Pub Date : 2023-12-21DOI: 10.37763/wr.1336-4561/68.4.768780
Abdurrahman Karaman, Mehmet NURİ YILDIRIM
The objective of this study was to evaluate the effects of selected parameters, such as type of loading (compression and tension), the wooden dowel species, and the adhesives type on the joint stiffness. Beech, oak, and Scots pine woods were used as wooden dowel material, and polyvinylacetate (PVAc) and polyurethane (PUR) adhesives were used as adhesive agents. Elastic stiffness on diagonal tension and compression tests were applied on 120 pieces of test samples prepared. The results showed that there was found out that the highest average elastic stiffness value of 656 Nm/rad was achieved in the oak dowel joints bonded with PVAc adhesive under compression loading. The lowest average value of 293 Nm/rad was found in the Scots pine dowel joints subjected to compression stress using PUR adhesive. On average, the elastic stiffness of the oak dowel joints bonded with PVAc adhesive was 17% higher than the elastic stiffness of the Scots pine dowel joints bonded with PUR adhesive. The influence of the wooden dowel species and the adhesive type were found statistically significant.
{"title":"EFFECT OF MATERIAL, ADHESIVE AND LOADING ON THE STIFFNESS OF WOODEN DOWEL JOINTS","authors":"Abdurrahman Karaman, Mehmet NURİ YILDIRIM","doi":"10.37763/wr.1336-4561/68.4.768780","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.4.768780","url":null,"abstract":"The objective of this study was to evaluate the effects of selected parameters, such as type of loading (compression and tension), the wooden dowel species, and the adhesives type on the joint stiffness. Beech, oak, and Scots pine woods were used as wooden dowel material, and polyvinylacetate (PVAc) and polyurethane (PUR) adhesives were used as adhesive agents. Elastic stiffness on diagonal tension and compression tests were applied on 120 pieces of test samples prepared. The results showed that there was found out that the highest average elastic stiffness value of 656 Nm/rad was achieved in the oak dowel joints bonded with PVAc adhesive under compression loading. The lowest average value of 293 Nm/rad was found in the Scots pine dowel joints subjected to compression stress using PUR adhesive. On average, the elastic stiffness of the oak dowel joints bonded with PVAc adhesive was 17% higher than the elastic stiffness of the Scots pine dowel joints bonded with PUR adhesive. The influence of the wooden dowel species and the adhesive type were found statistically significant.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-12-21","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"138953510","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.425443
S. Augustina, W. Dwianto, Muhammad Adly Rahandi Lubis, R. Damayanti, Danang SUDARWOKO ADI, J. Malik, I. Wahyudi, W. Darmawan, P. Gérardin, S. D. Marbun, H. Isoda
This research deals with low molecular weight-phenol formaldehyde (LMW–PF) impregnation on sepetir (Sindora spp), nyatoh (Palaquium spp.), and pisang putih (Mezzettia spp.) woods to determine the effect of different anatomical structure on weight percent gain and dimensional stability improvement. The wood samples were impregnated using LMW–PF solutions with 7, 8, 9, 10, and 11% of concentrations (w/w), vacuum-pressured (–98 kPa, 15 min, 350 kPa, 4 h), and re-immersed in 80°C for 3 h. According to the findings, LMW–PF impregnation reduced coefficient of swelling by 9.64–29.95%, and increased anti-swelling efficiency by 12.24–29.91%. Additionally, the water absorption and thickness swelling reduced by 2.43–38.75% and 15.94–34.21%, respectively, indicating the improvement of dimensional stability. Microscopy and NIR analysis revealed the presence and reaction of LMW–PF within porous wood matrix. The effect of diverse anatomical structures caused complexity on LMW–PF impregnation. Sepetir-treated wood with fewer anatomical barriers resulted in better dimensional stability improvement than others.
{"title":"EFFECT OF ANATOMICAL STRUCTURE ON DIMENSIONAL STABILITY OF LOW MOLECULAR WEIGHT PHENOL-FORMALDEHYDE IMPREGNATED WOOD","authors":"S. Augustina, W. Dwianto, Muhammad Adly Rahandi Lubis, R. Damayanti, Danang SUDARWOKO ADI, J. Malik, I. Wahyudi, W. Darmawan, P. Gérardin, S. D. Marbun, H. Isoda","doi":"10.37763/wr.1336-4561/68.3.425443","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.425443","url":null,"abstract":"This research deals with low molecular weight-phenol formaldehyde (LMW–PF) impregnation on sepetir (Sindora spp), nyatoh (Palaquium spp.), and pisang putih (Mezzettia spp.) woods to determine the effect of different anatomical structure on weight percent gain and dimensional stability improvement. The wood samples were impregnated using LMW–PF solutions with 7, 8, 9, 10, and 11% of concentrations (w/w), vacuum-pressured (–98 kPa, 15 min, 350 kPa, 4 h), and re-immersed in 80°C for 3 h. According to the findings, LMW–PF impregnation reduced coefficient of swelling by 9.64–29.95%, and increased anti-swelling efficiency by 12.24–29.91%. Additionally, the water absorption and thickness swelling reduced by 2.43–38.75% and 15.94–34.21%, respectively, indicating the improvement of dimensional stability. Microscopy and NIR analysis revealed the presence and reaction of LMW–PF within porous wood matrix. The effect of diverse anatomical structures caused complexity on LMW–PF impregnation. Sepetir-treated wood with fewer anatomical barriers resulted in better dimensional stability improvement than others.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"48415317","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.465476
Qiaofang Zhou, Dongdong Liang, Aokai Cheng, Xianju Wang, Dengyun Tu
Process parameters play an important role in wood surface densification. In this study, the poplar (Populus tomentosa Carr.) wood was heated on one side at 100℃, 150℃ and 180℃, and compressed in the radial direction with the speed of 10 mm/min. The initial thickness of the wood samples were 30 mm, 26 mm and 23 mm, and they were all compressed to 20 mm and resulting in three different compression ratios: 33.3%, 23.1% and 13.0%. When the surface densification completed, the density distribution and hardness of the densified and un-treated samples were measured and analyzed. Results show that the compressing temperature mainly decided the formation of the density distribution curve and the peak density increased with the increasing temperature; as the compression ratio increased, the peak density increased and the thickness of the densified zone broadened; the surface hardness was highly correlated with the density distribution which was affected by temperature and compression ratio, and as the peak density increased and the thickness of the densified broadened the hardness increased accordingly. Therefore, by optimizing the process parameters such as the compressing temperature and compression ratio could generate a targeted density distribution which has the desired hardness.
{"title":"EFFECTS OF PRESSING TEMPERATURE AND COMPRESSION RATIO ON DENSITY DISTRIBUTION AND HARDNESS OF SURFACE DENSIFIED POPLAR WOOD","authors":"Qiaofang Zhou, Dongdong Liang, Aokai Cheng, Xianju Wang, Dengyun Tu","doi":"10.37763/wr.1336-4561/68.3.465476","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.465476","url":null,"abstract":"Process parameters play an important role in wood surface densification. In this study, the poplar (Populus tomentosa Carr.) wood was heated on one side at 100℃, 150℃ and 180℃, and compressed in the radial direction with the speed of 10 mm/min. The initial thickness of the wood samples were 30 mm, 26 mm and 23 mm, and they were all compressed to 20 mm and resulting in three different compression ratios: 33.3%, 23.1% and 13.0%. When the surface densification completed, the density distribution and hardness of the densified and un-treated samples were measured and analyzed. Results show that the compressing temperature mainly decided the formation of the density distribution curve and the peak density increased with the increasing temperature; as the compression ratio increased, the peak density increased and the thickness of the densified zone broadened; the surface hardness was highly correlated with the density distribution which was affected by temperature and compression ratio, and as the peak density increased and the thickness of the densified broadened the hardness increased accordingly. Therefore, by optimizing the process parameters such as the compressing temperature and compression ratio could generate a targeted density distribution which has the desired hardness.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"45799899","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.488501
Chunmei Yang, Zanbin Zhu, Tongbin Liu, Bo Xue, Wen Qu, Tingting Wang
In this experiment, poplar fibers containing 0%, 2%, 4%, 6%, 8%, 10%, 12%, 14%, 16%, 18%, 20%, 25% and 30% of urea-formaldehyde resin were prepared. A model for the detection of urea-formaldehyde resin content in poplar fibers was established by the hyperspectral near-infrared imaging system combined with relevant algorithms. The spectral images of poplar fibers containing different contents of urea-formaldehyde (UF) resin were measured separately using hyperspectral imager. The results of four preprocessing methods, namely mean centering (MC), multiple scattering correction (MSC), standard normal variables (SNV) and first-order derivative (1-Der) were analyzed, and the optimal preprocessing method was selected as SNV. The band combinations with the highest correlation with the urea-formaldehyde resin content were compared and analyzed with the full-band model to establish the partial least squares regression (PLSR) model. The experimental results show that the hyperspectral imaging system combined with the corresponding algorithm can achieve rapid detection of UF resin content in poplar fibers, and the results of this study provide technical support and theoretical reference for determination of resin content in ultra-thin fiberboard production. The method is an innovative model for the determination of UF resin in wood fibers.
{"title":"DETERMINATION OF UREA-FORMALDEHYDE RESIN CONTENT IN POPLAR FIBER BASED ON HYPERSPECTRAL TECHNIQUES","authors":"Chunmei Yang, Zanbin Zhu, Tongbin Liu, Bo Xue, Wen Qu, Tingting Wang","doi":"10.37763/wr.1336-4561/68.3.488501","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.488501","url":null,"abstract":"In this experiment, poplar fibers containing 0%, 2%, 4%, 6%, 8%, 10%, 12%, 14%, 16%, 18%, 20%, 25% and 30% of urea-formaldehyde resin were prepared. A model for the detection of urea-formaldehyde resin content in poplar fibers was established by the hyperspectral near-infrared imaging system combined with relevant algorithms. The spectral images of poplar fibers containing different contents of urea-formaldehyde (UF) resin were measured separately using hyperspectral imager. The results of four preprocessing methods, namely mean centering (MC), multiple scattering correction (MSC), standard normal variables (SNV) and first-order derivative (1-Der) were analyzed, and the optimal preprocessing method was selected as SNV. The band combinations with the highest correlation with the urea-formaldehyde resin content were compared and analyzed with the full-band model to establish the partial least squares regression (PLSR) model. The experimental results show that the hyperspectral imaging system combined with the corresponding algorithm can achieve rapid detection of UF resin content in poplar fibers, and the results of this study provide technical support and theoretical reference for determination of resin content in ultra-thin fiberboard production. The method is an innovative model for the determination of UF resin in wood fibers.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47983739","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.455464
C. Kang, Kazuharu Hashitsume, E. Jang, H. Kolya
This study aimed to investigate the relationship between surface roughness and anatomical features of wood in 15 different species of boards. Surface roughness was measured parallel and perpendicular to the wood grain using a surface profilometer, and anatomical features such as pore size and distribution were analyzed using microscopic techniques. The results showed that surface roughness perpendicular to the grain direction was consistently higher than that parallel to the grain direction for all wood samples. This difference in roughness was correlated with pore size and density. It shows that the larger pores and lower density lead to higher roughness perpendicular to the grain. The study also found that traditional hand planning methods (push and pull) produced a smooth surface finish, with no statistical differences in roughness.
{"title":"RELATIONSHIP BETWEEN WOOD ANATOMICAL FEATURES AND SURFACE ROUGHNESS CHARACTERISTICS","authors":"C. Kang, Kazuharu Hashitsume, E. Jang, H. Kolya","doi":"10.37763/wr.1336-4561/68.3.455464","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.455464","url":null,"abstract":"This study aimed to investigate the relationship between surface roughness and anatomical features of wood in 15 different species of boards. Surface roughness was measured parallel and perpendicular to the wood grain using a surface profilometer, and anatomical features such as pore size and distribution were analyzed using microscopic techniques. The results showed that surface roughness perpendicular to the grain direction was consistently higher than that parallel to the grain direction for all wood samples. This difference in roughness was correlated with pore size and density. It shows that the larger pores and lower density lead to higher roughness perpendicular to the grain. The study also found that traditional hand planning methods (push and pull) produced a smooth surface finish, with no statistical differences in roughness.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"41712074","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.600618
Š. Boháček, A. Pažitný, Stela Slámová
This article examines the current state of research on energy efficiency in the paper industry, focusing on the key strategies, technologies, and best practices for improving energy efficiency and reducing greenhouse gas emissions. The review covers a range of topics, including energy management systems, process optimisation, cogeneration, waste heat recovery, and renewable energy sources. Overall, the energy efficiency improvements can significantly reduce energy costs and carbon emissions in the paper industry. Still, there is aneed for more comprehensive and integrated approaches that consider the entire value chain of paper production.
{"title":"OPTIMISATION OF ENERGY CONSUMPTION IN PAPER PRODUCTION. REVIEW","authors":"Š. Boháček, A. Pažitný, Stela Slámová","doi":"10.37763/wr.1336-4561/68.3.600618","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.600618","url":null,"abstract":"This article examines the current state of research on energy efficiency in the paper industry, focusing on the key strategies, technologies, and best practices for improving energy efficiency and reducing greenhouse gas emissions. The review covers a range of topics, including energy management systems, process optimisation, cogeneration, waste heat recovery, and renewable energy sources. Overall, the energy efficiency improvements can significantly reduce energy costs and carbon emissions in the paper industry. Still, there is aneed for more comprehensive and integrated approaches that consider the entire value chain of paper production.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46554938","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.477487
D. Kiryakova, Antoniya Ilieva, Neli Simeonova
The behavior of the wood flour-polypropylene composites prepared with various contents of untreated and silane-treated wood flour by immersion in water was studied, as well as the effect of the water absorbed by the samples on their mechanical properties. The highest degree of water absorption was observed for the composites containing 30 – 50 mass% alkali pre-treated wood flour. For the materials with 50 mass% untreated, silane-treated and alkali pre-treated wood flour, the water absorption measured was 8.76%, 7.84% and 13.91%, respectively, after 15 days immersion in water. The value of the thickness swelling calculated for the samples prepared with 50 mass% silane-treated wood flour – polypropylene was the lowest – 1.29%. It was proved that the absorption of water molecules results in change of the tensile profile of the thermoplastic polypropylene composites filled with hygroscopic filler.
{"title":"EFFECT OF WATER ABSORPTION ON THE MECHANICAL PROPERTIES OF SILANE-TREATED WOOD FLOUR POLYPROPYLENE COMPOSITES","authors":"D. Kiryakova, Antoniya Ilieva, Neli Simeonova","doi":"10.37763/wr.1336-4561/68.3.477487","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.477487","url":null,"abstract":"The behavior of the wood flour-polypropylene composites prepared with various contents of untreated and silane-treated wood flour by immersion in water was studied, as well as the effect of the water absorbed by the samples on their mechanical properties. The highest degree of water absorption was observed for the composites containing 30 – 50 mass% alkali pre-treated wood flour. For the materials with 50 mass% untreated, silane-treated and alkali pre-treated wood flour, the water absorption measured was 8.76%, 7.84% and 13.91%, respectively, after 15 days immersion in water. The value of the thickness swelling calculated for the samples prepared with 50 mass% silane-treated wood flour – polypropylene was the lowest – 1.29%. It was proved that the absorption of water molecules results in change of the tensile profile of the thermoplastic polypropylene composites filled with hygroscopic filler.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49334382","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.572581
U. Aras
The aim of this study is to investigate the effect of using vermiculite on the thermal, physical and mechanical properties of cement-bonded particleboards. For this purpose, single-layer cementitious particle boards with a final density of 1200 kg/m3 and a size of 550 x 550 x 10 mm were produced using 2 type vermiculites (crude and expanded) at three different ratios (5%, 10% and 15%). The produced boards were examined in terms of thermal (TGA/DTG), physical (moisture content, density, water absorption and thickness swelling), mechanical (modulus of rupture, modulus of elasticity, internal bond strength and screw withdrawal resistance) properties. According to the TGA results, using both types of vermiculite caused an increase in cement hydration products in the boards and increased the thermal resistance. While the use of vermiculite did not significant effect on the density and moisture content of the boards, it increased the dimensional stability of the boards. The values of modulus of rupture and modulus of elasticity increased when the low amount of vermiculite was added. However, with the use of vermiculite in the boards, there was a decrease in the internal bond strength and screw withdrawal resistance values in general. All boards produced using vermiculite met the values specified in EN standards.
本研究的目的是探讨蛭石对水泥结合刨花板的热性能、物理性能和机械性能的影响。为此，采用2种蛭石(粗的和膨胀的)以3种不同的比例(5%、10%和15%)生产最终密度为1200 kg/m3、尺寸为550 x 550 x 10 mm的单层胶凝刨花板。对所生产的板材进行了热(TGA/DTG)、物理(含水率、密度、吸水性和厚度膨胀)、力学(断裂模量、弹性模量、内部粘结强度和抗拔螺)性能测试。TGA结果表明，两种蛭石的使用均导致板材中水泥水化产物增多，热阻增大。蛭石的使用对板材的密度和含水率没有显著影响，但增加了板材的尺寸稳定性。断裂模量和弹性模量随蛭石添加量的减少而增大。然而，随着在板材中使用蛭石，总体上存在内部粘结强度和螺杆抗拔值的下降。所有使用蛭石生产的板材均符合EN标准规定的值。
{"title":"POSSIBILITY OF USING CRUDE AND EXPANDED VERMICULITE IN CEMENT-BONDED PARTICLEBOARD PRODUCTION","authors":"U. Aras","doi":"10.37763/wr.1336-4561/68.3.572581","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.572581","url":null,"abstract":"The aim of this study is to investigate the effect of using vermiculite on the thermal, physical and mechanical properties of cement-bonded particleboards. For this purpose, single-layer cementitious particle boards with a final density of 1200 kg/m3 and a size of 550 x 550 x 10 mm were produced using 2 type vermiculites (crude and expanded) at three different ratios (5%, 10% and 15%). The produced boards were examined in terms of thermal (TGA/DTG), physical (moisture content, density, water absorption and thickness swelling), mechanical (modulus of rupture, modulus of elasticity, internal bond strength and screw withdrawal resistance) properties. According to the TGA results, using both types of vermiculite caused an increase in cement hydration products in the boards and increased the thermal resistance. While the use of vermiculite did not significant effect on the density and moisture content of the boards, it increased the dimensional stability of the boards. The values of modulus of rupture and modulus of elasticity increased when the low amount of vermiculite was added. However, with the use of vermiculite in the boards, there was a decrease in the internal bond strength and screw withdrawal resistance values in general. All boards produced using vermiculite met the values specified in EN standards.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46573902","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.558571
Tamás Király, Z. Karácsonyi
The purpose of this research is to test Norway spruce specimens with different growth ring orientations weakened by edge-notch until failure. In the experiments the specimens were subjected to 3-point bending, tension and compression tests. In addition, failure mode during loading is investigated using a high-resolution camera. Based on the measurement results the correlation between latewood ratio, ultimate force, ultimate elongation/deflection, calculated moduli, growth ring orientation and diameter of the growth ring at the edge-notch were obtained. Based on the population data of the three tests conducted, only one parameter pair, namely the ratio of latewood to calculated modulus, influences the measurement results to almost the same extent. The other parameter pairs show different values and correlations.
{"title":"FRACTURE TESTING OF EDGE-NOTCHED TIMBER BEAMS WITH DIFFERENT GROWTH RING ORIENTATIONS","authors":"Tamás Király, Z. Karácsonyi","doi":"10.37763/wr.1336-4561/68.3.558571","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.558571","url":null,"abstract":"The purpose of this research is to test Norway spruce specimens with different growth ring orientations weakened by edge-notch until failure. In the experiments the specimens were subjected to 3-point bending, tension and compression tests. In addition, failure mode during loading is investigated using a high-resolution camera. Based on the measurement results the correlation between latewood ratio, ultimate force, ultimate elongation/deflection, calculated moduli, growth ring orientation and diameter of the growth ring at the edge-notch were obtained. Based on the population data of the three tests conducted, only one parameter pair, namely the ratio of latewood to calculated modulus, influences the measurement results to almost the same extent. The other parameter pairs show different values and correlations.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"46899287","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2023-06-28DOI: 10.37763/wr.1336-4561/68.3.547557
P. Rantuch, J. Martinka, Tomáš Štefko, Igor Wachter, Mária Zuzana Bednáriková
Since the methods based on the interaction of a relatively low intensity flame on the lignocellulose sample surface often do not allow measuring the heat release rate (HRR), a procedure using oxygen consumption calorimetry was proposed. The method was applied to OSB samples with dimensions of 320 mm x 140 mm x 25 mm placed in a vertical position. During the measurement, in addition to the HRR, the production of smoke, which was significant after stopping the burner, was also monitored. The average net value of HRR at burner outputs of 3 kW, 4 kW and 5 kW was 2.339 kW and the smoke specific extinction area was in the range of 10.88 m2.kg-1 and 13.19 m2.kg-1.
由于基于木质纤维素样品表面上相对低强度火焰相互作用的方法通常不允许测量热释放率（HRR），因此提出了使用耗氧量热法的程序。该方法应用于放置在垂直位置的尺寸为320 mm x 140 mm x 25 mm的OSB样品。在测量过程中，除了HRR之外，还监测了燃烧器停止后显著的烟雾产生。在3 kW、4 kW和5 kW的燃烧器输出下，HRR的平均净值为2.339 kW，烟比消光面积在10.88 m2.kg-1和13.19 m2.kg--1范围内。
{"title":"CHARACTERIZATION OF THE BURNING OF ORIENTED STRAND BOARDS EXPOSED TO FLAME","authors":"P. Rantuch, J. Martinka, Tomáš Štefko, Igor Wachter, Mária Zuzana Bednáriková","doi":"10.37763/wr.1336-4561/68.3.547557","DOIUrl":"https://doi.org/10.37763/wr.1336-4561/68.3.547557","url":null,"abstract":"Since the methods based on the interaction of a relatively low intensity flame on the lignocellulose sample surface often do not allow measuring the heat release rate (HRR), a procedure using oxygen consumption calorimetry was proposed. The method was applied to OSB samples with dimensions of 320 mm x 140 mm x 25 mm placed in a vertical position. During the measurement, in addition to the HRR, the production of smoke, which was significant after stopping the burner, was also monitored. The average net value of HRR at burner outputs of 3 kW, 4 kW and 5 kW was 2.339 kW and the smoke specific extinction area was in the range of 10.88 m2.kg-1 and 13.19 m2.kg-1.","PeriodicalId":23786,"journal":{"name":"Wood Research","volume":null,"pages":null},"PeriodicalIF":1.3,"publicationDate":"2023-06-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49585855","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"农林科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：