H. Oktadinata, Dewin Purnama, Rizal Nurdian Hamzah, Agung Slamet Apriyan
Nodular cast iron possesses a spherical graphite shape and exhibits mechanical properties closely resembling those of steel after heat treatment. The austempering method provides a means of enhancing the mechanical properties of nodular cast iron. This study aimed to investigate the optimal parameter combinations for Austempered Ductile Iron (ADI). The experiments involved varying the austenitization temperature and austempering time. Multiple tests were conducted to analyze the effects of austenitization temperature and tempering time on the microstructure, hardness, and impact toughness. The experimental samples were obtained from Y-block nodular cast iron austenitized at 850, 900, and 950°C for 90 min in an electric furnace. Subsequently, they were quenched in a salt bath at a temperature of 350°C and held for 60, 90, and 120 minutes before being cooled to room temperature. Mechanical tests and microstructure observations were performed on both the as-cast sample and after austempering. The microstructure was observed using an optical microscope before and after the etching. The research findings indicated that austempering increases the hardness and impact toughness of nodular cast iron. The highest hardness (46.8 HRC) was achieved from a parameter combination of an austenitization temperature of 850°C and an austempering time of 90 minutes. This particular sample also exhibited a relatively higher impact energy (3.8 J) compared to the others. The results of this study suggest that the austenitization temperature and tempering time exert an influence on the mechanical properties.
{"title":"A study on optimal parameter combinations for austempered ductile iron","authors":"H. Oktadinata, Dewin Purnama, Rizal Nurdian Hamzah, Agung Slamet Apriyan","doi":"10.30811/jpl.v22i3.5001","DOIUrl":"https://doi.org/10.30811/jpl.v22i3.5001","url":null,"abstract":"Nodular cast iron possesses a spherical graphite shape and exhibits mechanical properties closely resembling those of steel after heat treatment. The austempering method provides a means of enhancing the mechanical properties of nodular cast iron. This study aimed to investigate the optimal parameter combinations for Austempered Ductile Iron (ADI). The experiments involved varying the austenitization temperature and austempering time. Multiple tests were conducted to analyze the effects of austenitization temperature and tempering time on the microstructure, hardness, and impact toughness. The experimental samples were obtained from Y-block nodular cast iron austenitized at 850, 900, and 950°C for 90 min in an electric furnace. Subsequently, they were quenched in a salt bath at a temperature of 350°C and held for 60, 90, and 120 minutes before being cooled to room temperature. Mechanical tests and microstructure observations were performed on both the as-cast sample and after austempering. The microstructure was observed using an optical microscope before and after the etching. The research findings indicated that austempering increases the hardness and impact toughness of nodular cast iron. The highest hardness (46.8 HRC) was achieved from a parameter combination of an austenitization temperature of 850°C and an austempering time of 90 minutes. This particular sample also exhibited a relatively higher impact energy (3.8 J) compared to the others. The results of this study suggest that the austenitization temperature and tempering time exert an influence on the mechanical properties.","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"234 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141708606","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
N. Ilminnafik, Agus Triono, Reynaldi Akbar Ali, Rizal Mahmud, D. Prasetiyo
Indonesia observes a yearly rise in motor vehicle possession. Failure to consider alternate fuels in these trends may result in the depletion of gasoline. Out of the potential alternatives, Liquified Petroleum Gas (LPG) appears to be the most favorable. The sole issue lies in the elevated engine temperature and subsequent decrease in performance caused by its utilization. To address this vulnerability, it is advisable to employ a cooling injection method, such as water injection. Nevertheless, the rise in exhaust emissions linked to water injection highlights the necessity for optimization. This study aims to optimize coolant injection systems by conducting experiments with different modifications, such as conventional intake surfaces, dimple intake surfaces with gaps, and dimple intake surfaces without gaps. The gapless dimple inlet surface demonstrates superior performance in terms of exhaust emissions, power, and torque compared to both conventional inlet surfaces and slotted dimple inlet surfaces
{"title":"Effects of modified intake surface to gasoline engine performance with the use of LPG","authors":"N. Ilminnafik, Agus Triono, Reynaldi Akbar Ali, Rizal Mahmud, D. Prasetiyo","doi":"10.30811/jpl.v22i3.4008","DOIUrl":"https://doi.org/10.30811/jpl.v22i3.4008","url":null,"abstract":"Indonesia observes a yearly rise in motor vehicle possession. Failure to consider alternate fuels in these trends may result in the depletion of gasoline. Out of the potential alternatives, Liquified Petroleum Gas (LPG) appears to be the most favorable. The sole issue lies in the elevated engine temperature and subsequent decrease in performance caused by its utilization. To address this vulnerability, it is advisable to employ a cooling injection method, such as water injection. Nevertheless, the rise in exhaust emissions linked to water injection highlights the necessity for optimization. This study aims to optimize coolant injection systems by conducting experiments with different modifications, such as conventional intake surfaces, dimple intake surfaces with gaps, and dimple intake surfaces without gaps. The gapless dimple inlet surface demonstrates superior performance in terms of exhaust emissions, power, and torque compared to both conventional inlet surfaces and slotted dimple inlet surfaces","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"9 5","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141701874","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Z. Emzain, Zean Galang Wardhana, Satworo Adiwidodo, Siti Duratun Nasiqiati Rosady, Prasetyo Prasetyo, Muhammad Andi Nova
A centrifugal pump is an essential mechanical device in the Regional Drinking Water Company (PDAM) to distribute sterile water from the reservoir to local community houses by flowing the fluid through the pipeline. However, improper and inadequate maintenance of centrifugal pumps can result in component damage, including bearings that are broken, ripped, or damaged mechanical seals. Therefore, for the water supply to continue smoothly, proper maintenance needs to be carried out so that the engine's performance will be maintained and last longer. This study aims to conduct a maintenance analysis on centrifugal pumps utilized by the PDAM of Madiun City. The Failure Modes and Effects Analysis (FMEA) method was employed to assess the potential failure of a system, design, process, or service by implementing a systematic approach to analyze damage and devise maintenance strategies. The FMEA analysis revealed that the shaft of the centrifugal pump component had the highest Risk Priority Number (RPN) value, which amounts to 294. The wearing ring had the lowest RPN value among the centrifugal pump components, with a value of 54. The Pareto diagram results classified six components: shaft, clutch, stuffing box, motor, impeller, and mechanical seal to recommend preventative maintenance action. Additionally, three other components suggested for corrective maintenance were the bearing, packing, and wearing rings
{"title":"Implementation of Failure Mode and Effect Analysis (FMEA) for centrifugal pump maintenance in water supply distribution system","authors":"Z. Emzain, Zean Galang Wardhana, Satworo Adiwidodo, Siti Duratun Nasiqiati Rosady, Prasetyo Prasetyo, Muhammad Andi Nova","doi":"10.30811/jpl.v22i3.4739","DOIUrl":"https://doi.org/10.30811/jpl.v22i3.4739","url":null,"abstract":"A centrifugal pump is an essential mechanical device in the Regional Drinking Water Company (PDAM) to distribute sterile water from the reservoir to local community houses by flowing the fluid through the pipeline. However, improper and inadequate maintenance of centrifugal pumps can result in component damage, including bearings that are broken, ripped, or damaged mechanical seals. Therefore, for the water supply to continue smoothly, proper maintenance needs to be carried out so that the engine's performance will be maintained and last longer. This study aims to conduct a maintenance analysis on centrifugal pumps utilized by the PDAM of Madiun City. The Failure Modes and Effects Analysis (FMEA) method was employed to assess the potential failure of a system, design, process, or service by implementing a systematic approach to analyze damage and devise maintenance strategies. The FMEA analysis revealed that the shaft of the centrifugal pump component had the highest Risk Priority Number (RPN) value, which amounts to 294. The wearing ring had the lowest RPN value among the centrifugal pump components, with a value of 54. The Pareto diagram results classified six components: shaft, clutch, stuffing box, motor, impeller, and mechanical seal to recommend preventative maintenance action. Additionally, three other components suggested for corrective maintenance were the bearing, packing, and wearing rings","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"45 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141715236","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Nowadays, the demand for workers in the agriculture industry has decreased and there is a need for rising mechanization in the agriculture process. The agriculture process that requires mechanization is cultivating. The rice cultivator has to be as light as possible, so requires a lighter material but is also strong enough. The correlation between the rice transplanter tool and the wheels is closely related to soil conditions. The selection of wheel materials is considered based on the characteristics of the planting area. In addition, another influence variable is the angle of the fin in the rice transplanter wheel. Material of rice transplanter wheel has been established, these are 1023 carbon steel sheet, AISI 1020 steel cold rolled, AISI 316 stainless steel. The angle of the fin was varied, these are 30, 35, and 40, this fin will give an effect on the traction result of rice transplanter wheel movement. The combination of lightweight material and the appropriate fin angle of the rice transplanter wheel has the best traction result. As a result of this research, the suitable material for the rice transplanter wheel was carbon steel and the fin’s angle was 30. This research involved a comparison and analysis of material strength under various fin angles. The evaluation of stress criteria was conducted using design values to determine the most reliable final product design. The paper contributes by illustrating how to represent the final decision on the combination of design and materials, incorporating a cost index assessment.
{"title":"Performance materials with variations of tractor drive wheel fin angle and low-cost manufacturing analysis","authors":"Sherly Octavia Saraswati, Endra Dwi Purnomo, Amiruddin Aziz, C. Nandar, Setyo Margo Utomo, Marsalyna Marsalyna, Fandy Septian Nugroho, Lia Amelia, Achmad Ridho Mubarak, Lambert Hotma","doi":"10.30811/jpl.v22i3.4649","DOIUrl":"https://doi.org/10.30811/jpl.v22i3.4649","url":null,"abstract":"Nowadays, the demand for workers in the agriculture industry has decreased and there is a need for rising mechanization in the agriculture process. The agriculture process that requires mechanization is cultivating. The rice cultivator has to be as light as possible, so requires a lighter material but is also strong enough. The correlation between the rice transplanter tool and the wheels is closely related to soil conditions. The selection of wheel materials is considered based on the characteristics of the planting area. In addition, another influence variable is the angle of the fin in the rice transplanter wheel. Material of rice transplanter wheel has been established, these are 1023 carbon steel sheet, AISI 1020 steel cold rolled, AISI 316 stainless steel. The angle of the fin was varied, these are 30, 35, and 40, this fin will give an effect on the traction result of rice transplanter wheel movement. The combination of lightweight material and the appropriate fin angle of the rice transplanter wheel has the best traction result. As a result of this research, the suitable material for the rice transplanter wheel was carbon steel and the fin’s angle was 30. This research involved a comparison and analysis of material strength under various fin angles. The evaluation of stress criteria was conducted using design values to determine the most reliable final product design. The paper contributes by illustrating how to represent the final decision on the combination of design and materials, incorporating a cost index assessment.","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"13 2","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141697006","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The manufacturing sector is constantly seeking ways to optimize the machining process, specifically for 3-axis CNC machines. This study aims to identify the optimal parameter values that result in the lowest roughness and the highest process capability in 3-axis CNC milling. The roughness level (Ra) of the product is primarily influenced by factors such as feed rate, spindle speed, and depth of cut. Additionally, the reliability of the machining process was analyzed to evaluate its ability to consistently achieve low roughness values and to validate the process capability of the VH850L3 series 3-axis CNC milling machine. The suggested approach for this analysis was the RSM central composite design method, which involved conducting experiments under various input conditions. The results indicated that the feed rate had the most significant impact on roughness, followed by the spindle speed, while the depth of cut had no effect. The parameters that resulted in the lowest roughness response were a spindle speed of 2589.76 rpm, a depth of cut of 0.159 mm, and a feed rate of 247.731 mm/min. These parameter values were tested on a 3-axis CNC machine, and the resulting data exhibited variations. Data processing revealed that the machine still performed optimally in the machining process, as indicated by the value of . However, the milling process deviates from the standard target, as the response value shows significant variation with a Cpk value 1.
{"title":"Optimization of CNC milling parameters using the response surface method for aluminum 6061","authors":"Arifin Indaka, Bagus Wahyudi","doi":"10.30811/jpl.v22i3.4909","DOIUrl":"https://doi.org/10.30811/jpl.v22i3.4909","url":null,"abstract":"The manufacturing sector is constantly seeking ways to optimize the machining process, specifically for 3-axis CNC machines. This study aims to identify the optimal parameter values that result in the lowest roughness and the highest process capability in 3-axis CNC milling. The roughness level (Ra) of the product is primarily influenced by factors such as feed rate, spindle speed, and depth of cut. Additionally, the reliability of the machining process was analyzed to evaluate its ability to consistently achieve low roughness values and to validate the process capability of the VH850L3 series 3-axis CNC milling machine. The suggested approach for this analysis was the RSM central composite design method, which involved conducting experiments under various input conditions. The results indicated that the feed rate had the most significant impact on roughness, followed by the spindle speed, while the depth of cut had no effect. The parameters that resulted in the lowest roughness response were a spindle speed of 2589.76 rpm, a depth of cut of 0.159 mm, and a feed rate of 247.731 mm/min. These parameter values were tested on a 3-axis CNC machine, and the resulting data exhibited variations. Data processing revealed that the machine still performed optimally in the machining process, as indicated by the value of . However, the milling process deviates from the standard target, as the response value shows significant variation with a Cpk value 1.","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"71 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-07-01","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"141696277","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
An industry requires a cooling medium to reduce heat in an industrial machine during operation. Companies generally use cooling towers for engine cooling media. The common issue is that heat reduction and heat transfer rate are not significant. Therefore, a new variation is needed to ensure that the cooling tower can effectively lower the temperature of the machinery. The problem statement aims to determine the parameters that can enhance both the heat transfer rate and the heat transfer coefficient in cooling towers. The objective is to determine the heat transfer rate and heat transfer coefficient. The method used is experimental by varying the water inlet in five variations of the cooling tower plates, they are being 48, 60, 80, 120, and 250 holes. The results showed that the highest temperature difference occurs at Tin 80oC with the variation of 250 holes, which is 9.34oC, and the highest heat transfer value reached 1833.17 watts. Meanwhile, the lowest temperature difference occurred at Tin 60oC with a variation of 48 holes, which is 3,98oC, and the lowest heat transfer value reached 787.47 watts. The highest convection coefficient occurs at Tin 70oC with the variation of 250 holes, which is 117.74 W/m²⋅K. The lowest convection coefficient occurs at Tin 80oC with a variation of 48 holes, which is 77.36 W/m²⋅K. This can be concluded that the temperature difference (⧍T), heat transfer rate, and heat transfer coefficient will increase when the number of holes in each plate variation increases.
{"title":"Effect of numerous plate holes in a cooling tower on heat transfer optimization","authors":"Heli Suansyah, Ahmad Syuhada, Sarwo Edhy Sofyan","doi":"10.30811/jpl.v21i5.4069","DOIUrl":"https://doi.org/10.30811/jpl.v21i5.4069","url":null,"abstract":"An industry requires a cooling medium to reduce heat in an industrial machine during operation. Companies generally use cooling towers for engine cooling media. The common issue is that heat reduction and heat transfer rate are not significant. Therefore, a new variation is needed to ensure that the cooling tower can effectively lower the temperature of the machinery. The problem statement aims to determine the parameters that can enhance both the heat transfer rate and the heat transfer coefficient in cooling towers. The objective is to determine the heat transfer rate and heat transfer coefficient. The method used is experimental by varying the water inlet in five variations of the cooling tower plates, they are being 48, 60, 80, 120, and 250 holes. The results showed that the highest temperature difference occurs at Tin 80oC with the variation of 250 holes, which is 9.34oC, and the highest heat transfer value reached 1833.17 watts. Meanwhile, the lowest temperature difference occurred at Tin 60oC with a variation of 48 holes, which is 3,98oC, and the lowest heat transfer value reached 787.47 watts. The highest convection coefficient occurs at Tin 70oC with the variation of 250 holes, which is 117.74 W/m²⋅K. The lowest convection coefficient occurs at Tin 80oC with a variation of 48 holes, which is 77.36 W/m²⋅K. This can be concluded that the temperature difference (⧍T), heat transfer rate, and heat transfer coefficient will increase when the number of holes in each plate variation increases.","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"92 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-10-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136132447","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Cooking, a fundamental human necessity, frequently relies on environmentally harmful energy sources. Concentrated solar power offers a promising solution through solar cookers to address this issue. This study assesses a Parabolic Trough Collector (PTC) solar cooker's performance with two reflector materials: chrome stickers and glass mirrors. The PTC-type solar cooker comprises essential components, including an absorber tube, a flexible conduit, and a spiral-shaped cooking container holder that accommodates a diverse range of cooking vessels. In the configuration of the PTC collector, reflectors fabricated from chrome stickers and glass mirrors are strategically employed to harness and concentrate solar radiation effectively. The absorber tube, crafted from copper, is filled with a heat-transfer fluid consisting of soya oil. Experimental investigations were conducted in a two-stage process, encompassing trials without any applied load and subsequently with varying loads. In the no-load experiments, alterations were made to the PTC collector's inclination angle, spanning the ranges of 15º, 20º, 25º, and 30º. In contrast, the load-bearing tests encompassed the assessment of the PTC solar cooker's performance under a diverse array of cooking scenarios, including boiling water, heating oil, frying eggs, and crisping crackers. The evaluated parameters encompassed key metrics such as incident solar radiation (Ir), ambient temperature (Ta), receiver temperature (Tr), fluid temperature (Tf), spiral furnace temperature (Tsf), and load temperature (To). Subsequently, the outcomes of the experiments were employed to determine the efficiency of the solar cooker. Analysis of the no-load test results indicates that the most favorable performance, as observed in the parameters Tr, Tf, and Tsf, is achieved at a collector inclination angle of 15º for both chrome sticker and glass mirror reflector materials. The solar cooker demonstrated commendable proficiency in boiling water, heating oil, frying eggs, and crisping crackers, accomplishing these tasks within a time frame ranging from 5 to 20 minutes. Notably, the solar cooker featuring the glass mirror reflector exhibited a superior thermal efficiency of 33.7%, surpassing the efficiency of the counterpart with the chrome sticker reflector, which registered an efficiency of 30.9%. These findings underscore the efficacy of the glass mirror reflector in harnessing solar energy for enhanced cooking performance within this solar cooker configuration.
{"title":"An experimental study on parabolic trough solar cookers with materials collector of chrome stickers and glass mirrors","authors":"Muhammad Amin, Teuku Azuar Rizal, Fazri Amir","doi":"10.30811/jpl.v21i5.4521","DOIUrl":"https://doi.org/10.30811/jpl.v21i5.4521","url":null,"abstract":"Cooking, a fundamental human necessity, frequently relies on environmentally harmful energy sources. Concentrated solar power offers a promising solution through solar cookers to address this issue. This study assesses a Parabolic Trough Collector (PTC) solar cooker's performance with two reflector materials: chrome stickers and glass mirrors. The PTC-type solar cooker comprises essential components, including an absorber tube, a flexible conduit, and a spiral-shaped cooking container holder that accommodates a diverse range of cooking vessels. In the configuration of the PTC collector, reflectors fabricated from chrome stickers and glass mirrors are strategically employed to harness and concentrate solar radiation effectively. The absorber tube, crafted from copper, is filled with a heat-transfer fluid consisting of soya oil. Experimental investigations were conducted in a two-stage process, encompassing trials without any applied load and subsequently with varying loads. In the no-load experiments, alterations were made to the PTC collector's inclination angle, spanning the ranges of 15º, 20º, 25º, and 30º. In contrast, the load-bearing tests encompassed the assessment of the PTC solar cooker's performance under a diverse array of cooking scenarios, including boiling water, heating oil, frying eggs, and crisping crackers. The evaluated parameters encompassed key metrics such as incident solar radiation (Ir), ambient temperature (Ta), receiver temperature (Tr), fluid temperature (Tf), spiral furnace temperature (Tsf), and load temperature (To). Subsequently, the outcomes of the experiments were employed to determine the efficiency of the solar cooker. Analysis of the no-load test results indicates that the most favorable performance, as observed in the parameters Tr, Tf, and Tsf, is achieved at a collector inclination angle of 15º for both chrome sticker and glass mirror reflector materials. The solar cooker demonstrated commendable proficiency in boiling water, heating oil, frying eggs, and crisping crackers, accomplishing these tasks within a time frame ranging from 5 to 20 minutes. Notably, the solar cooker featuring the glass mirror reflector exhibited a superior thermal efficiency of 33.7%, surpassing the efficiency of the counterpart with the chrome sticker reflector, which registered an efficiency of 30.9%. These findings underscore the efficacy of the glass mirror reflector in harnessing solar energy for enhanced cooking performance within this solar cooker configuration.","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"92 3","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-10-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136132445","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Richard A.M. Napitupulu, Siwan E.A. Peranginangin, Parulian Siagian
One solution that can be taken to reduce GHG emissions is to reduce consumption of fossil fuels and replace them with renewable energy sources. Indonesia is rich in renewable energy sources, and one that has potential to be developed is solar energy. In line with Indonesia's development into a developed country, energy consumption is increasing. One of the activities that contributes to the largest energy use is cooking. The need for energy for cooking in Indonesia is large because the population and households are very large, No. 4 in the world. Solar Cooker is an alternative to reduce the use of fossil or traditional energy for cooking activities. Previous research has shown how the performance of a Solar Cooker can be improved if it is integrated with PCM thermal energy storage, making it possible to speed up cooking time, cook with low solar intensity and even make it possible to cook at night. However, the quantitative influence of the number of PCMs in a solar cooker has not been specifically explained or studied. A low quantity of PCM results in reduced performance, while a high quantity will increase the thermal load, and thus overheating. This research tested 4 units of Simple Tube type Solar Cooker with different quantities of PCM for each unit. From the results of testing the Solar Cooker with the PCM thermal Energy Storage TEST with variations in PCM volume, it showed performance in storing heat for longer even in conditions of high rainfall day and night conditions. This is shown from all observation results during the 6 days of the experiment. As evidenced by the low ambient air temperature and high humidity, especially at night, the temperature drop in the cooking vessel water is quite low. This applies to every variant. From the experimental results, it can also be seen that variants number 1 and 3, especially number 3, have quite good performance, in absorbing heat and storing heat with an outer diameter of 350 mm
{"title":"Experimental Test of the Effect of PCM Volume as Thermal Energy Storage Solar Power in Solar Cooking Units","authors":"Richard A.M. Napitupulu, Siwan E.A. Peranginangin, Parulian Siagian","doi":"10.30811/jpl.v21i5.4266","DOIUrl":"https://doi.org/10.30811/jpl.v21i5.4266","url":null,"abstract":"One solution that can be taken to reduce GHG emissions is to reduce consumption of fossil fuels and replace them with renewable energy sources. Indonesia is rich in renewable energy sources, and one that has potential to be developed is solar energy. In line with Indonesia's development into a developed country, energy consumption is increasing. One of the activities that contributes to the largest energy use is cooking. The need for energy for cooking in Indonesia is large because the population and households are very large, No. 4 in the world. Solar Cooker is an alternative to reduce the use of fossil or traditional energy for cooking activities. Previous research has shown how the performance of a Solar Cooker can be improved if it is integrated with PCM thermal energy storage, making it possible to speed up cooking time, cook with low solar intensity and even make it possible to cook at night. However, the quantitative influence of the number of PCMs in a solar cooker has not been specifically explained or studied. A low quantity of PCM results in reduced performance, while a high quantity will increase the thermal load, and thus overheating. This research tested 4 units of Simple Tube type Solar Cooker with different quantities of PCM for each unit. From the results of testing the Solar Cooker with the PCM thermal Energy Storage TEST with variations in PCM volume, it showed performance in storing heat for longer even in conditions of high rainfall day and night conditions. This is shown from all observation results during the 6 days of the experiment. As evidenced by the low ambient air temperature and high humidity, especially at night, the temperature drop in the cooking vessel water is quite low. This applies to every variant. From the experimental results, it can also be seen that variants number 1 and 3, especially number 3, have quite good performance, in absorbing heat and storing heat with an outer diameter of 350 mm","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"36 1","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-10-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136132451","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Print parameters are factors that influence the mechanical strength of 3D printed objects. Based on a literature review, the parameters of layer thickness, printing speed, and fill geometry percentage value influence the mechanical strength of 3D printed objects. This study focuses on a combination of robust 3D printing parameters for designing CNC router machine gears. The purpose of this research was to determine the effect of printing parameters on the mechanical strength of tensile loads on 3D printed objects. From the experimental results, it was found that by providing a combination of layer thickness parameters, printing speed parameters, and fill percentage parameters, it has an effect on the mechanical strength resistance of 3D printed objects to accept tensile loads. From the research it was found that the ideal layer thickness parameter of 0.1 to 0.2 mm does not exceed half the size of the nozzle diameter of 0.4 mm to produce fine raster fibers. From the research it was found that the ideal speed parameter for printing gears with ABS filament material is at speed 30 mm/s to 50 mm/s to produce a stable raster fiber size and the percentage parameter of a good fill for printing gears is at a value of 20% to 40%. The results of the research found the best printing parameters for printing gears with a print parameter formula with a 3D print parameter formula layer height 0.15mm, gyroid infill 20%, with a speed of 30mm/s maximum tensile strength reaching 30.7 MPa with the results of wheel loading simulation analysis gear is able to withstand a maximum workload of 85 Kg
{"title":"The effect of 3D printing parameters on the tensile strength of acrylonitrile butadiene styrene filament for designing CNC router machine gears","authors":"LAZUARDI LAZUARDI","doi":"10.30811/jpl.v21i5.4045","DOIUrl":"https://doi.org/10.30811/jpl.v21i5.4045","url":null,"abstract":"Print parameters are factors that influence the mechanical strength of 3D printed objects. Based on a literature review, the parameters of layer thickness, printing speed, and fill geometry percentage value influence the mechanical strength of 3D printed objects. This study focuses on a combination of robust 3D printing parameters for designing CNC router machine gears. The purpose of this research was to determine the effect of printing parameters on the mechanical strength of tensile loads on 3D printed objects. From the experimental results, it was found that by providing a combination of layer thickness parameters, printing speed parameters, and fill percentage parameters, it has an effect on the mechanical strength resistance of 3D printed objects to accept tensile loads. From the research it was found that the ideal layer thickness parameter of 0.1 to 0.2 mm does not exceed half the size of the nozzle diameter of 0.4 mm to produce fine raster fibers. From the research it was found that the ideal speed parameter for printing gears with ABS filament material is at speed 30 mm/s to 50 mm/s to produce a stable raster fiber size and the percentage parameter of a good fill for printing gears is at a value of 20% to 40%. The results of the research found the best printing parameters for printing gears with a print parameter formula with a 3D print parameter formula layer height 0.15mm, gyroid infill 20%, with a speed of 30mm/s maximum tensile strength reaching 30.7 MPa with the results of wheel loading simulation analysis gear is able to withstand a maximum workload of 85 Kg","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"12 3","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-10-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136133448","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The development of environmentally friendly composites from natural fibers is an absolute thing to do to replace non-degradable synthetic composites. Some of the weaknesses of natural fiber composites are low mechanical strength, ease of cracking, no moisture resistance, and high-temperature resistance. One of the things that has been done is to make a combination of synthetic materials as a matrix derived from unsaturated polyester reinforced with natural fibers from crushed rice husk particles and starch from sago flour which is used to reduce the percentage of synthetic materials to be able to form composites that are easily decomposed. From the research, it was found that the strength of crack resistance could be increased with a mixture of polyester reinforced with rice husk fiber and sago flour, obtaining an increase in crack resistance strength until the addition of rice husk with a percentage of 15%. While increasing the RH content above 15%, the crack strength value decreases due to the saturation of the RH molecules in the UP which is no longer bound to the UP molecules. The highest crack strength values occurred for the addition of the percentage of RH and SS to the UP material with the addition of 5% SS, which obtained a cracking force of 550 N while the strength of pure polyester was only 37 N. This shows that RH and SS materials can bond with UP molecules and some molecules of RH and SS can prevent cross-linking of polyester molecules. Meanwhile, the addition of SS up to 10% decreases the fracture force obtained, indicating that not all of the sago starch can bind to the polyester molecules.
{"title":"Study of Improved Crack Toughness of Unsaturated Polymers with Rice Husk Fiber and Sago Flour as Strengthening Materials","authors":"nusyirwan nusyirwan","doi":"10.30811/jpl.v21i5.3375","DOIUrl":"https://doi.org/10.30811/jpl.v21i5.3375","url":null,"abstract":"The development of environmentally friendly composites from natural fibers is an absolute thing to do to replace non-degradable synthetic composites. Some of the weaknesses of natural fiber composites are low mechanical strength, ease of cracking, no moisture resistance, and high-temperature resistance. One of the things that has been done is to make a combination of synthetic materials as a matrix derived from unsaturated polyester reinforced with natural fibers from crushed rice husk particles and starch from sago flour which is used to reduce the percentage of synthetic materials to be able to form composites that are easily decomposed. From the research, it was found that the strength of crack resistance could be increased with a mixture of polyester reinforced with rice husk fiber and sago flour, obtaining an increase in crack resistance strength until the addition of rice husk with a percentage of 15%. While increasing the RH content above 15%, the crack strength value decreases due to the saturation of the RH molecules in the UP which is no longer bound to the UP molecules. The highest crack strength values occurred for the addition of the percentage of RH and SS to the UP material with the addition of 5% SS, which obtained a cracking force of 550 N while the strength of pure polyester was only 37 N. This shows that RH and SS materials can bond with UP molecules and some molecules of RH and SS can prevent cross-linking of polyester molecules. Meanwhile, the addition of SS up to 10% decreases the fracture force obtained, indicating that not all of the sago starch can bind to the polyester molecules.","PeriodicalId":166128,"journal":{"name":"Jurnal POLIMESIN","volume":"92 7","pages":"0"},"PeriodicalIF":0.0,"publicationDate":"2023-10-30","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"136132441","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：