroids with an average diameter of around 700-800 µm after 72 h. However, the PVA spheroids are more compact than those from agarose, suggesting a potential influence of micro-mold surface chemistry on cell behavior and spheroid formation. This was additionally confirmed by evaluating the spheroid size, morphology, integrity, as well as E-cadherin and Ki67 expression. The results suggest that PVA promotes stronger cell-to-cell interactions in the spheroids. Even the integrity of PVA spheroids was maintained after exposure to the drug cisplatin. In conclusion, the patterned PVA hydrogels were successfully prepared using the 3D Petri Dish^® micro-molds, and they could be used as suitable platforms for studying cell-cell interactions in cancer drug therapy.

Overcoming the oxygen diffusion limit of approximately 200 µm remains one of the most significant and intractable challenges to be overcome in tissue engineering. The fabrication of hydrogel microtissues and their assembly into larger structures may provide a solution, though these constructs are not without their own drawbacks; namely, these hydrogels are rapidly degraded in vivo, and cells delivered via microtissues are quickly expelled from the area of action. Here, we report the development of an easily customized protocol for creating a protective, biocompatible hydrogel barrier around microtissues. We show that calcium carbonate nanoparticles embedded within an ECM-based microtissue diffuse outwards and, when then exposed to a solution of alginate, can be used to generate a coated layer around the tissue. We further show that this technique can be fine-tuned by adjusting numerous parameters, granting us full control over the thickness of the hydrogel coating layer. The microtissues' protective hydrogel functioned as hypothesized in both in vitro and in vivo testing by preventing the cells inside the tissue from escaping and protecting the microdroplets against external degradation. This technology may provide microtissues with customized properties for use as sources of regenerative therapies.