This study focuses on the fabrication and analysis of the mechanical behaviour of unidirectional (UD) glass fibre-reinforced polymer (GFRP) facesheet and polyvinyl chloride (PVC) foam core sandwich structures fabricated by a vacuum-assisted resin infusion method (VARIM). These sandwich structures are commonly used in marine and wind turbine blade applications. To date, relatively little knowledge about the functional behaviour of UD GFRP compared to composites reinforced with bidirectional mats is available for day-to-day applications. The effects of the facesheet orientation, facesheet thickness, and core thickness on the mechanical behaviour of the specimens were examined. The UD fibres were oriented in cross-ply (0/90), angle-ply (+45/−45), and quasi-isotropic orientations. Various mechanical properties such as tensile, flexural, flatwise compression, and edgewise compression tests were examined. Characterization of the tensile properties of the facesheet showed that the cross-ply orientation had a higher strength than the angle-ply and quasi-isotropic orientations. The flexural load-carrying capacity of the cross-ply facesheet orientation was superior to the other orientations. The increase in the core thickness changed the flexural failure mode from face yield and core shear to core indentation. Flatwise compression (FWC) was tested to determine the core characteristics of the sandwich structure, and the peak loads of 4.90, 1.81, and 3.90 kN were obtained for 10-, 15-, and 20 mm core thicknesses, respectively. Edgewise compression (EWC) exhibited stable end crushing for thinner facesheet, whereas thicker facesheet showed core crushing and buckling. When the facesheet thickness was increased from 1.5 mm to 3 mm in the EWC, the buckling load increase ranged from 2.53% to 44.83% for core thicknesses 10-, 15-, and 20 mm, respectively.
{"title":"Mechanical Behaviour of Glass Fibre-Reinforced Polymer/Polyvinyl Chloride Foam Cored Sandwich Structures","authors":"Edwin Cheruiyot Kosgey, Krishnan Kanny, Festus Maina Mwangi","doi":"10.1155/2024/5929170","DOIUrl":"https://doi.org/10.1155/2024/5929170","url":null,"abstract":"This study focuses on the fabrication and analysis of the mechanical behaviour of unidirectional (UD) glass fibre-reinforced polymer (GFRP) facesheet and polyvinyl chloride (PVC) foam core sandwich structures fabricated by a vacuum-assisted resin infusion method (VARIM). These sandwich structures are commonly used in marine and wind turbine blade applications. To date, relatively little knowledge about the functional behaviour of UD GFRP compared to composites reinforced with bidirectional mats is available for day-to-day applications. The effects of the facesheet orientation, facesheet thickness, and core thickness on the mechanical behaviour of the specimens were examined. The UD fibres were oriented in cross-ply (0/90), angle-ply (+45/−45), and quasi-isotropic orientations. Various mechanical properties such as tensile, flexural, flatwise compression, and edgewise compression tests were examined. Characterization of the tensile properties of the facesheet showed that the cross-ply orientation had a higher strength than the angle-ply and quasi-isotropic orientations. The flexural load-carrying capacity of the cross-ply facesheet orientation was superior to the other orientations. The increase in the core thickness changed the flexural failure mode from face yield and core shear to core indentation. Flatwise compression (FWC) was tested to determine the core characteristics of the sandwich structure, and the peak loads of 4.90, 1.81, and 3.90 kN were obtained for 10-, 15-, and 20 mm core thicknesses, respectively. Edgewise compression (EWC) exhibited stable end crushing for thinner facesheet, whereas thicker facesheet showed core crushing and buckling. When the facesheet thickness was increased from 1.5 mm to 3 mm in the EWC, the buckling load increase ranged from 2.53% to 44.83% for core thicknesses 10-, 15-, and 20 mm, respectively.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"67 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-04-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140798099","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
O. J. Aladegboye, O. J. Oyedepo, T. J. Awolola, O. D. Oguntayo, O. Y. Babatunde, O. T. Ilesanmi, P. P. Ikubanni
Waste management and recycling have led to numerous studies on particleboard production. This study attempted to use milled corncob (MCC) and waste ceramic tiles (WCTs) to produce particleboard. The MCC (100−70 wt.%) and WCT (0–30 wt.%) were mixed at different ratios, mixed and compressed at a pressure of 0.25 MPa using urea formaldehyde (UF) resin as adhesive. The physicomechanical and thermal properties of the particleboards produced were investigated. The physical properties (bulk density, water absorption, and thickness swelling) improved with composite particleboard compared to the 100% MCC particleboard. The increase in WCT yielded improved density and lowered the particleboard’s water absorption and thickness swelling. The mechanical tests showed that MOE values were below the recommended standard, which makes them unsuitable for structural use. However, MOR revealed values above the recommended standard. The thermal conductivity of the particleboards was reduced with increased WCT, and the required standard was found to be met. Hence, the particleboards produced are found helpful as thermal wall insulators. Based on the experiments done, sample R7 (70% MCC and 30% WCT) was considered the most preferable since it achieved the most preferable physicomechanical and thermal conductivity performance. The particleboards produced are recommended for wall partitioning and other internal and external purposes.
{"title":"Physicomechanical and Thermal Properties of Particle Board Produced Using Waste Ceramic Materials and Corncob","authors":"O. J. Aladegboye, O. J. Oyedepo, T. J. Awolola, O. D. Oguntayo, O. Y. Babatunde, O. T. Ilesanmi, P. P. Ikubanni","doi":"10.1155/2024/8839814","DOIUrl":"https://doi.org/10.1155/2024/8839814","url":null,"abstract":"Waste management and recycling have led to numerous studies on particleboard production. This study attempted to use milled corncob (MCC) and waste ceramic tiles (WCTs) to produce particleboard. The MCC (100−70 wt.%) and WCT (0–30 wt.%) were mixed at different ratios, mixed and compressed at a pressure of 0.25 MPa using urea formaldehyde (UF) resin as adhesive. The physicomechanical and thermal properties of the particleboards produced were investigated. The physical properties (bulk density, water absorption, and thickness swelling) improved with composite particleboard compared to the 100% MCC particleboard. The increase in WCT yielded improved density and lowered the particleboard’s water absorption and thickness swelling. The mechanical tests showed that MOE values were below the recommended standard, which makes them unsuitable for structural use. However, MOR revealed values above the recommended standard. The thermal conductivity of the particleboards was reduced with increased WCT, and the required standard was found to be met. Hence, the particleboards produced are found helpful as thermal wall insulators. Based on the experiments done, sample R7 (70% MCC and 30% WCT) was considered the most preferable since it achieved the most preferable physicomechanical and thermal conductivity performance. The particleboards produced are recommended for wall partitioning and other internal and external purposes.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"18 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-04-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140613255","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
C. Devanathan, D. Elil Raja, Tushar Sonar, Mikhail Ivanov
The friction stir welding (FSW) method was used to weld B4C reinforced AA 5083 metal matrix composites in this study. By coating titanium nitride (TiN), aluminium chromium nitride (AlCrN), and diamond-like carbon (DLC) to a thickness of 4 microns, three FSW tools with square pin profiles were developed and the friction coefficients of 0.69, 0.32, and 0.2 were maintained. At three levels, the process factors such as tool rotating speed, transverse feed, and axial force were examined. For each tool, 15 samples were made using the central composite design. The influence of the friction coefficient on ultimate tensile strength, microstructural features, and tool condition was studied, and the flower pollination algorithm (FPA) technique was used to find the best process parameters for obtaining maximum ultimate tensile strength of FSW joints. The improved tensile strength of FSW joints was verified using a validation test. The coating has a considerable influence on the ultimate tensile strength, microstructure, and tool condition, according to the results of the tool’s friction coefficient. The results on the prediction of strength using the fuzzy clustering technique showed that the technique is effective in predicting the tensile strength values, with the root mean square error (RSME) of TiN, AlCrN, and DLC being 0.0027, 0.0016, and 0.0015, respectively, and the low RSME indicating that the prediction based on the fuzzy subtractive clustering technique is perfect and effective.
{"title":"Effect of Friction Coefficient in Friction Stir Welding of B4C Reinforced AA5083 Metal Matrix Composites and Use of Fuzzy Clustering Technique for Weld Strength Prediction","authors":"C. Devanathan, D. Elil Raja, Tushar Sonar, Mikhail Ivanov","doi":"10.1155/2024/9880686","DOIUrl":"https://doi.org/10.1155/2024/9880686","url":null,"abstract":"The friction stir welding (FSW) method was used to weld B4C reinforced AA 5083 metal matrix composites in this study. By coating titanium nitride (TiN), aluminium chromium nitride (AlCrN), and diamond-like carbon (DLC) to a thickness of 4 microns, three FSW tools with square pin profiles were developed and the friction coefficients of 0.69, 0.32, and 0.2 were maintained. At three levels, the process factors such as tool rotating speed, transverse feed, and axial force were examined. For each tool, 15 samples were made using the central composite design. The influence of the friction coefficient on ultimate tensile strength, microstructural features, and tool condition was studied, and the flower pollination algorithm (FPA) technique was used to find the best process parameters for obtaining maximum ultimate tensile strength of FSW joints. The improved tensile strength of FSW joints was verified using a validation test. The coating has a considerable influence on the ultimate tensile strength, microstructure, and tool condition, according to the results of the tool’s friction coefficient. The results on the prediction of strength using the fuzzy clustering technique showed that the technique is effective in predicting the tensile strength values, with the root mean square error (RSME) of TiN, AlCrN, and DLC being 0.0027, 0.0016, and 0.0015, respectively, and the low RSME indicating that the prediction based on the fuzzy subtractive clustering technique is perfect and effective.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"62 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-04-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140590919","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Sumit Kumar, Yan-Shu Huang, Zoltan Nagy, Gintaras V. Reklaitis, Marcial Gonzalez, Paul Mort
The pharmaceutical industry is looking for new and innovative ways of manufacturing to improve product quality and reduce process complexity. In manufacturing oral solid dosage products, blending is a crucial step in ensuring the homogeneity of active pharmaceutical ingredients (APIs) in the final product. Currently, batch and continuous blending are the two commonly used modes for blending in the industry. However, these methods have limitations in terms of blending time, manual intervention, and flexibility in handling multiple ingredients. To address these limitations, this study aims to explore the feasibility and benefits of using a semicontinuous blending mode in the pharmaceutical industry. A case study is conducted using a binary blend of microcrystalline cellulose and acetaminophen to compare the performance of the semicontinuous mode of blending with the batch and continuous blending modes. The results show that the semicontinuous blending setup can produce blends with good blend uniformity and homogeneity and that the output can be used for both batch and continuous downstream operations. The effect of variation in the three most important process parameters, impeller rotation per minute, blending time, and fill level on the blend uniformity, is also investigated. The semicontinuous blending mode had a higher line rate of 12.5 kg/hour than a similarly sized batch blender at 3.6 kg/hour and less than that of a continuous blender. The benefits of the new blending mode include reduced blending time, minimal manual intervention, flexibility in blending multiple ingredients, easier scale-up, and a smaller footprint. Overall, this study highlights the relative advantages of using this new semicontinuous blending mode in pharmaceutical manufacturing and its potential as a good alternative to the existing blending modes. The semicontinuous mode is well placed between the batch blending and continuous blending mode, with many benefits over the former mode and performance comparable to the latter continuous mode.
{"title":"Semicontinuous Blending of Pharmaceutical Ingredients and the Impact of Process Parameters on the Blending Performance of an Integrated Feeder Blender Operating Semicontinuously","authors":"Sumit Kumar, Yan-Shu Huang, Zoltan Nagy, Gintaras V. Reklaitis, Marcial Gonzalez, Paul Mort","doi":"10.1155/2024/8816672","DOIUrl":"https://doi.org/10.1155/2024/8816672","url":null,"abstract":"The pharmaceutical industry is looking for new and innovative ways of manufacturing to improve product quality and reduce process complexity. In manufacturing oral solid dosage products, blending is a crucial step in ensuring the homogeneity of active pharmaceutical ingredients (APIs) in the final product. Currently, batch and continuous blending are the two commonly used modes for blending in the industry. However, these methods have limitations in terms of blending time, manual intervention, and flexibility in handling multiple ingredients. To address these limitations, this study aims to explore the feasibility and benefits of using a semicontinuous blending mode in the pharmaceutical industry. A case study is conducted using a binary blend of microcrystalline cellulose and acetaminophen to compare the performance of the semicontinuous mode of blending with the batch and continuous blending modes. The results show that the semicontinuous blending setup can produce blends with good blend uniformity and homogeneity and that the output can be used for both batch and continuous downstream operations. The effect of variation in the three most important process parameters, impeller rotation per minute, blending time, and fill level on the blend uniformity, is also investigated. The semicontinuous blending mode had a higher line rate of 12.5 kg/hour than a similarly sized batch blender at 3.6 kg/hour and less than that of a continuous blender. The benefits of the new blending mode include reduced blending time, minimal manual intervention, flexibility in blending multiple ingredients, easier scale-up, and a smaller footprint. Overall, this study highlights the relative advantages of using this new semicontinuous blending mode in pharmaceutical manufacturing and its potential as a good alternative to the existing blending modes. The semicontinuous mode is well placed between the batch blending and continuous blending mode, with many benefits over the former mode and performance comparable to the latter continuous mode.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"15 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-03-29","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140324052","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Shamima Mehrin, Nilufer Yesmin Tanisa, Rabiul Awal, Md. Kamrul Alam Khan, Abdus Shaqur, Shamim Ahmed, Shahidul Islam, Asad Mia
The present study investigates an environmentally conscious method for synthesizing silver nanoparticles (AgNPs) by employing extracts from pomegranate peel (PgP) and pineapple peel (PnP). This green synthesis approach offers a sustainable alternative to traditional chemical methods, thereby reducing the ecological footprint associated with nanoparticle production. The PgP and PnP extracts serve as both reducing and capping agents during the synthesis process, enhancing the biocompatibility of the resultant AgNPs. Various characterization techniques, including UV-Vis spectroscopy, Raman analysis, X-ray diffraction (XRD), dynamic light scattering (DLS), Fourier transform infrared (FTIR), and transmission electron microscopy (TEM), were utilized to analyze the synthesized AgNPs. UV-Vis spectroscopy confirmed the formation of AgNPs through characteristic surface plasmon resonance peaks, while FTIR examined the interaction between biomaterial components and the oxidation and coating of silver nanoparticles. Raman analysis elucidated the functional groups responsible for reducing and stabilizing AgNPs, while XRD provided insights into their crystalline structure. TEM images revealed the size and morphology of the nanoparticles, while DLS characterized their average size and morphology. In addition, the synthesized AgNPs were utilized in a bioelectrochemical cell to leverage their unique properties for enhanced electrochemical performance, showcasing their potential application in energy storage and conversion systems. Overall, this study demonstrates the feasibility of utilizing agricultural waste products such as PgP and PnP for sustainable AgNP synthesis, offering promising prospects for environmentally friendly nanotechnology advancement.
{"title":"Efficient Bioelectrochemical Cell Generation and Green Synthesis of Silver Nanoparticles Using Pomegranate and Pineapple Peel Extracts: A Comprehensive Characterization Study","authors":"Shamima Mehrin, Nilufer Yesmin Tanisa, Rabiul Awal, Md. Kamrul Alam Khan, Abdus Shaqur, Shamim Ahmed, Shahidul Islam, Asad Mia","doi":"10.1155/2024/6681559","DOIUrl":"https://doi.org/10.1155/2024/6681559","url":null,"abstract":"The present study investigates an environmentally conscious method for synthesizing silver nanoparticles (AgNPs) by employing extracts from pomegranate peel (PgP) and pineapple peel (PnP). This green synthesis approach offers a sustainable alternative to traditional chemical methods, thereby reducing the ecological footprint associated with nanoparticle production. The PgP and PnP extracts serve as both reducing and capping agents during the synthesis process, enhancing the biocompatibility of the resultant AgNPs. Various characterization techniques, including UV-Vis spectroscopy, Raman analysis, X-ray diffraction (XRD), dynamic light scattering (DLS), Fourier transform infrared (FTIR), and transmission electron microscopy (TEM), were utilized to analyze the synthesized AgNPs. UV-Vis spectroscopy confirmed the formation of AgNPs through characteristic surface plasmon resonance peaks, while FTIR examined the interaction between biomaterial components and the oxidation and coating of silver nanoparticles. Raman analysis elucidated the functional groups responsible for reducing and stabilizing AgNPs, while XRD provided insights into their crystalline structure. TEM images revealed the size and morphology of the nanoparticles, while DLS characterized their average size and morphology. In addition, the synthesized AgNPs were utilized in a bioelectrochemical cell to leverage their unique properties for enhanced electrochemical performance, showcasing their potential application in energy storage and conversion systems. Overall, this study demonstrates the feasibility of utilizing agricultural waste products such as PgP and PnP for sustainable AgNP synthesis, offering promising prospects for environmentally friendly nanotechnology advancement.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"46 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-03-28","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140313411","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Mohammad Tarikuzzaman, Viral Sagar, Mark James Wong, Joan G. Lynam
Phase behavior, density, viscosity, conductivity, pH, and surface tension were measured, and FTIR was performed for a series of mixtures of sugar (glucose, fructose, xylose, and sucrose), water, and choline chloride (ChCl) at specific molar ratios. These mixtures, called sugar-based natural deep eutectic solvents (NADESs), were investigated as a function of temperature. Contact angle measurements indicated that NADES exhibited slightly lower wettability but higher surface tension than water. Temperature was found to greatly impact density, viscosity, and conductivity. The optimum water molar ratio for lower viscosity was found at ratios higher than those reported in the literature, indicating that the NADES investigated may have industrial process applications.
{"title":"Temperature Effects on Physiochemical Characteristics of Sugar-Based Natural Deep Eutectic Solvents","authors":"Mohammad Tarikuzzaman, Viral Sagar, Mark James Wong, Joan G. Lynam","doi":"10.1155/2024/6641317","DOIUrl":"https://doi.org/10.1155/2024/6641317","url":null,"abstract":"Phase behavior, density, viscosity, conductivity, pH, and surface tension were measured, and FTIR was performed for a series of mixtures of sugar (glucose, fructose, xylose, and sucrose), water, and choline chloride (ChCl) at specific molar ratios. These mixtures, called sugar-based natural deep eutectic solvents (NADESs), were investigated as a function of temperature. Contact angle measurements indicated that NADES exhibited slightly lower wettability but higher surface tension than water. Temperature was found to greatly impact density, viscosity, and conductivity. The optimum water molar ratio for lower viscosity was found at ratios higher than those reported in the literature, indicating that the NADES investigated may have industrial process applications.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"27 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-03-22","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140199644","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
L. Karthick, Mruthunjaya M., Srinivas. S., Prasanna Venkatesh R., Naveen Kumar Gurajala, Meghavath Mothilal, Hari Banda
In this research, the main aim is to focus the enhancement of aluminium-based metal matrix composites for improving the attributes of light weight metals, aerospace structures and other tailor blank material properties. By this way, the friction stir processing (FSP) was the suited alternate technique to enhancing the mechanical attributes and superior microstructural amendment in the processed MMCs. Therefore, this study investigates the dispersion of ceramic-based strengthening particles of chromium oxide (Cr2O3) in the aluminium base matrix of A356 alloy. During the processing, the different tool pin sizes having the conical threaded tool pin profiles. Similarly, the tool spinning speed and tool travel speed also varied while in FSP. Before the processing, the A356 alloy was prepared by the grooved surfaces for packing the chromium oxide particles to compose the aluminium metal matrix composites. The tensile strength and hardness was employed to carry out from the friction stir processed A356 alloy with influencing of Cr2O3. The maximum occurred tensile processing parameters are 1500 rpm of spinning speed, 6 mm of tool pin sizes and 90 mm/min of tool travel speed. Similarly, the maximum obtained hardness processing parameter are 2000 rpm of spinning speed, 5 mm of tool pin sizes and 90 mm/min of tool travel speed. A scanning electron microscope was utilized to investigate the dispersed Cr2O3 in the A356 alloy for confirming the refinement grains in the nugget zones of FSPed A356 alloy. The increased grain boundary by the influence of different tool pin sizes was the major reason to produces the better mechanical properties in the processed A356/Cr2O3.
{"title":"Influence of Tool Pin Profiles on Aluminium Alloy A356 and Ceramic-Based Nanocomposites for Light Weight Structures by Friction Stir Processing","authors":"L. Karthick, Mruthunjaya M., Srinivas. S., Prasanna Venkatesh R., Naveen Kumar Gurajala, Meghavath Mothilal, Hari Banda","doi":"10.1155/2024/2494900","DOIUrl":"https://doi.org/10.1155/2024/2494900","url":null,"abstract":"In this research, the main aim is to focus the enhancement of aluminium-based metal matrix composites for improving the attributes of light weight metals, aerospace structures and other tailor blank material properties. By this way, the friction stir processing (FSP) was the suited alternate technique to enhancing the mechanical attributes and superior microstructural amendment in the processed MMCs. Therefore, this study investigates the dispersion of ceramic-based strengthening particles of chromium oxide (Cr<sub>2</sub>O<sub>3</sub>) in the aluminium base matrix of A356 alloy. During the processing, the different tool pin sizes having the conical threaded tool pin profiles. Similarly, the tool spinning speed and tool travel speed also varied while in FSP. Before the processing, the A356 alloy was prepared by the grooved surfaces for packing the chromium oxide particles to compose the aluminium metal matrix composites. The tensile strength and hardness was employed to carry out from the friction stir processed A356 alloy with influencing of Cr<sub>2</sub>O<sub>3</sub>. The maximum occurred tensile processing parameters are 1500 rpm of spinning speed, 6 mm of tool pin sizes and 90 mm/min of tool travel speed. Similarly, the maximum obtained hardness processing parameter are 2000 rpm of spinning speed, 5 mm of tool pin sizes and 90 mm/min of tool travel speed. A scanning electron microscope was utilized to investigate the dispersed Cr<sub>2</sub>O<sub>3</sub> in the A356 alloy for confirming the refinement grains in the nugget zones of FSPed A356 alloy. The increased grain boundary by the influence of different tool pin sizes was the major reason to produces the better mechanical properties in the processed A356/Cr<sub>2</sub>O<sub>3</sub>.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"19 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-03-18","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140155500","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Swelling of anhydrite rock causes serious damage to the tunnel and generates high additional costs in the process of tunnel construction and operation and has gradually become one of the main factors that threaten the safety of the tunnel. It is extremely difficult to predict swelling pressures and deformations accurately based on conventional swelling constitutive models. Thus, a new practical swelling constitutive model of anhydrite for tunnel engineering has been developed. First, swelling tests of natural anhydrite samples focusing on the time effect have been designed and conducted, whose test results show that swelling strain-time can be described by the S-curve model and that swelling stress-strain can be described by the quadratic model. Second, a swelling constitutive model with considering the time effect has been developed to reproduce the swelling behavior of anhydrite observed in swelling tests. This model can track the evolution of swelling activity in tunneling, which has practical significance for process simulation and process control of swelling disaster. Then, this model has been implemented within ANSYS for numerical simulation of the Lirang tunnel. Based on simulation results, useful measures have been proposed. Satisfactory results have been achieved according to the feedback from the site.
无水岩的膨胀会对隧道造成严重破坏，并在隧道建设和运营过程中产生高昂的额外成本，已逐渐成为威胁隧道安全的主要因素之一。根据传统的膨胀构造模型，要准确预测膨胀压力和变形是非常困难的。因此，我们开发了一种用于隧道工程的新型实用无水石膏膨胀构造模型。首先，设计并进行了以时间效应为重点的天然无水石膏样品膨胀试验，试验结果表明，膨胀应变-时间可以用 S 曲线模型描述，膨胀应力-应变可以用二次模型描述。其次，建立了考虑时间效应的膨胀构成模型，以再现膨胀试验中观察到的无水石膏的膨胀行为。该模型可跟踪隧道中膨胀活动的演变，对膨胀灾害的过程模拟和过程控制具有实际意义。随后，该模型在 ANSYS 中实现，用于里郎隧道的数值模拟。根据模拟结果，提出了一些有用的措施。根据现场反馈，取得了令人满意的结果。
{"title":"A Practical Swelling Constitutive Model of Anhydrite and Its Application on Tunnel Engineering","authors":"Jianxun Wu, Fei Lin, Xiaohong Zhou, Zhigang Zhang, Jinyang Fan, Zhenkun Hou","doi":"10.1155/2024/7961951","DOIUrl":"https://doi.org/10.1155/2024/7961951","url":null,"abstract":"Swelling of anhydrite rock causes serious damage to the tunnel and generates high additional costs in the process of tunnel construction and operation and has gradually become one of the main factors that threaten the safety of the tunnel. It is extremely difficult to predict swelling pressures and deformations accurately based on conventional swelling constitutive models. Thus, a new practical swelling constitutive model of anhydrite for tunnel engineering has been developed. First, swelling tests of natural anhydrite samples focusing on the time effect have been designed and conducted, whose test results show that swelling strain-time can be described by the S-curve model and that swelling stress-strain can be described by the quadratic model. Second, a swelling constitutive model with considering the time effect has been developed to reproduce the swelling behavior of anhydrite observed in swelling tests. This model can track the evolution of swelling activity in tunneling, which has practical significance for process simulation and process control of swelling disaster. Then, this model has been implemented within ANSYS for numerical simulation of the Lirang tunnel. Based on simulation results, useful measures have been proposed. Satisfactory results have been achieved according to the feedback from the site.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"25 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-03-14","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"140128766","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Zinc oxide nanoparticles (ZnO-NPs) are used in various fields such as industrial, environmental remediation, catalytic, and antibacterial applications. However, their ability to absorb visible light is limited due to their high-energy bandgap and fast electron-hole recombination, which restricts their use. To enhance the efficiency of ZnO-NPs in medical and other applications, surface functionality can be modified through doping. Here, we investigated the effects of S and N doping on the energy bandgap of ZnO-NP and their antimicrobial and antioxidant activities. The results showed that the optical bandgap energy of pure ZnO-NPs was 2.98 eV while that of 6% N-ZnO, 4% S-ZnO, and S4-N6-ZnO was 2.78, 2.69, and 2.63 eV, respectively. The energy bandgap reduction is attributed to the changes in the electronic level of zinc oxide as the result of doping. The crystal size of pure ZnO-NPs, 6% N-ZnO, 4% S-ZnO, and S4-N6-ZnO was 29.06, 27.05, 29.02, and 25.06 nm, respectively, as calculated from XRD data using FWHM. Following the bandgap and particle size reduction, the antimicrobial activities of the dual-doped ZnO-NPs surpassed that of the pure ZnO-NPs. Moreover, dual doping improved the antioxidant activity of ZnO-NPs from 52.45% to 88.89% for the optimized concentration. Therefore, incorporating S and N as dual dopants can enhance the functionality and efficiency of ZnO-NPs in various fields.
{"title":"Effect of Codoping Zinc Oxide Nanoparticles with Sulfur and Nitrogen on Its Energy Bandgap, Antioxidant Properties, and Antibacterial Activity","authors":"Diriba Yadesa, Jabessa Nagasa Guyasa, Tamene Tadesse Beyene","doi":"10.1155/2024/4275035","DOIUrl":"https://doi.org/10.1155/2024/4275035","url":null,"abstract":"Zinc oxide nanoparticles (ZnO-NPs) are used in various fields such as industrial, environmental remediation, catalytic, and antibacterial applications. However, their ability to absorb visible light is limited due to their high-energy bandgap and fast electron-hole recombination, which restricts their use. To enhance the efficiency of ZnO-NPs in medical and other applications, surface functionality can be modified through doping. Here, we investigated the effects of S and N doping on the energy bandgap of ZnO-NP and their antimicrobial and antioxidant activities. The results showed that the optical bandgap energy of pure ZnO-NPs was 2.98 eV while that of 6% N-ZnO, 4% S-ZnO, and S4-N6-ZnO was 2.78, 2.69, and 2.63 eV, respectively. The energy bandgap reduction is attributed to the changes in the electronic level of zinc oxide as the result of doping. The crystal size of pure ZnO-NPs, 6% N-ZnO, 4% S-ZnO, and S4-N6-ZnO was 29.06, 27.05, 29.02, and 25.06 nm, respectively, as calculated from XRD data using FWHM. Following the bandgap and particle size reduction, the antimicrobial activities of the dual-doped ZnO-NPs surpassed that of the pure ZnO-NPs. Moreover, dual doping improved the antioxidant activity of ZnO-NPs from 52.45% to 88.89% for the optimized concentration. Therefore, incorporating S and N as dual dopants can enhance the functionality and efficiency of ZnO-NPs in various fields.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"28 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-02-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139977618","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Jinggan Shao, Zhanshu He, Genshang Wu, Zhi Zhang, Chao Li
In order to achieve the change rule of the induced residual stress (RS) field after multipass ultrasonic surface rolling (USR), a mathematical model of the induced residual stress (RS) field after multipass ultrasonic surface rolling is first established. Then, the coupling mechanisms of the RS field after dual-pass USR and multipass USR are analyzed, respectively. Subsequently, a finite element (FE) model is established, and the influence of the interval between two adjacent rolling paths is investigated. Finally, both the mathematical model and the FE model are experimentally verified. The results show that both the mathematical model and the FE model can predict the RS field after multipass USR. Two adjacent RS fields will couple with each other in their overlapping regions. For a relatively small interval , the RS field after multipass USR can be fully coupled, so as to form a uniform compressive RS layer. In this study, when = 0.05 mm, the values of the surface compressive RS, the maximum compressive RS, the depth of the maximum compressive RS, and the depth of the compressive RS layer reach 426.71 MPa, 676.54 MPa, 0.05 mm, and 0.54 mm, respectively.
{"title":"Mathematical Modeling and Finite Element Analysis of Residual Stress (RS) Field after Multipass Ultrasonic Surface Rolling","authors":"Jinggan Shao, Zhanshu He, Genshang Wu, Zhi Zhang, Chao Li","doi":"10.1155/2024/4083427","DOIUrl":"https://doi.org/10.1155/2024/4083427","url":null,"abstract":"In order to achieve the change rule of the induced residual stress (RS) field after multipass ultrasonic surface rolling (USR), a mathematical model of the induced residual stress (RS) field after multipass ultrasonic surface rolling is first established. Then, the coupling mechanisms of the RS field after dual-pass USR and multipass USR are analyzed, respectively. Subsequently, a finite element (FE) model is established, and the influence of the interval between two adjacent rolling paths <svg height=\"11.927pt\" style=\"vertical-align:-3.291101pt\" version=\"1.1\" viewbox=\"-0.0498162 -8.6359 13.289 11.927\" width=\"13.289pt\" xmlns=\"http://www.w3.org/2000/svg\" xmlns:xlink=\"http://www.w3.org/1999/xlink\"><g transform=\"matrix(.013,0,0,-0.013,0,0)\"></path></g><g transform=\"matrix(.0091,0,0,-0.0091,8.294,3.132)\"></path></g></svg> is investigated. Finally, both the mathematical model and the FE model are experimentally verified. The results show that both the mathematical model and the FE model can predict the RS field after multipass USR. Two adjacent RS fields will couple with each other in their overlapping regions. For a relatively small interval <span><svg height=\"11.927pt\" style=\"vertical-align:-3.291101pt\" version=\"1.1\" viewbox=\"-0.0498162 -8.6359 13.289 11.927\" width=\"13.289pt\" xmlns=\"http://www.w3.org/2000/svg\" xmlns:xlink=\"http://www.w3.org/1999/xlink\"><g transform=\"matrix(.013,0,0,-0.013,0,0)\"><use xlink:href=\"#g113-77\"></use></g><g transform=\"matrix(.0091,0,0,-0.0091,8.294,3.132)\"><use xlink:href=\"#g50-84\"></use></g></svg>,</span> the RS field after multipass USR can be fully coupled, so as to form a uniform compressive RS layer. In this study, when <svg height=\"11.927pt\" style=\"vertical-align:-3.291101pt\" version=\"1.1\" viewbox=\"-0.0498162 -8.6359 13.289 11.927\" width=\"13.289pt\" xmlns=\"http://www.w3.org/2000/svg\" xmlns:xlink=\"http://www.w3.org/1999/xlink\"><g transform=\"matrix(.013,0,0,-0.013,0,0)\"><use xlink:href=\"#g113-77\"></use></g><g transform=\"matrix(.0091,0,0,-0.0091,8.294,3.132)\"><use xlink:href=\"#g50-84\"></use></g></svg> = 0.05 mm, the values of the surface compressive RS, the maximum compressive RS, the depth of the maximum compressive RS, and the depth of the compressive RS layer reach 426.71 MPa, 676.54 MPa, 0.05 mm, and 0.54 mm, respectively.","PeriodicalId":7345,"journal":{"name":"Advances in Materials Science and Engineering","volume":"15 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2024-02-16","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"139761241","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":4,"RegionCategory":"材料科学","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：