Contemporary urban discourse is paying increasing attention to the issue of urban resilience, due to the stresses, disasters and disturbances (natural and human) that the cities of the world are experiencing and facing, which confirms the need to be familiar with the concept of urban resilience, its dimensions, practices, and characteristics at different levels; In order to reach the aspects of developing the urban energy sector in them, and in a way that supports the preparedness of cities to face potential expected and unexpected disturbances in the future, as cities are usually formed from many main and sub-systems that are dynamically intertwined with each other, such as: the social and economic system, infrastructure systems, land use, and media Various transports, which have a high level of direct interactions with the natural environment; ; It is therefore necessary to understand how the city deals with the odds of threats and challenges in an integrated manner; To overcome its weaknesses and enhance its resilience of use, which aims to make cities more secure, resilient and sustainable in the future, as well as that requires rethinking the field of expanding the use of renewable energies and the general urban landscape. To become a search problem “Failure to exploit the potential of natural energies on the possibility of exploiting renewable natural energies with their components (active and passive) in the production of resilience urban formations in cities.” The aim of the research is to try to "extract an integrated theoretical framework on the characteristics of urban energy resilience from international and Arab experiences, and to diagnose its most important planning and design pillars and indicators, which can be adopted to evaluate the reality of urban energy resilience in local cities." The research hypothesized that “the exploitation of energy systems produced from renewable natural resources, for the purposes of environmental treatments for resilient cities, especially in the buildings of housing projects and their urban surroundings, reduces the consumption of fossil energies for the city, frees its sites from linking to depleted energy transmission networks, and reduces potential environmental pollution problems, which contributes to in the production of flexible energy systems and helps in the generation of flexible cities." The descriptive analysis method was adopted.
{"title":"Diagnosing the Integration of Resilient City Pillars and Indicators with Urban Energy Systems","authors":"Aisha Saleh, Khalid Abdul Wahab Al-Mudares","doi":"10.29194/njes.2502a001","DOIUrl":"https://doi.org/10.29194/njes.2502a001","url":null,"abstract":"Contemporary urban discourse is paying increasing attention to the issue of urban resilience, due to the stresses, disasters and disturbances (natural and human) that the cities of the world are experiencing and facing, which confirms the need to be familiar with the concept of urban resilience, its dimensions, practices, and characteristics at different levels; In order to reach the aspects of developing the urban energy sector in them, and in a way that supports the preparedness of cities to face potential expected and unexpected disturbances in the future, as cities are usually formed from many main and sub-systems that are dynamically intertwined with each other, such as: the social and economic system, infrastructure systems, land use, and media Various transports, which have a high level of direct interactions with the natural environment; ; It is therefore necessary to understand how the city deals with the odds of threats and challenges in an integrated manner; To overcome its weaknesses and enhance its resilience of use, which aims to make cities more secure, resilient and sustainable in the future, as well as that requires rethinking the field of expanding the use of renewable energies and the general urban landscape. To become a search problem “Failure to exploit the potential of natural energies on the possibility of exploiting renewable natural energies with their components (active and passive) in the production of resilience urban formations in cities.” The aim of the research is to try to \"extract an integrated theoretical framework on the characteristics of urban energy resilience from international and Arab experiences, and to diagnose its most important planning and design pillars and indicators, which can be adopted to evaluate the reality of urban energy resilience in local cities.\"\u0000The research hypothesized that “the exploitation of energy systems produced from renewable natural resources, for the purposes of environmental treatments for resilient cities, especially in the buildings of housing projects and their urban surroundings, reduces the consumption of fossil energies for the city, frees its sites from linking to depleted energy transmission networks, and reduces potential environmental pollution problems, which contributes to in the production of flexible energy systems and helps in the generation of flexible cities.\" The descriptive analysis method was adopted.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"18 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-07-19","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"81941087","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
In this work, the vibrations in the rotor-bearing system are studied experimentally and theoretically using ANSYS Workbench 2020 R1 software to compute the natural frequencies and mode shapes. In the experimental part, the LABVIEW software was used to examine the signal of the frequency domain values obtained from the accelerometer sensors, based on Fast Fourier Transform (FFT) technology and dynamic response spectrum. in the theoretical part, the natural frequencies are determined based on the finite element method for analyzing the system and knowing its behavior and vibration response level. The results showed that the level of vibration becomes higher at high rotational speeds, and it becomes large when the distances between the bearings are large, according to the bearing position and type used in the system. in this work can be concluded, the system is usually affected by the dynamic response around it and is difficult to separate from it, and the vibrations in the system can be controlled by adding an external damping source, which gives the system more stable. A system operating at high speeds can give a large vibration and an unbalanced response.
{"title":"Vibration Characteristics of the Bearing Rotor Shaft","authors":"Karrar Baher, Q. Atiyah, I. Abdulsahib","doi":"10.29194/njes.25010049","DOIUrl":"https://doi.org/10.29194/njes.25010049","url":null,"abstract":"In this work, the vibrations in the rotor-bearing system are studied experimentally and theoretically using ANSYS Workbench 2020 R1 software to compute the natural frequencies and mode shapes. In the experimental part, the LABVIEW software was used to examine the signal of the frequency domain values obtained from the accelerometer sensors, based on Fast Fourier Transform (FFT) technology and dynamic response spectrum. in the theoretical part, the natural frequencies are determined based on the finite element method for analyzing the system and knowing its behavior and vibration response level. The results showed that the level of vibration becomes higher at high rotational speeds, and it becomes large when the distances between the bearings are large, according to the bearing position and type used in the system. in this work can be concluded, the system is usually affected by the dynamic response around it and is difficult to separate from it, and the vibrations in the system can be controlled by adding an external damping source, which gives the system more stable. A system operating at high speeds can give a large vibration and an unbalanced response.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"16 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"78640911","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The hydrodynamics of stirred tanks and bubble breakup are crucial in gas-liquid flows, yet this system has not been well characterized for different operating conditions. In this work, the numerical method was used to investigate the hydrodynamics of six- flat blades impeller (Rushton turbine) and the results were employed to understand the bubble breakup behavior in the stirred tank. Simulation results of predicted flow pattern, power number, and the distribution of turbulence energy generated were performed with COMSOL Multiphysics. Numerical results showed good agreement with the experimental literature. The effect of rotational speed on bubble breakup behavior, such as breakage probability, the average number of daughter bubbles, and the breakage time was investigated using the high-speed imaging method. The main finding is that the breakage process occurs in the high energy area of high turbulence intensity, which is located within a distance equal to the blade width of a radius of (15-35 mm). The breakage probability (Bp) was found to be increased by 12.61 percent for a mother bubble of 4 mm at 340 rpm, with an average fragmentation of up to 22 fragments. Furthermore, the bubble breakage time was found to decrease with increasing impeller rotational speed, with an average value of 19.8 ms.
{"title":"Hydrodynamics of Stirred Tank and Bubble Breakup Behavior Induced by Rushton Turbine","authors":"Anas Malik Mhawesh, Basim O. Hasan, H. Znad","doi":"10.29194/njes.25010035","DOIUrl":"https://doi.org/10.29194/njes.25010035","url":null,"abstract":"The hydrodynamics of stirred tanks and bubble breakup are crucial in gas-liquid flows, yet this system has not been well characterized for different operating conditions. In this work, the numerical method was used to investigate the hydrodynamics of six- flat blades impeller (Rushton turbine) and the results were employed to understand the bubble breakup behavior in the stirred tank. Simulation results of predicted flow pattern, power number, and the distribution of turbulence energy generated were performed with COMSOL Multiphysics. Numerical results showed good agreement with the experimental literature. The effect of rotational speed on bubble breakup behavior, such as breakage probability, the average number of daughter bubbles, and the breakage time was investigated using the high-speed imaging method. The main finding is that the breakage process occurs in the high energy area of high turbulence intensity, which is located within a distance equal to the blade width of a radius of (15-35 mm). The breakage probability (Bp) was found to be increased by 12.61 percent for a mother bubble of 4 mm at 340 rpm, with an average fragmentation of up to 22 fragments. Furthermore, the bubble breakage time was found to decrease with increasing impeller rotational speed, with an average value of 19.8 ms.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"30 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"91157982","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The interest in the Eye-tracking technology field dramatically grew up in the last two decades for different purposes and applications like keeping the focus of where the person is looking, how his pupils and irises are reacting for a variety of actions, etc. The resulted data can deliver an extraordinary amount of information about the user when it's interlocked through advanced data analysis systems, it may show information concerned with the user’s age, gender, biometric identity, interests, etc. This paper is concerned about eye motion tracking as an unadulterated tool for different applications in any field required. The improvements in this area of artificial intelligence (AI), machine learning (ML), and deep learning (DL) with eye-tracking techniques allow large opportunities to develop algorithms and applications. In this paper number of models were proposed based on Convolutional neural network (CNN) have been designed, and then the most powerful and accurate model was chosen. The dataset used for the training process (for 16 screen points) consists of 2800 training images and 800 test images (with an average of 175 training images and 50 test images for each spot on the screen of the 16 spots), and it can be collected by the user of any application based on this model. The highest accuracy achieved by the best model was (91.25%) and the minimum loss was (0.23%). The best model consists of (11) layers (4 convolutions, 4 Max pooling, and 3 Dense). Python 3.7 was used to implement the algorithms, KERAS framework for the deep learning algorithms, Visual studio code as an Integrated Development Environment (IDE), and Anaconda navigator for downloading the different libraries. The model was trained with data that can be gathered using cameras of laptops or PCs and without the necessity of special and expensive equipment, also It can be trained for any single eye, depending on application requirements.
{"title":"Improvement of Eye Tracking Based on Deep Learning Model for General Purpose Applications","authors":"Ahmed Aamer Almindelawy, Mohammed H. Ali","doi":"10.29194/njes.25010012","DOIUrl":"https://doi.org/10.29194/njes.25010012","url":null,"abstract":"The interest in the Eye-tracking technology field dramatically grew up in the last two decades for different purposes and applications like keeping the focus of where the person is looking, how his pupils and irises are reacting for a variety of actions, etc. The resulted data can deliver an extraordinary amount of information about the user when it's interlocked through advanced data analysis systems, it may show information concerned with the user’s age, gender, biometric identity, interests, etc. This paper is concerned about eye motion tracking as an unadulterated tool for different applications in any field required. The improvements in this area of artificial intelligence (AI), machine learning (ML), and deep learning (DL) with eye-tracking techniques allow large opportunities to develop algorithms and applications. In this paper number of models were proposed based on Convolutional neural network (CNN) have been designed, and then the most powerful and accurate model was chosen. The dataset used for the training process (for 16 screen points) consists of 2800 training images and 800 test images (with an average of 175 training images and 50 test images for each spot on the screen of the 16 spots), and it can be collected by the user of any application based on this model. The highest accuracy achieved by the best model was (91.25%) and the minimum loss was (0.23%). The best model consists of (11) layers (4 convolutions, 4 Max pooling, and 3 Dense). Python 3.7 was used to implement the algorithms, KERAS framework for the deep learning algorithms, Visual studio code as an Integrated Development Environment (IDE), and Anaconda navigator for downloading the different libraries. The model was trained with data that can be gathered using cameras of laptops or PCs and without the necessity of special and expensive equipment, also It can be trained for any single eye, depending on application requirements.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"7 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"75120193","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The field of mechanics concerned with studying the propagation of cracks in materials is Fracture Mechanics. Technology systems are meant to withstand the loads to which they are likely to be exposed when in use. Material imperfections arising at the time of production or use of the material are, however, unavoidable and must therefore be taken into account. A stress intensity factor is a fracture parameter that defines the part failure. This paper study’s the effect of cracks on the stresses of rectangular plates having a hole in the center. The plate was subjected to tensile pressure at the top side while maintaining the bottom side fixed. The plate had four cracks distributed around the centered hole at 45o at each side. The effect of the length of the cracks on the resulted stresses and strains was investigated. Also, the effect of the position of the crack on the resulted stresses and strains was studied. Finite element models for the different plate cases were built using ANSYS software. The results showed that increasing the crack length resulted to increase the stresses and strains. The dimension of the plate width, height and thickness were 150 mm, 300 mm and 1 mm respectively, and the crack position was investigated for different crack lengths (5, 10, 15, 20, 25 mm) however the results were not steady as it looks that the crack lengths have changed the stress distribution over the plate.
{"title":"Effect of Crack Length on Stresses in a Plate with a Hole","authors":"Thaker Saleh Dawood, Younis K. Khdir","doi":"10.29194/njes.25010028","DOIUrl":"https://doi.org/10.29194/njes.25010028","url":null,"abstract":"The field of mechanics concerned with studying the propagation of cracks in materials is Fracture Mechanics. Technology systems are meant to withstand the loads to which they are likely to be exposed when in use. Material imperfections arising at the time of production or use of the material are, however, unavoidable and must therefore be taken into account. A stress intensity factor is a fracture parameter that defines the part failure. This paper study’s the effect of cracks on the stresses of rectangular plates having a hole in the center. The plate was subjected to tensile pressure at the top side while maintaining the bottom side fixed. The plate had four cracks distributed around the centered hole at 45o at each side. The effect of the length of the cracks on the resulted stresses and strains was investigated. Also, the effect of the position of the crack on the resulted stresses and strains was studied. Finite element models for the different plate cases were built using ANSYS software. The results showed that increasing the crack length resulted to increase the stresses and strains. The dimension of the plate width, height and thickness were 150 mm, 300 mm and 1 mm respectively, and the crack position was investigated for different crack lengths (5, 10, 15, 20, 25 mm) however the results were not steady as it looks that the crack lengths have changed the stress distribution over the plate.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"33 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"85379520","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Many joints in the body depend on cartilage for their mechanical function. Since cartilage lacks the ability to self-heal when injured, treatments and replacements for damaged cartilage have been created in recent decades. The mechanical tests had an important role in the treatment and designing of the replaced cartilage. There are two types of cartilages in the knees: fibrocartilage (the meniscus, it is a special type of cartilage) and hyaline cartilage. Its mechanical properties are important because structural failure of cartilage is closely related with joint disorders. This study aimed to determine the stress-strain curve to give broader understanding of the material’s properties. The results of this study could help to develop computational models for evaluating mechanics of knee joint, predicting possible failure locations and disease progression in joints.The study involved two specimens taken from bovine, the first was the articular cartilage with subchondral bone and the second was the meniscus cartilage each one loaded on a compressive testing machine to compute the displacement, and the force applied, enabling the calculation of the stress-strain curve of the material.Specimen failure occurred in the articular cartilage surface at a force break of 73.8N and get force peak about 87.2 N. The meniscus cartilage failure had occurred at a force break of 29.2 N and get force peak about 34.9 N.
{"title":"Measurement of Cartilage Deformation in Intact Knee Joints under Compressive Loading","authors":"B. M. Rashid, S. Hamandi, E. Khalil","doi":"10.29194/njes.25010044","DOIUrl":"https://doi.org/10.29194/njes.25010044","url":null,"abstract":"Many joints in the body depend on cartilage for their mechanical function. Since cartilage lacks the ability to self-heal when injured, treatments and replacements for damaged cartilage have been created in recent decades. The mechanical tests had an important role in the treatment and designing of the replaced cartilage. There are two types of cartilages in the knees: fibrocartilage (the meniscus, it is a special type of cartilage) and hyaline cartilage. Its mechanical properties are important because structural failure of cartilage is closely related with joint disorders. This study aimed to determine the stress-strain curve to give broader understanding of the material’s properties. The results of this study could help to develop computational models for evaluating mechanics of knee joint, predicting possible failure locations and disease progression in joints.The study involved two specimens taken from bovine, the first was the articular cartilage with subchondral bone and the second was the meniscus cartilage each one loaded on a compressive testing machine to compute the displacement, and the force applied, enabling the calculation of the stress-strain curve of the material.Specimen failure occurred in the articular cartilage surface at a force break of 73.8N and get force peak about 87.2 N. The meniscus cartilage failure had occurred at a force break of 29.2 N and get force peak about 34.9 N.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"13 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"79017167","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
The research includes studying the mechanical properties of BNTN/PAM nanocomposites under static and dynamic conditions. The BNTN/PAM nanocomposites were prepared with different weight fractions (0, 20%, 40%, 50% and 60%) by utilizing ball milling technique. Tensile strength, Charpy impact and Shore A hardness were performed to verify any improvements in these mechanical properties of nanocomposites. The results showed significant improvements in tensile, Charpy impact, Shore A hardness properties of nanocomposites at 50% weight fraction by approximately 335%, 1422%, 63% respectively. These results started decreasing after addition of 60% of nanoclays content to PAM composites. This mechanism indicates that the percentage of weight content of BNTN could affect the mechanical properties of nanocomposites.
{"title":"The Effect of Bentonite (BNTN) Nanoclays with Multiple Weight Proportions on the Mechanical Properties of Polyacrylamide (PAM) Composites","authors":"R. Hilal","doi":"10.29194/njes.25010001","DOIUrl":"https://doi.org/10.29194/njes.25010001","url":null,"abstract":"The research includes studying the mechanical properties of BNTN/PAM nanocomposites under static and dynamic conditions. The BNTN/PAM nanocomposites were prepared with different weight fractions (0, 20%, 40%, 50% and 60%) by utilizing ball milling technique. Tensile strength, Charpy impact and Shore A hardness were performed to verify any improvements in these mechanical properties of nanocomposites. The results showed significant improvements in tensile, Charpy impact, Shore A hardness properties of nanocomposites at 50% weight fraction by approximately 335%, 1422%, 63% respectively. These results started decreasing after addition of 60% of nanoclays content to PAM composites. This mechanism indicates that the percentage of weight content of BNTN could affect the mechanical properties of nanocomposites.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"59 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"74057931","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
An experimental study on single bubble breakage in the stirred tank in oil as a continuous phase was carried out for a range of stirring speeds (220 to 430 rpm). The results are compared with bubble breakage in water that was conducted by Hasan et al. (2021) to investigate the effect of physical properties of continuous phase on the breakage rate. The breakage events in the impeller were captured and analyzed using a high speed camera. It was found that the breakage rate represented by breakage probability and a number of produced daughter bubbles (fragments) are directly proportional with the stirring speed. The breakage probability and number of produced daughter bubbles in oil was noticeably lower than that in water indicating the role the continuous phase viscosity plays in reducing the breakage rate.
在220 ~ 430转/分的搅拌速度范围内，对油作为连续相的搅拌槽内的单泡破碎进行了实验研究。将实验结果与Hasan et al.(2021)在水中进行的气泡破裂实验进行对比，研究连续相的物理性质对破裂率的影响。利用高速摄像机对叶轮破碎过程进行了捕捉和分析。研究发现，以破碎概率为代表的破碎率和产生的子泡(破片)数与搅拌速度成正比。油中的破碎概率和产生的子气泡数量明显低于水，说明连续相粘度对降低破碎率的作用。
{"title":"Single Bubble Breakage in Oil Under Stirring Conditions","authors":"Basim O. Hasan","doi":"10.29194/njes.25010006","DOIUrl":"https://doi.org/10.29194/njes.25010006","url":null,"abstract":"An experimental study on single bubble breakage in the stirred tank in oil as a continuous phase was carried out for a range of stirring speeds (220 to 430 rpm). The results are compared with bubble breakage in water that was conducted by Hasan et al. (2021) to investigate the effect of physical properties of continuous phase on the breakage rate. The breakage events in the impeller were captured and analyzed using a high speed camera. It was found that the breakage rate represented by breakage probability and a number of produced daughter bubbles (fragments) are directly proportional with the stirring speed. The breakage probability and number of produced daughter bubbles in oil was noticeably lower than that in water indicating the role the continuous phase viscosity plays in reducing the breakage rate.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"355 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"81680813","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Hala Mahmood Abdulwaahb, B. G. Rasheed, Hanadi H. Altawil
Magnesium oxide nanoparticles were deposited by laser pyrolysis process. Three types of lasers were employed CW CO2, Q-switched Nd-YAG (short pulses) and long pulses Nd-YAG lasers. The size and density of nanoparticles vary with laser energy, power, pulse duration and the scanning speed of the laser. In this method, MgO nanoparticles were deposited by a laser beam on a quartz substrate from aqueous solution of magnesium nitrate. AFM images reveal formation of small nanoparticle size of 24.5 nm with surface roughness 6.97nm by Q-switched Nd-YAG laser (10 ns) when the energy was 1J. While for CO2 laser, the smallest size was 18.8 nm at 0.4mm/s scanning speed with surface roughness 5.21nm at the same scanning speed. Moreover, long Nd-YAG pulses laser produces relatively larger average size of 37.5nm at 0.8ms pulse duration. The absorption spectra from UV-Visible spectroscopy were also conducted. The best absorption intensity was obtained at a wavelength ranging between 420-430 nm for both lasers. Finally, Thermal analysis using COMSOL Multiphysics software for the deposition process reveals that maximum temperature about 440Kfor Q-Switched Nd-YAG laser at 1J laser energy. While for RF CO2 laser, the maximum temperature obtained at 0.4mm/s scanning speed is 850K.This work provides a good knowledge for the deposition of nanoparticles using laser beams.
{"title":"Deposition of MgO Nanoparticles by Laser Pyrolysis","authors":"Hala Mahmood Abdulwaahb, B. G. Rasheed, Hanadi H. Altawil","doi":"10.29194/njes.25010020","DOIUrl":"https://doi.org/10.29194/njes.25010020","url":null,"abstract":"Magnesium oxide nanoparticles were deposited by laser pyrolysis process. Three types of lasers were employed CW CO2, Q-switched Nd-YAG (short pulses) and long pulses Nd-YAG lasers. The size and density of nanoparticles vary with laser energy, power, pulse duration and the scanning speed of the laser. In this method, MgO nanoparticles were deposited by a laser beam on a quartz substrate from aqueous solution of magnesium nitrate. AFM images reveal formation of small nanoparticle size of 24.5 nm with surface roughness 6.97nm by Q-switched Nd-YAG laser (10 ns) when the energy was 1J. While for CO2 laser, the smallest size was 18.8 nm at 0.4mm/s scanning speed with surface roughness 5.21nm at the same scanning speed. Moreover, long Nd-YAG pulses laser produces relatively larger average size of 37.5nm at 0.8ms pulse duration. The absorption spectra from UV-Visible spectroscopy were also conducted. The best absorption intensity was obtained at a wavelength ranging between 420-430 nm for both lasers. Finally, Thermal analysis using COMSOL Multiphysics software for the deposition process reveals that maximum temperature about 440Kfor Q-Switched Nd-YAG laser at 1J laser energy. While for RF CO2 laser, the maximum temperature obtained at 0.4mm/s scanning speed is 850K.This work provides a good knowledge for the deposition of nanoparticles using laser beams.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"139 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2022-04-03","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"85325445","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Soil’s characteristics are essential for the successful design of projects such as airports runway and flexible pavement. CBR (California Bering Ratio) is one of the significant soil characteristics for highways and airports projects. Thus, the CBR property can be used to determine the subgrade reaction of soil through correlations. Many of the soil geotechnical parameters such as compaction characteristics (Maximum Dry Density, MDD; Optimum Moisture Content, OMC), and consistency parameters (Liquid Limit, LL; Plastic Limit, PL; Plasticity Index, PI) can be in charge of changes that happen in soil CBR value. Soaked and/or non-soaked conditions of soils also affect CBR value. Hence, testing soils in a laboratory for CBR calculation is time-consuming that needs notable effort. Therefore, this study aims to generate some useful correlations for soil’s CBR with compaction and consistency parameters for 85 samples of fine-grained soils. The study trials were applied on natural soil samples of various places in Sulaimani Governorate, Northern Iraq. Statistical analysis has been carried out by using SPSS software (Version 28). Soaked CBR is counted, which is important for conditions such as rural roads that remain prone to water for few days. Based on the statistical analysis, there is a significant correlation between LL, PL, PI, MDD, and OMC with CBR as the dependent variable as a single variable equation with R2 of 0.7673, 0.5423, 0.5192, 0.6489, and 0.51, respectively. In addition, the highest value of R2 correlation was obtained between CBR value with consistency and compaction properties as a multiple regression equation with R2 of 0.82. The obtained equations for correlation purposes are successfully achieved and can be used, notably, to estimate CBR value.
{"title":"Prediction of California Bearing Ratio from Consistency and Compaction Characteristics of Fine-grained Soils","authors":"K. A. Rashed, N. Salih, T. Abdalla","doi":"10.29194/njes.24020123","DOIUrl":"https://doi.org/10.29194/njes.24020123","url":null,"abstract":"Soil’s characteristics are essential for the successful design of projects such as airports runway and flexible pavement. CBR (California Bering Ratio) is one of the significant soil characteristics for highways and airports projects. Thus, the CBR property can be used to determine the subgrade reaction of soil through correlations. Many of the soil geotechnical parameters such as compaction characteristics (Maximum Dry Density, MDD; Optimum Moisture Content, OMC), and consistency parameters (Liquid Limit, LL; Plastic Limit, PL; Plasticity Index, PI) can be in charge of changes that happen in soil CBR value. Soaked and/or non-soaked conditions of soils also affect CBR value. Hence, testing soils in a laboratory for CBR calculation is time-consuming that needs notable effort. Therefore, this study aims to generate some useful correlations for soil’s CBR with compaction and consistency parameters for 85 samples of fine-grained soils. The study trials were applied on natural soil samples of various places in Sulaimani Governorate, Northern Iraq. Statistical analysis has been carried out by using SPSS software (Version 28). Soaked CBR is counted, which is important for conditions such as rural roads that remain prone to water for few days. Based on the statistical analysis, there is a significant correlation between LL, PL, PI, MDD, and OMC with CBR as the dependent variable as a single variable equation with R2 of 0.7673, 0.5423, 0.5192, 0.6489, and 0.51, respectively. In addition, the highest value of R2 correlation was obtained between CBR value with consistency and compaction properties as a multiple regression equation with R2 of 0.82. The obtained equations for correlation purposes are successfully achieved and can be used, notably, to estimate CBR value.","PeriodicalId":7470,"journal":{"name":"Al-Nahrain Journal for Engineering Sciences","volume":"54 1","pages":""},"PeriodicalIF":0.0,"publicationDate":"2021-12-31","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"82650506","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：