Pub Date : 2022-10-25DOI: 10.14710/ijred.2023.47905
Undarmaa Tumenbayar, K. Ko
An investigation was performed to identify the wind veer impact on wind turbine power performance at a wind farm located on Jeju Island, South Korea. A 2 MW wind turbine was used as a test turbine. An 80 m-tall met mast was located 220 m away from the test wind turbine and a ground lidar was installed close to the met mast. The wind veer conditions were divided into four types: veering in upper and lower rotor (VV), veering in upper and backing in lower rotor (VB), backing in upper and lower rotor (BB) and backing in upper and veering in lower rotor (BV). The frequency of the four types was identified at the wind farm. The characteristics of wind veer was analysed in terms of diurnal variation and wind speed. In addition, the power curves of the four types were compared with that under no veer condition. Also, the power deviation coefficient (PDC) derived from the power outputs was calculated to identify the effect of the four types on the turbine power performance. As a result, the frequencies of the types, VV, VB, BB and BV were 62.7 %, 4.9 %, 9.2 % and 23.1 %, respectively. The PDCs for the types VV and BV were 3.0 % and 4.2 %, respectively, meaning a power gain while those for the types VB and BB were -2.9 % and -3.9 %, respectively, meaning a power loss.
{"title":"An Effect of Wind Veer on Wind Turbine Performance","authors":"Undarmaa Tumenbayar, K. Ko","doi":"10.14710/ijred.2023.47905","DOIUrl":"https://doi.org/10.14710/ijred.2023.47905","url":null,"abstract":"An investigation was performed to identify the wind veer impact on wind turbine power performance at a wind farm located on Jeju Island, South Korea. A 2 MW wind turbine was used as a test turbine. An 80 m-tall met mast was located 220 m away from the test wind turbine and a ground lidar was installed close to the met mast. The wind veer conditions were divided into four types: veering in upper and lower rotor (VV), veering in upper and backing in lower rotor (VB), backing in upper and lower rotor (BB) and backing in upper and veering in lower rotor (BV). The frequency of the four types was identified at the wind farm. The characteristics of wind veer was analysed in terms of diurnal variation and wind speed. In addition, the power curves of the four types were compared with that under no veer condition. Also, the power deviation coefficient (PDC) derived from the power outputs was calculated to identify the effect of the four types on the turbine power performance. As a result, the frequencies of the types, VV, VB, BB and BV were 62.7 %, 4.9 %, 9.2 % and 23.1 %, respectively. The PDCs for the types VV and BV were 3.0 % and 4.2 %, respectively, meaning a power gain while those for the types VB and BB were -2.9 % and -3.9 %, respectively, meaning a power loss.","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-10-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44246889","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-10-25DOI: 10.14710/ijred.2023.49368
T. Nguyen-Thi, Thi Minh Tu Bui
The paper presents the effects of blend injection and dual injection strategies on mixture formation and combustion of syngas-biogas-hydrogen fueling engine working in the solar-biomass hybrid renewable energy system. The research was performed by simulation method on a retrofitted Honda GX200 spark-ignition engine. The results show that at the end of the compression process, in the case of blend injection of 50% syngas-50% biogas, the fuel-rich zone was positioned on the top of the combustion chamber, whereas in the case of dual injection, this zone was found on the top of the piston. In the case of 50% syngas-50% hydrogen supplied, at the end of the compression process, the fuel-rich area observed on the top of the piston with slightly deflected towards the inlet port in both cases of blend and dual injection. When shifting from blend injection mode to dual injection mode, in the case of 50% syngas-50% biogas fueling engine, the mean temperature of the exhaust gas decreased from 1208 K to 1161 K and the NOx concentration decreased from 1919 ppm to 1288 ppm. In the case of a 50% syngas-50% hydrogen fueling engine, the mean exhaust gas temperature decreases from 1283 K to 1187 K leading to a decrease in NOx concentration from 3268 ppm to 2231 ppm. The dual injection has the advantage of lower NOx emission, whereas the blend injection has the advantage of higher efficiency
{"title":"Effects of Injection Strategies on Mixture Formation and Combustion in a Spark-Ignition Engine Fueled with Syngas-Biogas-Hydrogen","authors":"T. Nguyen-Thi, Thi Minh Tu Bui","doi":"10.14710/ijred.2023.49368","DOIUrl":"https://doi.org/10.14710/ijred.2023.49368","url":null,"abstract":"The paper presents the effects of blend injection and dual injection strategies on mixture formation and combustion of syngas-biogas-hydrogen fueling engine working in the solar-biomass hybrid renewable energy system. The research was performed by simulation method on a retrofitted Honda GX200 spark-ignition engine. The results show that at the end of the compression process, in the case of blend injection of 50% syngas-50% biogas, the fuel-rich zone was positioned on the top of the combustion chamber, whereas in the case of dual injection, this zone was found on the top of the piston. In the case of 50% syngas-50% hydrogen supplied, at the end of the compression process, the fuel-rich area observed on the top of the piston with slightly deflected towards the inlet port in both cases of blend and dual injection. When shifting from blend injection mode to dual injection mode, in the case of 50% syngas-50% biogas fueling engine, the mean temperature of the exhaust gas decreased from 1208 K to 1161 K and the NOx concentration decreased from 1919 ppm to 1288 ppm. In the case of a 50% syngas-50% hydrogen fueling engine, the mean exhaust gas temperature decreases from 1283 K to 1187 K leading to a decrease in NOx concentration from 3268 ppm to 2231 ppm. The dual injection has the advantage of lower NOx emission, whereas the blend injection has the advantage of higher efficiency","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-10-25","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"48617086","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-10-12DOI: 10.14710/ijred.2023.48269
Gad Reuben Mugagga, I. Omosa, T. Thoruwa
Biogas upgrading is essential in order to increase the calorific value and improve the quality of raw biogas. This present study aims at investigating the optimum performance of a near atmospheric pressure water scrubbing (NAPWS) system for biogas upgrading while using both the adsorption and absorption techniques. This was achieved through a two-stage process: namely, the Taguchi approach followed by the response surface methodology (RSM). The Taguchi orthogonal array design consisted of 27 runs where the raw biogas pressure (10 - 30 kPa), liquid flow rates (2.6 - 4.2 l/ min.) and variations of the steel wool height (0 - 45.72 cm) in the adsorption column were experimentally studied with respect to the methane (CH4) yield and removal efficiency of hydrogen sulfide (H2S) and carbon dioxide (CO2). From the experiments, the removal efficiency of hydrogen sulfide was greater than 87% with the average bio-methane content of 77.67%. During the second-stage, the analysis of variance (ANOVA) and the RSM were undertaken for optimization of the process parameters. The optimum bio-methane concentration of 84.71 (%v/v) CH4 and 13.31 (%v/v) CO2 was attained at gas pressure of 14kPa, liquid flow rate of 4.2 l/min., and steel wool height at 22.86cm obtained through numerical optimization. These results revealed that the utilization of the Taguchi and the RSM yielded to the best optimal system performance with the liquid flow rate as the most significant factor
{"title":"Optimization and Analysis of a Low-Pressure Water Scrubbing Biogas Upgrading System via the Taguchi and Response Surface Methodology Approaches","authors":"Gad Reuben Mugagga, I. Omosa, T. Thoruwa","doi":"10.14710/ijred.2023.48269","DOIUrl":"https://doi.org/10.14710/ijred.2023.48269","url":null,"abstract":"Biogas upgrading is essential in order to increase the calorific value and improve the quality of raw biogas. This present study aims at investigating the optimum performance of a near atmospheric pressure water scrubbing (NAPWS) system for biogas upgrading while using both the adsorption and absorption techniques. This was achieved through a two-stage process: namely, the Taguchi approach followed by the response surface methodology (RSM). The Taguchi orthogonal array design consisted of 27 runs where the raw biogas pressure (10 - 30 kPa), liquid flow rates (2.6 - 4.2 l/ min.) and variations of the steel wool height (0 - 45.72 cm) in the adsorption column were experimentally studied with respect to the methane (CH4) yield and removal efficiency of hydrogen sulfide (H2S) and carbon dioxide (CO2). From the experiments, the removal efficiency of hydrogen sulfide was greater than 87% with the average bio-methane content of 77.67%. During the second-stage, the analysis of variance (ANOVA) and the RSM were undertaken for optimization of the process parameters. The optimum bio-methane concentration of 84.71 (%v/v) CH4 and 13.31 (%v/v) CO2 was attained at gas pressure of 14kPa, liquid flow rate of 4.2 l/min., and steel wool height at 22.86cm obtained through numerical optimization. These results revealed that the utilization of the Taguchi and the RSM yielded to the best optimal system performance with the liquid flow rate as the most significant factor","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-10-12","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47840808","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-27DOI: 10.14710/ijred.2023.47831
Akara Kijkarncharoensin, S. Innet
Prediction accuracy is crucial for higher heating value (HHV) models to promote renewable biomass energy, especially its consistency is crucial when retraining data and knowledge of the range are unavailable. Current HHV models lack consistency in accuracy and interpretability due to various reasons. Thus, this study aimed to construct an interpretable and consistent proximate-based biomass HHV model on a wide-range dataset. The model, regime-lasso, integrated the concepts of regime-switching, lasso regression, and federated averaging to construct a consistent HHV model. The regime-switching partitioned the dataset into optimal regimes, and the lasso trained the regime models. The regime-lasso model is a collection of these models. It provided root mean square error of 0.4430– 0.9050, mean absolute error of 0.2743–0.6867, and average absolute error of 1.512–4.5894% in the literature’s wide-range datasets. The Kruskal–Wallis test confirmed the in-sample performance consistency at α=0.05, regardless of the training sets. In the out-of-sample situations without retraining, the model preserved its accuracy in six out of 11 datasets at α = 0.01. The interpretability of regime-lasso indicated the regime characteristic to be a factor of inconsistent prediction. The increase in FC had the maximum positive impact on HHV in the 2nd and 3rd regimes, while the increase in ASH negatively impacted the 1st and 2nd regimes. VM variation had neutral effects in all regimes. The regime-lasso solves the issues of accuracy declination and addresses the challenges in sensitivity analysis of the HHV model. The prediction accuracy issues of the model’s direct implementation were fixed.
{"title":"Consistent Regime-Switching Lasso Model of the Biomass Proximate Analysis Higher Heating Value","authors":"Akara Kijkarncharoensin, S. Innet","doi":"10.14710/ijred.2023.47831","DOIUrl":"https://doi.org/10.14710/ijred.2023.47831","url":null,"abstract":"Prediction accuracy is crucial for higher heating value (HHV) models to promote renewable biomass energy, especially its consistency is crucial when retraining data and knowledge of the range are unavailable. Current HHV models lack consistency in accuracy and interpretability due to various reasons. Thus, this study aimed to construct an interpretable and consistent proximate-based biomass HHV model on a wide-range dataset. The model, regime-lasso, integrated the concepts of regime-switching, lasso regression, and federated averaging to construct a consistent HHV model. The regime-switching partitioned the dataset into optimal regimes, and the lasso trained the regime models. The regime-lasso model is a collection of these models. It provided root mean square error of 0.4430– 0.9050, mean absolute error of 0.2743–0.6867, and average absolute error of 1.512–4.5894% in the literature’s wide-range datasets. The Kruskal–Wallis test confirmed the in-sample performance consistency at α=0.05, regardless of the training sets. In the out-of-sample situations without retraining, the model preserved its accuracy in six out of 11 datasets at α = 0.01. The interpretability of regime-lasso indicated the regime characteristic to be a factor of inconsistent prediction. The increase in FC had the maximum positive impact on HHV in the 2nd and 3rd regimes, while the increase in ASH negatively impacted the 1st and 2nd regimes. VM variation had neutral effects in all regimes. The regime-lasso solves the issues of accuracy declination and addresses the challenges in sensitivity analysis of the HHV model. The prediction accuracy issues of the model’s direct implementation were fixed.","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-27","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"44074234","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-26DOI: 10.14710/ijred.2023.45312
J. Benhamou, El Bachir Lahmer, M. Jami, M. Moussaoui, A. Mezrhab
The thermohydraulic performance of a new design solar air heater (SAH) design was examined experimentally in this paper as a trial to improve the flat-plate SAH’s efficiency. A flat-plate solar air heater (FPSAH) and a jacketed tubular solar air heater (JTSAH) having similar dimensions were constructed to compare their thermal performance efficiencies. A band of Aluminum jacketed tubes were arranged side by side in parallel to the airflow direction to form the absorber of a jacketed tubular solar air heater (JTSAH). The experiments were accomplished at three mass flow rates (MFR)s: 0.011 kg/s. 0.033 kg/s, and 0.055 kg/s. Results revealed that the maximum temperature difference was obtained from JTSAH at 38°C in comparison to 32°C from the FPSAH at MFR of 0.011 kg/s. The thermal losses from the upper glass cover of the JTSAH were less than the same losses at the FPSAH due to the reduced absorber and glass temperatures of the JTSAH. The gained power was higher at the JTSAH than the FPSAH. At the JTSAH, at 0.055 kg/s MFR, the maximum average thermal efficiency obtained was 81%, and the maximum average thermos-hydraulic efficiency obtained was 75.61 %. It is noted that increasing the MFR increases the thermal efficiency, also, its optimum value rises the thermos-hydraulic efficiency to a specific optimum point. The pressure drop increases with the MFR and JTSAH compared to the FPSAH
{"title":"Experimental Evaluation of Thermohydraulic Performance of Tubular Solar Air Heater","authors":"J. Benhamou, El Bachir Lahmer, M. Jami, M. Moussaoui, A. Mezrhab","doi":"10.14710/ijred.2023.45312","DOIUrl":"https://doi.org/10.14710/ijred.2023.45312","url":null,"abstract":"The thermohydraulic performance of a new design solar air heater (SAH) design was examined experimentally in this paper as a trial to improve the flat-plate SAH’s efficiency. A flat-plate solar air heater (FPSAH) and a jacketed tubular solar air heater (JTSAH) having similar dimensions were constructed to compare their thermal performance efficiencies. A band of Aluminum jacketed tubes were arranged side by side in parallel to the airflow direction to form the absorber of a jacketed tubular solar air heater (JTSAH). The experiments were accomplished at three mass flow rates (MFR)s: 0.011 kg/s. 0.033 kg/s, and 0.055 kg/s. Results revealed that the maximum temperature difference was obtained from JTSAH at 38°C in comparison to 32°C from the FPSAH at MFR of 0.011 kg/s. The thermal losses from the upper glass cover of the JTSAH were less than the same losses at the FPSAH due to the reduced absorber and glass temperatures of the JTSAH. The gained power was higher at the JTSAH than the FPSAH. At the JTSAH, at 0.055 kg/s MFR, the maximum average thermal efficiency obtained was 81%, and the maximum average thermos-hydraulic efficiency obtained was 75.61 %. It is noted that increasing the MFR increases the thermal efficiency, also, its optimum value rises the thermos-hydraulic efficiency to a specific optimum point. The pressure drop increases with the MFR and JTSAH compared to the FPSAH","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-26","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"47415980","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-15DOI: 10.14710/ijred.2023.46864
Rawit Khamharnphol, I. Kamdar, J. Waewsak, Somphol Chiwamongkhonkarn, Sakrapee Khunpetcha, C. Kongruang, Y. Gagnon
This paper presents a techno-economic assessment of a 100 kWp solar rooftop photovoltaic (PV) system at five hospitals in central southern Thailand. The system encompasses 100 kWp PV panels, 100 kW grid-tied inverters and balance of system (BOS) under the grid code of the Provincial Electricity Authority (PEA). The latest PV technology of bifacial mono-crystalline solar panels, inverters and BOS were simulated along with the Meteonorm 7.3 database using the PVsyst simulation toolkit with different tilt angles, orientations, solar radiations and ambient temperature. The technical aspects of solar rooftop PV power generation systems include the annual energy output and the performance ratio (PR) under IEC standard. Further, an economic analysis of the model was examined using a cost benefit analysis (CBA) and various assumptions. Four main financial criteria, i.e., benefit cost ratio (BCR), net present value (NPV), internal rate of return (IRR), and payback period (PBP) were evaluated under three different scenarios: (1) self-consumption scheme, (2) feed-in tariff (FiT) scheme, and (3) private power purchase agreement (PPA) scheme. Finally, the levelized cost of energy (LCOE) was also calculated. The results reveal that the Takua Thung hospital is characterized by the maximum average global horizontal irradiation (GHI) and the maximum annual produced energy of 199 kWh/m2 and 164.8 MWh/year, respectively. The PR calculated for all hospital sites is above 85%. The outcomes of the financial analysis show that the optimum scenarios are PPA and FiT schemes. The LCOE analysed in this study indicates that the Takua Thung hospital site has the lowest LCOE at 2.47 THB/kWh (0.07 USD/kWh). This research confirms the potential for hospitals and stakeholders in central southern Thailand for investments in solar rooftop PV systems
{"title":"Techno-Economic Assessment of a 100 kWp Solar Rooftop PV System for Five Hospitals in Central Southern Thailand","authors":"Rawit Khamharnphol, I. Kamdar, J. Waewsak, Somphol Chiwamongkhonkarn, Sakrapee Khunpetcha, C. Kongruang, Y. Gagnon","doi":"10.14710/ijred.2023.46864","DOIUrl":"https://doi.org/10.14710/ijred.2023.46864","url":null,"abstract":"This paper presents a techno-economic assessment of a 100 kWp solar rooftop photovoltaic (PV) system at five hospitals in central southern Thailand. The system encompasses 100 kWp PV panels, 100 kW grid-tied inverters and balance of system (BOS) under the grid code of the Provincial Electricity Authority (PEA). The latest PV technology of bifacial mono-crystalline solar panels, inverters and BOS were simulated along with the Meteonorm 7.3 database using the PVsyst simulation toolkit with different tilt angles, orientations, solar radiations and ambient temperature. The technical aspects of solar rooftop PV power generation systems include the annual energy output and the performance ratio (PR) under IEC standard. Further, an economic analysis of the model was examined using a cost benefit analysis (CBA) and various assumptions. Four main financial criteria, i.e., benefit cost ratio (BCR), net present value (NPV), internal rate of return (IRR), and payback period (PBP) were evaluated under three different scenarios: (1) self-consumption scheme, (2) feed-in tariff (FiT) scheme, and (3) private power purchase agreement (PPA) scheme. Finally, the levelized cost of energy (LCOE) was also calculated. The results reveal that the Takua Thung hospital is characterized by the maximum average global horizontal irradiation (GHI) and the maximum annual produced energy of 199 kWh/m2 and 164.8 MWh/year, respectively. The PR calculated for all hospital sites is above 85%. The outcomes of the financial analysis show that the optimum scenarios are PPA and FiT schemes. The LCOE analysed in this study indicates that the Takua Thung hospital site has the lowest LCOE at 2.47 THB/kWh (0.07 USD/kWh). This research confirms the potential for hospitals and stakeholders in central southern Thailand for investments in solar rooftop PV systems","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-15","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"42727326","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-10DOI: 10.14710/ijred.2023.43246
Marymagdaline Enowmbi Tarkang, Fetus Fatai Adedoyin, F. Bekun
Previously documented studies in the literature on how tourism leads to economic growth in the form of tourism-led growth hypotheses (TLGH) has been investigated. This study presents a new perspective on the growth of tourism by considering its impact on conventional energy consumption, real income level, and emission via the channel of globalization. Sequences of econometric tests were conducted to validate the hypothesized claims between tourism development and growth impact on conventional energy consumption and pollution proxy by ecological footprints, globalization GDP per capita, biocapacity, and tourists for the case of France. Empirical evidence from the Granger causality test presents a uni-directional causality from ecological footprints to GDP per capita and from biocapacity to ecological footprints. The correlation matrix shows interrelation amongst series with biocapacity significantly correlating with ecological footprints with tourist’s arrival having a positive correlation with ecological footprints and a negative one with biocapacity. GPD per capita was found to positively affect the ecological footprints and have a negative correlation with biocapacity and a significant relationship with tourists' arrivals. Additionally, globalization exerts a positive impact on ecological footprints, and its effect on biocapacity was found to be negative although globalization's effect on tourists’ arrivals and per capita GDP is significant. The ARDL estimation indicated biocapacity as a neutral agent for ecological footprints, tourist arrivals having a negative impact on ecological footprints, and globalization significantly affecting ecological footprints. From these findings, it is evident that tourism growth has a significant impact on energy consumption and pollution. Policy recommendations were also provided in this study accordingly.
{"title":"An Investigation into the Role of Tourism Growth, Conventional Energy Consumption and Real Income on Ecological Footprint Nexus in France","authors":"Marymagdaline Enowmbi Tarkang, Fetus Fatai Adedoyin, F. Bekun","doi":"10.14710/ijred.2023.43246","DOIUrl":"https://doi.org/10.14710/ijred.2023.43246","url":null,"abstract":"Previously documented studies in the literature on how tourism leads to economic growth in the form of tourism-led growth hypotheses (TLGH) has been investigated. This study presents a new perspective on the growth of tourism by considering its impact on conventional energy consumption, real income level, and emission via the channel of globalization. Sequences of econometric tests were conducted to validate the hypothesized claims between tourism development and growth impact on conventional energy consumption and pollution proxy by ecological footprints, globalization GDP per capita, biocapacity, and tourists for the case of France. Empirical evidence from the Granger causality test presents a uni-directional causality from ecological footprints to GDP per capita and from biocapacity to ecological footprints. The correlation matrix shows interrelation amongst series with biocapacity significantly correlating with ecological footprints with tourist’s arrival having a positive correlation with ecological footprints and a negative one with biocapacity. GPD per capita was found to positively affect the ecological footprints and have a negative correlation with biocapacity and a significant relationship with tourists' arrivals. Additionally, globalization exerts a positive impact on ecological footprints, and its effect on biocapacity was found to be negative although globalization's effect on tourists’ arrivals and per capita GDP is significant. The ARDL estimation indicated biocapacity as a neutral agent for ecological footprints, tourist arrivals having a negative impact on ecological footprints, and globalization significantly affecting ecological footprints. From these findings, it is evident that tourism growth has a significant impact on energy consumption and pollution. Policy recommendations were also provided in this study accordingly. ","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"49123654","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-10DOI: 10.14710/ijred.2023.47137
Y. Lahlou, Abdelghani Hajji, M. Aggour
Today, renewable energy and energy efficiency are key to limiting global warming and preventing the dangerous effects of climate change. The biggest problem with conventional solar and wind turbine systems is the intermittency of electrical power generation. Even if these two energy sources can be complementary, the space occupied by these hybrid systems remains very important. This work proposes an improved management algorithm for a patented transformable photovoltaic-wind system, which mainly uses two flexible photovoltaic panels which are automatically deformed by an electromechanical system from the planar shape to the semi-cylindrical shape of the Savonius wind turbine blades. When weather conditions change, this system switches to eco-friendly photovoltaic (PV) or wind turbine (WT) mode, allowing a good total power generation from two solar power sources or wind turbine power. The contribution brought for this work relates to the realization and the improvement of the management algorithm to determine a better change to the mode PV or the mode WT. The operation test was simulated in 8760 hours for the year 2021. This developed algorithm allows several theoretical calculations of the power produced from solar radiation and wind speed data, thereafter the algorithm compare and determines the overall power and selects the optimal PV or WT mode. In this study, the overall power generated by the invented system produces more electricity per hour, the power Pt increases by 75.55% compared to the power Pwt, and also the power Pt increases by 68.15% compared to Pvp power.
{"title":"Optimization of a Management Algorithm for an Innovative System of Automatic Switching between Two Photovoltaic and Wind Turbine Modes for an Ecological Production of Green Energy","authors":"Y. Lahlou, Abdelghani Hajji, M. Aggour","doi":"10.14710/ijred.2023.47137","DOIUrl":"https://doi.org/10.14710/ijred.2023.47137","url":null,"abstract":"Today, renewable energy and energy efficiency are key to limiting global warming and preventing the dangerous effects of climate change. The biggest problem with conventional solar and wind turbine systems is the intermittency of electrical power generation. Even if these two energy sources can be complementary, the space occupied by these hybrid systems remains very important. This work proposes an improved management algorithm for a patented transformable photovoltaic-wind system, which mainly uses two flexible photovoltaic panels which are automatically deformed by an electromechanical system from the planar shape to the semi-cylindrical shape of the Savonius wind turbine blades. When weather conditions change, this system switches to eco-friendly photovoltaic (PV) or wind turbine (WT) mode, allowing a good total power generation from two solar power sources or wind turbine power. The contribution brought for this work relates to the realization and the improvement of the management algorithm to determine a better change to the mode PV or the mode WT. The operation test was simulated in 8760 hours for the year 2021. This developed algorithm allows several theoretical calculations of the power produced from solar radiation and wind speed data, thereafter the algorithm compare and determines the overall power and selects the optimal PV or WT mode. In this study, the overall power generated by the invented system produces more electricity per hour, the power Pt increases by 75.55% compared to the power Pwt, and also the power Pt increases by 68.15% compared to Pvp power.","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-10","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"43612195","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-08DOI: 10.14710/ijred.2023.47048
M. Yanis, N. Zaini, Isra Novari, Faisal Abdullah, B. G. Dewanto, M. Isa, Marwan Marwan, M. Zainal, Abdurrahman Abdurrahman
Geothermal energy, as a part of green and renewable energy, has been widely developed in the world to replace the current conventional fossil energy. Peut Sagoe is an active volcano in the northern part of Sumatra. The volcanic mountain has not been completely explored for geothermal and energy reserves study. This is due to the volcano locates in a high topography and surrounded by dense tropical forest, which makes it challenging to deploy geophysical instruments in the area. The Landsat 8 thermal infrared and meteorological data from 2013 – 2020 were used to estimate the energy resources by calculating the radiative heat flux (RHF) and measuring the energy lost annually through the heat discharge rate (HDR). We also used the normalized differential vegetation index (NDVI) for vegetation analysis, and estimation of its emissivity data. The mono-window algorithm was used to calculate the land surface temperature (LST). The Stefan–Boltzmann equation was utilized to analyze thermal infrared data for RHF, and ambient temperature and relative humidity data were acquired from the Indonesian Meteorological Agency (BMKG) database. The results showed that low vegetation values and high LST of 25°C–35°C were found in crater areas, which indicate the underground thermal activities of the mountain. It demonstrates that the maximum RHF values were 55 W/m2 in 2013 and 37 W/m2 in 2020. The HDR data were calculated by applying 15% of the RHF data, and the amounts of energy lost were 132.5 MWe and 64.5 MWe in 2013 and 2015 respectively. It increased to 186.4 MWe in 2017 and 89 MWe in 2020. Based on these predicted results, we conclude that the combination of thermal infrared imagery of Landsat 8 and meteorological data is an effective approach in estimating geothermal energy potential and energy loss of volcanoes situated in remote areas
{"title":"Monitoring of Heat Flux Energy in the Northernmost Part of Sumatra Volcano Using Landsat 8 and Meteorological Data","authors":"M. Yanis, N. Zaini, Isra Novari, Faisal Abdullah, B. G. Dewanto, M. Isa, Marwan Marwan, M. Zainal, Abdurrahman Abdurrahman","doi":"10.14710/ijred.2023.47048","DOIUrl":"https://doi.org/10.14710/ijred.2023.47048","url":null,"abstract":"Geothermal energy, as a part of green and renewable energy, has been widely developed in the world to replace the current conventional fossil energy. Peut Sagoe is an active volcano in the northern part of Sumatra. The volcanic mountain has not been completely explored for geothermal and energy reserves study. This is due to the volcano locates in a high topography and surrounded by dense tropical forest, which makes it challenging to deploy geophysical instruments in the area. The Landsat 8 thermal infrared and meteorological data from 2013 – 2020 were used to estimate the energy resources by calculating the radiative heat flux (RHF) and measuring the energy lost annually through the heat discharge rate (HDR). We also used the normalized differential vegetation index (NDVI) for vegetation analysis, and estimation of its emissivity data. The mono-window algorithm was used to calculate the land surface temperature (LST). The Stefan–Boltzmann equation was utilized to analyze thermal infrared data for RHF, and ambient temperature and relative humidity data were acquired from the Indonesian Meteorological Agency (BMKG) database. The results showed that low vegetation values and high LST of 25°C–35°C were found in crater areas, which indicate the underground thermal activities of the mountain. It demonstrates that the maximum RHF values were 55 W/m2 in 2013 and 37 W/m2 in 2020. The HDR data were calculated by applying 15% of the RHF data, and the amounts of energy lost were 132.5 MWe and 64.5 MWe in 2013 and 2015 respectively. It increased to 186.4 MWe in 2017 and 89 MWe in 2020. Based on these predicted results, we conclude that the combination of thermal infrared imagery of Landsat 8 and meteorological data is an effective approach in estimating geothermal energy potential and energy loss of volcanoes situated in remote areas","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":"1 1","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-08","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"66964062","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
Pub Date : 2022-09-05DOI: 10.14710/ijred.2023.46696
S. Channouf, Y. Admi, M. Jami, M. Moussaoui
Lattice Boltzmann method (LBM) is employed in the current work to simulate two-phase flows of immiscible fluids over a square obstacle in a 2D computational domain using the Rothman-Keller color gradient model. This model is based on the multiphase Rothman-Keller description, it is used to separate two fluids in flow and to assess its efficacy when treating two fluids in flow over a square obstacle with the objective of reducing turbulence by adjusting the viscosities of the two fluids. This turbulence can cause major problems such as interface tracking techniques in gas-liquid flow and upward or downward co-current flows in pipes. So, the purpose of the study is to replace a single fluid with two fluids of different viscosities by varying these viscosities in order to reduce or completely eliminate the turbulence. The results show that to have stable, parallel and non-overlapping flows behind the obstacle, it is necessary that the difference between the viscosities of the fluids be significant. Also, showing that the increase in the viscosity ratio decreases the time corresponding to the disappearance of the vortices behind the obstacle. The results presented in this work have some general conclusions: For M≥2, the increase in the viscosity difference leads to an increasing of friction between fluids, reducing of average velocity of flow and decreasing the time corresponding to the disappearance of the vortices behind the obstacle. However, for M≤1/2, the opposite occurs.
{"title":"Study of Two Layered Immiscible Fluids Flow in a Channel with Obstacle by Using Lattice Boltzmann RK Color Gradient Model","authors":"S. Channouf, Y. Admi, M. Jami, M. Moussaoui","doi":"10.14710/ijred.2023.46696","DOIUrl":"https://doi.org/10.14710/ijred.2023.46696","url":null,"abstract":"Lattice Boltzmann method (LBM) is employed in the current work to simulate two-phase flows of immiscible fluids over a square obstacle in a 2D computational domain using the Rothman-Keller color gradient model. This model is based on the multiphase Rothman-Keller description, it is used to separate two fluids in flow and to assess its efficacy when treating two fluids in flow over a square obstacle with the objective of reducing turbulence by adjusting the viscosities of the two fluids. This turbulence can cause major problems such as interface tracking techniques in gas-liquid flow and upward or downward co-current flows in pipes. So, the purpose of the study is to replace a single fluid with two fluids of different viscosities by varying these viscosities in order to reduce or completely eliminate the turbulence. The results show that to have stable, parallel and non-overlapping flows behind the obstacle, it is necessary that the difference between the viscosities of the fluids be significant. Also, showing that the increase in the viscosity ratio decreases the time corresponding to the disappearance of the vortices behind the obstacle. The results presented in this work have some general conclusions: For M≥2, the increase in the viscosity difference leads to an increasing of friction between fluids, reducing of average velocity of flow and decreasing the time corresponding to the disappearance of the vortices behind the obstacle. However, for M≤1/2, the opposite occurs.","PeriodicalId":44938,"journal":{"name":"International Journal of Renewable Energy Development-IJRED","volume":" ","pages":""},"PeriodicalIF":2.5,"publicationDate":"2022-09-05","publicationTypes":"Journal Article","fieldsOfStudy":null,"isOpenAccess":false,"openAccessPdf":"","citationCount":null,"resultStr":null,"platform":"Semanticscholar","paperid":"45073095","PeriodicalName":null,"FirstCategoryId":null,"ListUrlMain":null,"RegionNum":0,"RegionCategory":"","ArticlePicture":[],"TitleCN":null,"AbstractTextCN":null,"PMCID":"","EPubDate":null,"PubModel":null,"JCR":null,"JCRName":null,"Score":null,"Total":0}
京公网安备 11010802042870号
京ICP备2023020795号-1
扫码关注我们
求助内容：
应助结果提醒方式：